This implements processing of FILS Authentication frame for FILS shared
key authentication with ERP and PMKSA caching.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Station should be able to connect initially without ft_pmk_cache filled,
so the target AP has the PSK available and thus the same information as
the origin AP. Therefore neither caching nor communication between the
APs with respect to PMK-R0 or PMK-R1 or VLANs is required if the target
AP derives the required PMKs locally.
This patch introduces the generation of the required PMKs locally for
FT-PSK. Additionally, PMK-R0 is not stored (and thus pushed) for FT-PSK.
So for FT-PSK networks, no configuration of inter-AP communication is
needed anymore when using ft_psk_generate_local=1 configuration. The
default behavior (ft_psk_generate_local=0) remains to use the pull/push
protocol.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This patch add functionality of mesh SAE PMKSA caching. If the local STA
already has peer's PMKSA entry in the cache, skip SAE authentication and
start AMPE with the cached value.
If the peer does not support PMKSA caching or does not have the local
STA's PMKSA entry in the cache, AMPE will fail and the PMKSA cache entry
of the peer will be removed. Then STA retries with ordinary SAE
authentication.
If the peer does not support PMKSA caching and the local STA uses
no_auto_peer=1, the local STA can not retry SAE authentication because
NEW_PEER_CANDIDATE event cannot start SAE authentication when
no_auto_peer=1. So this patch extends MESH_PEER_ADD command to use
duration(sec). Throughout the duration, the local STA can start SAE
authentication triggered by NEW_PEER_CANDIDATE even though
no_auto_peer=1.
This commit requires commit 70c93963ed
('SAE: Fix PMKID calculation for PMKSA cache'). Without that commit,
chosen PMK comparison will fail.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends the wpa_supplicant PMKSA_FLUSH control interface command to
allow the PMKSA list from the authenticator side to be flushed for AP
and mesh mode. In addition, this adds a hostapd PMKSA_FLUSH control
interface command to flush the PMKSA entries.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends the wpa_supplicant PMKSA control interface command to allow
the PMKSA list from the authenticator side to be listed for AP and mesh
mode. In addition, this adds a hostapd PMKSA control interface command
to show the same list for the AP case.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The FT RRB hostapd packets have a length field. For PULL frames, it
counted the bytes starting with nonce and up to the last before pad. For
RESP frames, it counted the bytes starting with nonce and up to the last
before pad except for 2 bytes. For PUSH frames, it counted the bytes
starting with nonce and up to including pad.
As rounding is done with AES encryption, including pad does not make
sense. Not including the last field before pad does not make sense
either. These were broken in the earlier addition of the 2 octet
pairwise field in commit 1b484d60e5 ('FT:
Include pairwise cipher suite in PMK-R0 SA and PMK-R1 SA').
AES encryption is not affected, as rounding hides the differences. The
packets data_length field is not used, so the differences have no effect
there.
This patch changes the constants to match the bytes used, thus excluding
the pad. To validate the changes, look at remainder modulo 8 of the sum
of the size constants and the padding sizes.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
The SAE PMKID is calculated with IEEE Std 802.11-2012 11.3.5.4, but the
PMKID was re-calculated with 11.6.1.3 and saved into PMKSA cache. Fix
this to save the PMKID calculated with 11.3.5.4 into the PMKSA cache.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
In addition to the PTK length increasing, the length of the PMK was
increased (from 256 to 384 bits) for the 00-0f-ac:12 AKM. This part was
missing from the initial implementation and a fixed length (256-bit) PMK
was used for all AKMs.
Fix this by adding more complete support for variable length PMK and use
384 bits from MSK instead of 256 bits when using this AKM. This is not
backwards compatible with the earlier implementations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This ensures that group key is set as long as the interface exists.
Additionally, ifconfig_up is needed as wpa_group will enter
FATAL_FAILURE if the interface is still down. Also vlan_remove_dynamic()
is moved after wpa_auth_sta_deinit() so vlan_remove_dynamic() can check
it was the last user of the wpa_group.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This allows the new own_ie_override=<hexdump> configuration parameter to
be used to replace the normally generated WPA/RSN IE(s) for testing
purposes in CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the AP/Authenticator receives an EAPOL-Key msg 2/4 for an association
that negotiated use of PSK and the EAPOL-Key MIC does not match, it is
likely that the station is trying to use incorrect PSK/passphrase.
Report this with "AP-STA-POSSIBLE-PSK-MISMATCH <STA addr>" control
interface event.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows WPA2 mode AP to be re-enabled automatically after external
ifconfig down + up on a netdev used by hostapd.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends Disconnect-Request processing to check against PMKSA cache
entries if no active session (STA association) match the request.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes hostapd create PMKSA cache entries from SAE authentication
and allow PMKSA caching to be used with the SAE AKM.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the PMK-R1 needs to be pulled for the R0KH, the previous
implementation ended up rejecting the over-the-air authentication and
over-the-DS action frame unnecessarily while waiting for the RRB
response. Improve this by postponing the Authentication/Action frame
response until the pull response is received.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows hostapd to set a different management group cipher than the
previously hardcoded default BIP (AES-128-CMAC). The new configuration
file parameter group_mgmt_cipher can be set to BIP-GMAC-128,
BIP-GMAC-256, or BIP-CMAC-256 to select one of the ciphers defined in
IEEE Std 802.11ac-2013.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new mechanism allows P2P Client to request an IPv4 address from the
GO as part of the 4-way handshake to avoid use of DHCP exchange after
4-way handshake. If the new mechanism is used, the assigned IP address
is shown in the P2P-GROUP-STARTED event on the client side with
following new parameters: ip_addr, ip_mask, go_ip_addr. The assigned IP
address is included in the AP-STA-CONNECTED event on the GO side as a
new ip_addr parameter. The IP address is valid for the duration of the
association.
