Commit graph

3766 commits

Author SHA1 Message Date
Jouni Malinen
c3dc68e844 Do not invalidate EAP session cache on all network block parameter changes
The bssid and priority parameters in a network block do not have any
effect on the validity of an EAP session entry, so avoid flushing the
cached session when only these parameters are changed. This is mainly to
allow forced roaming or network selection changes without causing fast
reauthentication to be disabled if the changes are done during RSN
association that used EAP.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-03-16 19:44:32 +02:00
Jouni Malinen
c6c29be1bd Interworking: Add credential realm to EAP-TLS identity
If the configured credential includes a username without '@' (i.e., no
realm) in it and a realm, combine these to form the EAP-Request/Identity
value as "<username>@<realm>" for EAP-TLS. This was already done for
EAP-TTLS as part of the anonymous NAI conversion, but EAP-TLS could have
ended up using a username without any realm information which would be
unlikely to work properly with roaming cases.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-03-11 21:06:15 +02:00
Lior David
dfe0745c9a P2P: Add optional op_class argument to P2P_SET listen_channel
The existing implementation in p2p_ctrl_set used a hard-coded operating
class 81 which is only suitable for the social channels in the 2.4 GHz
band, and will not work for the social channel in the 60 GHz band.
Extend this by adding an optional op_class argument to P2P_SET
listen_channel. If not specified, use the default value of 81 to match
existing behavior.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-03-07 13:51:01 +02:00
Naveen Singh
c7fb678f31 D-Bus: Add association response status code property for failure cases
(Re)Association Response frame with status code other than 0 is now
notified over DBUS as a part of PropertiesChanged signal. This can be
used by application in case AP is denying association with status code
17 (band steering) so that it does not interfere in the BSSID selection
logic of wpa_supplicant.

Signed-off-by: Naveen Singh <nasingh@google.com>
2016-03-06 20:44:51 +02:00
Janusz Dziedzic
56e2fc2c31 wpa_supplicant: Add ctrl parameter to INTERFACES command
"INTERFACES ctrl" can now be used to fetch a list of network interfaces
and their control interfaces, e.g., to fetch the UDP port information
for the control interface.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2016-03-05 17:44:49 +02:00
Janusz Dziedzic
acf57fae76 ctrl_iface_common: Use sockaddr_storage instead of sockaddr_un
This is a step towards allowing UDP sockets to be used with the common
implementation.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2016-03-05 17:15:05 +02:00
Janusz Dziedzic
1a2124c650 wpa_supplicant: Use common functions for ctrl_iface
Use the common functions, structures when UNIX socket ctrl_iface used.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2016-03-05 17:15:05 +02:00
Janusz Dziedzic
d60886cdaf wpa_supplicant: Add monitor support for global UDP ctrl_iface
Add monitor support (ATTACH/DETACH) for the global ctrl_iface when using
the UDP backend.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2016-03-05 10:46:13 +02:00
Janusz Dziedzic
f0e5d3b5c6 wpa_supplicant: Share attach/detach/send UDP ctrl_iface functions
Extend the previously per-interface UDP ctrl_iface functions
(attach/detach/send) to support operations on the global interface as
well.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2016-03-05 10:21:18 +02:00
Janusz Dziedzic
db7fb435f3 wpa_supplicant: Allow UDP ctrl_iface configuration to set the UDP port
This allows the UDP port to be set for the per-interface and global
control interfaces. The format is: udp:<port_no>

For example:
wpa_supplicant -Dnl80211 -ddt -g udp:9888

And in the configuration file:
ctrl_interface=udp:9877

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2016-03-05 10:15:57 +02:00
Eliad Peller
c69ef1d2da P2P: Respect p2p_ignore_shared_freq on p2p_group_add
Make sure wpas_p2p_init_go_params() respects the p2p_ignore_shared_freq
configuration option. Choose currently used frequencies only if this
option is not set, or if there are no unused channels left.

