list_networks() always used the wlanX control interface to query for the
current list of networks. However, when a dedicated P2P Device is used,
the global control interface should be used when checking persistent
group network profiles.
Fix this by adding an optional parameter indicating that the P2P
networks are requested, and in such a case use the global control
interface.
In addition update test_p2p_persistent to use the argument when needed.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
This is required for cases that a dedicated P2P Device interface
is used and then the event will happen on the global interface.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Send request to set persistent_reconnect on the global control
interface so it would also work when using a dedicated P2P Device
interface.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
When testing P2P invitation flow, setting the NFC selector
should be done using the global control interface.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Some tests in test_p2ps.py test a scenario where a separate P2P
group interface is not used. However, this is not a valid case
when a dedicated P2P Device interface is used, as in such a case
a separate group interface must be used.
Handle this by skipping such tests in case a dedicated P2P Device is
used.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Call group_form_result() whenever a new group is started, so that
group_ifname gets updated and later, the group can be removed when
needed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When resetting a device, remove all the P2P networks to prevent
unexpected behavior in following tests. This is needed for the case
where P2P Device interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
This is required for cases where P2P Device is used and the event
happens on the global interface.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
This is required for cases that multiple interfaces are used and the
event can happen on any of them, for example when a dedicated P2P Device
interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
The tests used p2p_dev_addr that can be different from own_addr,
if a dedicated P2P Device interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Couple of the EAP-SIM/AKA protocol test cases were leaving out the
Reserved field. This was not intentional since these test cases were
targeting a specific Subtype processing instead of verifying truncated
header case (which is covered separately). Add the Reserved field to
allow the implementation to add an explicit, earlier check for this.
Signed-off-by: Jouni Malinen <j@w1.fi>
Number of the P2P test cases through D-Bus commands were not prepared
for there being a separate group interface when the P2P Device concept
is used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Enhance test ap_vlan_wpa2_radius_id_change to change the VLAN-ID
back as a last step. This ensures that the wpa_group for VLAN-ID 1
did not enter FATAL_FAILURE state during the test.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
In addition, this adds some delay between the authentication and data
connectivity test through the newly added VLAN and by doing so, makes
ap_vlan_wpa2_radius_id_change a bit more robust. It was possible for the
EAPOL-Key message 4/4 not having yet been processed by hostapd at the
time the data test started.
Signed-off-by: Jouni Malinen <j@w1.fi>
dynamic_vlan=required also applies to macaddr_acl=2 (RADIUS), especially
when used with WPA-PSK.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
The time before trying to associate with an AP that does not advertise
Selected Registrar TRUE is going to be incremented, so increase the
autogo_m2d timeout to avoid reporting incorrect errors due to missing
M2D events.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This change add two new tests to verify hostapd operation when used with
VLANs. Both are based on pmksa_cache_preauth and enable dynamic VLANs,
pmksa_cache_preauth_vlan_used additionally uses a station with VID 1.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
It looks like it was possible to receive an incomplete FAIL line and
break out from test execution due to a parsing error. Handle this more
robustly and log the error.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Now that there is a kernel patch for IPv6 ProxyARP that is capable of
using the non-AP STAs MAC address as the link layer source address in
NA, validate that behavior rather than the temporary check for BSSID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The 'params' argument was not used at all. Use it as an alternative
means for setting the list of test cases to execute.
Signed-off-by: Jouni Malinen <j@w1.fi>