The IP address pool for this new mechanism is configured as global
wpa_supplicant configuration file parameters ip_addr_go, ip_addr_mask,
ip_addr_star, ip_addr_end. For example:
ip_addr_go=192.168.42.1
ip_addr_mask=255.255.255.0
ip_addr_start=192.168.42.2
ip_addr_end=192.168.42.100
DHCP mechanism is expected to be enabled at the same time to support P2P
Devices that do not use the new mechanism. The easiest way of managing
the IP addresses is by splitting the IP address range into two parts and
assign a separate range for wpa_supplicant and DHCP server.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It was already possible to configure hostapd and wpa_supplicant to use
FT-SAE for the key management, but number of places were missing proper
AKM checks to allow FT to be used with the new AKM.
Signed-hostap: Jouni Malinen <j@w1.fi>
When using per-device PSKs, select the PSK based on the P2P Device
Address of the connecting client if that client is a P2P Device. This
allows the P2P Interface Address to be changed between P2P group
connections which may happen especially when using persistent groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to implement per-device PSK selection based on the
peer's P2P Device Address instead of P2P Interface Address.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is needed to avoid allowing the STA to reconnect using a cached
PMKSA. ESS disassoc imminent notification is normally used to indicate
that the STA session will be terminated and as such, requiring full
authentication through the authentication server after this is needed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
For some testing it can be useful to force the Key MIC in group
EAPOL-Key frames to be corrupt. Add an option to allow setting a
probability for corrupting the Key MIC and use it in the WPA code,
increasing the first byte of the MIC by one to corrupt it if desired.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Replace CONFIG_IEEE80211V with CONFIG_WNM to get more consistent build
options for WNM-Sleep Mode operations. Previously it was possible to
define CONFIG_IEEE80211V without CONFIG_WNM which would break the build.
In addition, IEEE 802.11v has been merged into IEEE Std 802.11-2012 and
WNM is a better term to use for this new functionality anyway.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 296a34f0c1 changed hostapd to
remove the internal STA entry at the beginning of TKIP countermeasures.
However, this did not take into account the case where this is triggered
by an EAPOL-Key error report from a station. In such a case, WPA
authenticator state machine may continue processing after having
processed the error report. This could result in use of freed memory.
Fix this by stopping WPA processing if the STA entry got removed.
Signed-hostap: Jouni Malinen <j@w1.fi>
This introduces new AKM for SAE and FT-SAE and adds the initial parts
for going through the SAE Authentication frame exchange. The actual SAE
algorithm and new fields in Authentication frames are not yet included
in this commit and will be added separately. This version is able to
complete a dummy authentication with the correct authentication
algorithm and transaction values to allow cfg80211/mac80211 drivers to
be tested (all the missing parts can be handled with
hostapd/wpa_supplicant changes).
Signed-hostap: Jouni Malinen <j@w1.fi>
disable_dgaf=1 in hostapd.conf can now be used to disable downstream
group-addressed forwarding (DGAF). In this configuration, a unique
GTK (and IGTK) is provided to each STA in the BSS to make sure the
keys do not match and no STA can forge group-addressed frames.
An additional mechanism in the AP needs to be provided to handle some
group-addressed frames, e.g., by converting DHCP packets to unicast
IEEE 802.11 frames regardless of their destination IP address and by
providing Proxy ARP functionality.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Split WPA initialization into two parts so that the Beacon frames can be
configured fully before the initial keys (GTK/IGTK) are configured. This
makes it easier for drivers that depend on the AP security mode being
fully set before the keys are configured.
A new hostapd configuration parameter, disable_pmksa_caching=1, can now
be used to disable PMKSA caching on the Authenticator. This forces the
stations to complete EAP authentication on every association when WPA2
is being used.
Some deployed supplicants update their SNonce for every receive
EAPOL-Key message 1/4 even when these messages happen during the
same 4-way handshake. Furthermore, some of these supplicants fail
to use the first SNonce that they sent and derive an incorrect PTK
using another SNonce that does not match with what the authenticator
is using from the first received message 2/4. This results in
failed 4-way handshake whenever the EAPOL-Key 1/4 retransmission
timeout is reached. The timeout for the first retry is fixed to
100 ms in the IEEE 802.11 standard and that seems to be short
enough to make it difficult for some stations to get the response
out before retransmission.
Work around this issue by increasing the initial EAPOL-Key 1/4
timeout by 1000 ms (i.e., total timeout of 1100 ms) if the station
acknowledges reception of the EAPOL-Key frame. If the driver does
not indicate TX status for EAPOL frames, use longer initial
timeout (1000 ms) unconditionally.
hostapd does not implement UAPSD functionality. However, if U-APSD
functionality is implemented outside hostapd, add support to advertise
the functionality in beacon.
Signed-off-by: yogeshp@marvell.com
This is needed to fix PTK derivation to use correct length. Previously,
64-octet PTK may have been derived if the authenticator did not already
have a STA entry. Now, the correct pairwise cipher suite is learned when
then PMK-R1 SA is received.
The three existing enums were already depending on using the same
values in couple of places and it is just simpler to standardize on
one of these to avoid need for mapping between different enums for
the exact same thing.
Doxygen and some build tools may get a bit confused about same file
name being used in different directories. Clean this up a bit by
renaming some of the duplicated file names in src/ap.
Jouni Malinen
Michael Braun
Masashi Honma
Jouni Malinen
Thomas Pedersen
Johannes Berg
Xi Chen
Shan Palanisamy
Jouni Malinen
Yogesh Ashok Powar