Signed-off-by: Eliad Peller <eliad@wizery.com>
2016-03-04 21:17:32 +02:00
Eliad Peller
4115b0524b P2P: Fix shared freq print in wpas_p2p_init_go_params()
"freq" contains the forced frequency, not the selected one. Print the
correct freq instead.

Signed-off-by: Eliad Peller <eliad@wizery.com>
2016-03-04 21:16:00 +02:00
Ben Rosenfeld
a805731086 P2P: Abort ongoing scan when p2p_find is stopped
When p2p_find is stopped, send request to the driver
in order to cancel an ongoing scan if there is one.

Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
2016-03-03 17:10:26 +02:00
Ilan Peer
1446afc865 wpa_supplicant: Handle EVENT_SCAN_RESULTS when an interface is disabled
An interface can be disabled while it has an ongoing scan request.
In such a case, when the scan results notification is received,
it was being ignored (as the interface is already disabled) so the
scan state was not cleared. This can cause undetermined behavior
for the next scan request.

To handle this, clear the scan state when EVENT_SCAN_RESULTS is
received and the interface is disabled.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2016-03-03 17:10:26 +02:00
Avraham Stern
d14e63a2aa WNM: Do not scan based on malformed BSS Transition Management Request
Verify that when the Candidate List Included bit is set in a BSS
Transition Management Request frame, the candidate list actually
includes at least one candidate. If no candidates are included, reject
the request without scanning.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-03-03 17:10:25 +02:00
Avraham Stern
f420577f3c WNM: Fix candidates count in BSS Transition Management Request
In BSS Transition Management Request frame, it is possible that vendor
specific IEs are included after the candidate list. In this case the
candidates count was incremented for each IE although the candidate list
is already over which could result in adding all zeros candidates into
the neighbor list.

Fix that by incrementing the candidates count only for neighbor report
elements.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-03-03 17:09:26 +02:00
Ilan Peer
3c58df7ae7 wpa_cli: Support running action script on global control interface
In case wpa_cli is started with an option to execute an action script,
but no interface is specified, wpa_cli might crash in wpa_cli_exec() if
arg1 == NULL. Fix this be setting arg1 = "global".

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2016-03-03 16:30:28 +02:00
Adam Langley
8f38eed628 Android: Remove superfluous OpenSSL include paths
The libcrypto and libssl modules (and their respective static and host
versions) use LOCAL_EXPORT_C_INCLUDE_DIRS thus just including the module
is sufficient.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2016-03-03 16:27:10 +02:00
Daichi Ueura
cbf8d181c3 HS 2.0R2: Clear fetch_anqp_in_progress if fopen fails
Clear wpa_s->fetch_anqp_in_progress when osu-providers.txt can't be
opened. An issue happens, for instance, when wpa_supplicant doesn't
have correct access permission to the directory specified by osu_dir.
If hs20_osu_fetch_done method returns without clearing the flag,
'FETCH_OSU' command will never work correctly.

Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
2016-03-03 16:25:49 +02:00
Jouni Malinen
2bf9a53a8b Add EAP-AKA' and EAP-pwd to wpa_supplicant README
The EAP methods were missing from the lists.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-03-03 16:19:55 +02:00
Jouni Malinen
4196c08e8b Update notes about OpenSSL versions
Obsolete OpenSSL versions 0.9.* are not supported anymore.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-03-03 16:17:34 +02:00
Jouni Malinen
5d7b1a3c82 Fix some typos in wpa_supplicant README files
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-03-03 16:15:46 +02:00
Nishant Chaprana
4194fee565 README-P2P: Fix a typo
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
2016-03-03 16:00:34 +02:00
Lior David
c58eed6dc7 P2P: Add Dev Info attribute to Probe Request frames in 60 GHz
When building P2P IE for Probe Request frames in P2P scan, add the
device information attribute if the 60 GHz band is included in the scan,
since this is required by the P2P specification.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-03-03 15:13:56 +02:00
Lior David
2b6e9f91df wpa_supplicant: Expose wpas_get_bands() and related API
Expose the functions wpas_get_bands() and wpas_freq_to_band() and the
enum wpa_radio_work_band, since they will be needed outside
wpa_supplicant.c.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-03-03 15:10:50 +02:00
Lior David
94ad3c3389 P2P: Change order of P2P IE and frequencies set up
When setting up parameters for P2P scan, calculate the frequencies
for the scan before calculating the scan IE. This is because
the scan IE calculation may need information about the scan
frequencies in use.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-03-03 15:03:46 +02:00
Jouni Malinen
bef5e9a862 Fix scan rescheduling from wpas_stop_pno to check postponed case
Commit 02e122a995 ('Reschedule scan from
wpas_stop_pno if it was postponed') uses wpa_s->scanning as the only
condition for automatically starting a postponed scan request from
EVENT_SCHED_SCAN_STOPPED event handler. However, wpa_s->scanning may be
set for sched_scan and as such, this can result in unexpected extra
scans without there having been any real postponed request.

