The PBC ignore-start workaround just needs to check whether
the time is within 5 seconds, so should use monotonic time.
While at it, add a few more ifdefs to clearly separate the
code and variables needed.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
PBC sessions are just time-stamped when activated, and
eventually time out, so should use monotonic time.
While at it, make the code use os_reltime_expired().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Even though the length of this buffer is based only on locally
configured information, it is cleaner to include explicit buffer room
validation steps when adding the attributes into the buffer.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes it easier to handle cases where the application is restarted
and the previously used local TCP port may not have been fully cleared
in the network stack.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Some APs may incorrectly change Device Password ID from PBC in M1 to
Default PIN in M2 even when they are ready to continue with PBC. This
behavior used to work with earlier implementation in wpa_supplicant, but
commit b4a17a6ea7 started validating this
as part of a change that is needed to support NFC configuration method.
While this kind of AP behavior is against the WSC specification and
there could be potential use cases for moving from PBC to PIN, e.g., in
case of PBC session overlap, it is justifiable to work around this issue
to avoid interoperability issues with deployed APs. There are no known
implementations of PBC-to-PIN change from M1 to M2, so this should not
reduce available functionality in practice.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes the P2P Device Address of the Enrollee available with the PSK
records to allow P2P Device Address instead of P2P Interface Address to
be used for finding the correct PSK.
Signed-hostap: Jouni Malinen <j@w1.fi>
"wpa_cli p2p_set per_sta_psk <0/1>" can now be used to disable/enable
use of per-device PSKs in P2P groups. This is disabled by default.
When enabled, a default passphrase is still generated by the GO for
legacy stations, but all P2P and non-P2P devices using WPS will get
a unique PSK.
This gives more protection for the P2P group by preventing clients from
being able to derive the unicast keys used by other clients. This is
also a step towards allowing specific clients to be removed from a group
reliably without having to tear down the full group to do so.
Signed-hostap: Jouni Malinen <j@w1.fi>
According to WSC specification (Ver 2.0.2, section 8.3), RF Bands
attribute should be set to the specific RF band used for the current
message. Add an option to set wanted band in wps_build_rf_bands() and
add a callback to get the current band from wpa_supplicant and hostapd.
Signed-hostap: David Spinadel <david.spinadel@intel.com>
Commit b4a17a6ea7 added support for the
WPS Registrar to change the Device Password based on WSC specification
design. However, this added validation for Registrar behavior which
resulted in preventing a common P2P use case from working. Relax the
validation rules for builds with P2P enabled to allow the Enrollee (P2P
client) accepting M1/M2 changes in Device Password Id between Default
and Registrar-specified PIN.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is a C compiler extension and not needed, so replace with standard
compliant way of calculating the pointer.
Signed-hostap: Jouni Malinen <j@w1.fi>
"WPS_ER_START ifname=<interace>" can now be used to force a specific
interface to be used for UPnP operations. This is especially useful for
automated test cases where the lo interface can now be used easily to
perform ER operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
There are quite a few places in the current implementation where a nul
terminated string is generated from binary data. Add a helper function
to simplify the code a bit.
Signed-hostap: Jouni Malinen <j@w1.fi>
When a specific out-of-band Device Password is enabled, it can be useful
to be able to advertise that in the selected registrar information.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"WPS_NFC_CONFIG_TOKEN <WPS/NDEF> <network id>" can now be used to build
an NFC configuration token from a locally configured network.
Signed-hostap: Jouni Malinen <j@w1.fi>
This extends the WPS ER commands that previously accepted only UUID as
an identifier for an AP to use either UUID or BSSID for this.
Signed-hostap: Jouni Malinen <j@w1.fi>
wps_build_public_key() takes the dh_ctx into use and another attempt to
use the same DH keys fails with wps->dh_ctx being set to NULL. Avoid
this by using the DH parameters only if dh_ctx is valid. This fixes
cases where a use of local pre-configured DH keys followed by an
operating using peer DH keys would faild due to unexpected attempt to
use local keys again.