Make this more accurate by verifying that there really is a pending
request for a scan before speeding up its start.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-03-03 11:04:38 +02:00
Lior David
96a26ab744 P2P: Support dedicated P2P_DEVICE without separate group interface
Add support for drivers with dedicated P2P_DEVICE interface, but without
group interface concurrency (only a single netdev is used). With such
devices, wpa_supplicant tried to use the p2p_dev interface instead of
the group interface and most P2P operations failed. Extend
wpa_supplicant to use the primary interface instead of a separate group
interface in such cases.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-02-27 19:37:19 +02:00
Lior David
ba307f8528 P2P: Add a separate pointer to the P2P Device instance
In many places in the code there was a reference to wpa_s->parent to get
from group interface to p2p_dev interface. These places can break if
P2P_DEVICE interface would need to be used with the primary interface as
the group interface, since the parent of the primary interface points to
itself and not the p2p_dev interface.

Fix this by adding a separate "p2pdev" pointer to wpa_supplicant,
it will be the same as parent pointer in most cases but whenever
the primary interface is used as a group interface, change it to
point to the correct p2p_dev interface.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-02-27 19:37:19 +02:00
Jouni Malinen
e04019737e GAS client: Make PMF check on RX more consistent
Use the SA field instead of BSSID in the received Action frame to
determine whether PMF has been negotiated with the transmitter. While
these fields are supposed to be same for Public Action frames from an
AP, it would be possible that a frame is received with different values.
The following operations in gas_query_rx() use SA, so do the same for
the PMF check.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-02-27 19:37:19 +02:00
Jouni Malinen
0645492e7c WNM: Optimize a single BSS transition management candidate scan
If the BSS Transition Management Request frame includes only a single
candidate and we need to scan for the BSS to get up-to-date information,
use a scan for the known BSSID instead of wildcard BSSID. In addition,
set the SSID in the scan if it is known based on old scan results in the
BSS table. This removes unnecessary Probe Response frames when we are
interested in results from only a single BSS.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-02-26 17:19:20 +02:00
Jouni Malinen
eb20cea590 nl80211: Add an option to specify the BSSID to scan for
This allows scans to be optimized when a response is needed only from a
single, known BSS.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-02-26 17:19:20 +02:00
Jouni Malinen
940491ce08 MBO: Mandate use of PMF for WPA2+MBO association (STA)
If WPA2 is used, MBO AP must enable PMF. Refuse to select a BSS that has
MBO and WPA2 enabled without PMF.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-02-22 19:53:05 +02:00
Jouni Malinen
6332aaf3b2 MBO: Track STA cellular data capability from association request
This makes hostapd parse the MBO attribute in (Re)Association Request
frame and track the cellular data capability (mbo_cell_capa=<val> in STA
control interface command).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-02-22 19:53:05 +02:00
Jouni Malinen
d010048cf7 MBO: Expire non-matching bss_tmp_disallowed entries as part of check
This makes wpa_is_bss_tmp_disallowed() expire old entries from the
bss_tmp_disallowed list even if they do not match the BSSID that is
being searched for. This allows the list to be kept at shorter length to
speed up operations and minimize memory use in cases where the
previously disabled BSS is not in radio range anymore.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-02-22 19:53:04 +02:00
Avraham Stern
016082e9e6 MBO: Send WNM-Notification when cellular capabilities change
Send a WNM-Notification to the associated AP to indicate changes in
cellular data capabilities.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
Avraham Stern
c484b19882 Move Hotspot 2.0 element in (Re)Association Request frames
According to IEEE Std 802.11-2012, Table 8-22, vendor specific elements
must follow all other elements, so Hotspot 2.0 element which is actually
a vendor specific element must come after all other elements.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
Avraham Stern
a0c38e5dd7 Re-order elements in (Re)Association Request frames
According to IEEE Std 802.11-2012, Table 8-22, RM Enabled Capabilities
element must come before the Extended Capabilities element.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
Avraham Stern
9a493fab73 WNM: Add candidate list to BSS transition query
Add an option to configure a candidate list to BSS transition query
("list" as the second argument to WNM_BSS_QUERY). The candidate list is
built from the available scan results. If no updated scan results (< 10
sec) are available, the command fails.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
Avraham Stern
84d1c0fd5a WNM: Add candidate list to BSS transition response
Add the transition candidate list to BSS Transition Management Response
frame. The candidates preference is set using the regular wpa_supplicant
BSS selection logic. If the BSS transition request is rejected and
updated scan results are not available, the list is not added.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
Avraham Stern
c8082d2b6a MBO: Add MBO IE to BSS Transition Management Response frame
When rejecting a BSS Transition Management Request frame, add MBO IE to
the BSS Transition Management Response frame to specify the transition
rejection reason.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
Avraham Stern
dd5999084e MBO: Parse MBO IE in BSS Transition Management Request frames
Add parsing of MBO IE in BSS Transition Management Request frames. If
the MBO IE includes the association retry delay attribute, do not try to
reconnect to the current BSS until the delay time is over.

If the MBO IE includes the cellular data connection preference attribute
or the transition rejection reason attribute, send a message to upper
layers with the data.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
Avraham Stern
5e57ba2505 MBO: Add Supported Operating Classes element to Association Request
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
Avraham Stern
7d46f586de MBO: Add global operating class definitions
Add definitions for global operating classes. These definitions will be
used to construct supported operating classes information element.

The operating classes definitions used locally for P2P module will be
removed and included in the general operating classes definitions.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
David Spinadel
cb06cf3456 MBO: Prevent association to APs that explicitly disallow this
Prevent association to MBO APs that have association disallowed
attribute in MBO IE in Beacon or Probe Response frames.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-02-22 19:53:04 +02:00
David Spinadel
c5d193d7b3 MBO: Add cellular capability to MBO IE
Add cellular capability attribute to MBO IE and add MBO IE with cellular
capabilities to Probe Request frames. By default, cellular capability
value is set to Not Cellular capable (3).

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-02-22 19:53:04 +02:00
David Spinadel
2d5b8614b7 MBO: Send MBO WNM-Notification Request frames to notify changes
Send a WNM-Notification Request frame with Non-preferred Channel Report
subelement if the non-preferred channels list changes during an
association.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-02-22 19:53:04 +02:00
David Spinadel
92c6e2e3a9 MBO: Implement MBO non-preferred channel report in Association Request
Add MBO IE with non-preferred channels to (Re)Association Request
frames.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-02-22 19:53:04 +02:00
David Spinadel
facf2c728a MBO: Add non-preferred channel configuration in wpa_supplicant
Add non-preferred channel configuration to wpa_config for MBO.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-02-21 17:55:16 +02:00
Avraham Stern
231b04b6cb utils: Share a single helper function to get IE by ID
Add a helper function to find a certain IE inside IEs buffer by ID and
use this function in several places that implemented similar
functionality locally.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-21 17:14:56 +02:00