Signed-hostap: Jouni Malinen <j@w1.fi>
WSC specification 2.0 section 7.4 describes OOB password to be expressed
in ASCII format (upper case hexdump) instead of raw binary.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"WPS_NFC_TOKEN <WPS/NDEF>" used to generate a new NFC password token
regardless of whether there was a pre-configured token in the
configuration. Change this to use the pre-configured value, if
available, instead. This allows the same command to be used to write the
password token to an NFC tag more conveniently.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Registrar is allowed to propose another Device Password ID in M2. Make
Enrollee validate Device Password ID in M2 to check if this happened.
This commit adds support for changing from NFC password token to default
PIN for the case where the AP is the Enrollee and has both the NFC
password token and AP PIN enabled at the same time.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since there could be multiple carrier records, it is cleaner to build
only the WPS carrier record instead of full NFC connection handover
request within wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
WSC IE in Beacon and Probe Response frames should behave consistently
as far as the RF Bands attribute is concerned. Use the same dualband
condition for adding this into Probe Response frames since the value
is not really needed if the AP is not a dualband AP.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some deployed station implementations implement WPS incorrectly and
end up causing PBC session overlap issues by indicating active PBC
mode in a scan after the WPS provisioning step. Work around this by
ignoring active PBC indication in a Probe Request from a station that
completed PBC provisioning during the last five seconds.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The UFD (USB flash drive) configuration method was deprecated in WSC
2.0. Since this is not known to be used, remove the UFD implementation
from hostapd and wpa_supplicant to allow the WPS implementation to be
cleaned up. This removes the now unused OOB operations and ctrl_iface
commands that had already been deprecated by the new NFC operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
If WPS Registrar tries to provision a WPA/WPA2-Personal network without
including a valid Network Key, the network block cannot be used to
connect to the network. Reject such credential without adding the
network block. This makes wpa_supplicant send WSC_NACK as a response to
the invalid Credential and stop the provisioning process immediately
rather than only after trying unsuccessfully to connect to the network.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The old WPS interface for using NFC has no known deployments and even
the binary libraries referenced here are not easily available anymore.
Since the new interface for using NFC with WPS covers the same
functionality, remove the old implementation to clean up WPS
implementation.
Signed-hostap: Jouni Malinen <j@w1.fi>
When WPS is used with NFC connection handover, the AP may indicate its
operating channel within the credential information. Use this
informatiom, if present, to speed up the scan process.
Signed-hostap: Jouni Malinen <j@w1.fi>
This commit adds new wpa_supplicant ctrl_iface commands to allow
external programs to go through NFC connection handover mechanism
with wpa_supplicant taking care of the WPS processing. This version
includes only the case where wpa_supplicant is operating as a
station/Enrollee.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, WPS Registrar allowed multiple wildcard PINs to be
configured. This can get confusing since these PINs get assigned to any
Enrollee that does not have a specific PIN and as such, cannot really be
used with different PIN values in reasonable ways. To avoid confusion
with multiple enabled PINs, invalidate any previously configured
wildcard PIN whenever adding a new one.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Maintain state of WPS APs during iteration to find the correct AP for
WPS PIN operation when no specific BSSID is specified. This information
can be used for optimizing the order in which the APs are tried. This
commit is only adding the collection of the information and more
detailed debug information to make debug logs more helpful in figuring
out how the AP selection order could be improved.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Multiple memcmps of nonces were actually comparing only the first byte
instead of all 16 bytes. [Bug 462]
Signed-hostap: Eyal Shapira <eyal@wizery.com>
intended-for: hostap-1
This functionality could be shared for other commands, too, so move
it to a common function. In addition, implement the validation in a
bit more strict way to avoid accepting values like '-123' as a valid
PIN.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new hostapd ctrl_iface command WPS_NFC_TOKEN can now be used to
manage AP-as-Enrollee operations with NFC password token. WPS/NDEF
parameters to this command can be used to generate a new NFC password
token. enable/disable parameters can be used to enable/disable use of
NFC password token (instead of AP PIN) for external Registrars.
A preconfigured NFS password token can be used by providing its
parameters with new hostapd.conf fields wps_nfc_dev_pw_id,
wps_nfc_dh_pubkey, wps_nfc_dh_privkey, and wps_nfc_dev_pw. This use
will also depend on WPS_NFC_TOKEN enable/disable commands, i.e., the
configured NFS password token is disabled by default.
Signed-hostap: Jouni Malinen <j@w1.fi>
