Add an explicit check for modes != NULL instead of depending on
num_modes > 0 implying that. This is to silence invalid static analyzer
reports.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Support adding/deleting vendor elements dynamically for AP mode while it
is started by wpa_supplicant instead of hostapd which already supported
this. This adds ap_assocresp_elements global parameter and UPDATE_BEACON
control interface command to take the changed values into effect.
Usage in wpa_cli:
Add vendor IE for (Re)Association Response frames
> set ap_assocresp_elements=xxxx
Add vendor IE for Beacon/Probe Response frames
> set ap_vendor_elements=xxxx
Delete vendor IE from (Re)Association Response frames
> set ap_assocresp_elements
Delete vendor IE from Beacon/Probe Response frames
> set ap_vendor_elements
To make vendor IE changes take effect
> update_beacon
Signed-off-by: Chaoli Zhou <zchaoli@codeaurora.org>
Add support to send DSCP Policy Query frame using a new control
interface command DSCP_QUERY. This includes support for a wildcard DSCP
query and a DSCP query with a single Domain Name attribute.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Add support to parse WFA Capabilities element from the (Re)Association
Response frame. Also register a timeout for the station to wait before
sending a new DSCP query if requested by AP.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Indicate DSCP Policy capability by including a WFA Capabilities element
containing the relevant bit set to 1 in the (Re)Association Request
frames when enabled by user.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Add support to prepare and send DSCP response action frame to the
connected AP in response to a new control interface command DSCP_RESP.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Add support to parse received DSCP Policy Request frames and send the
request details as control interface events.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
The DSCP policy capability is disabled by default. The user frameworks
which have support for handling DSCP policy request messages need to
enable this capability explicitly to allow wpa_supplicant to advertise
the capability to the AP and allow the related frames to be processed.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
This function is not specific to GAS, so make it available throughout
wpa_supplicant without requiring CONFIG_GAS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Enhance the P2P_GROUP_ADD command to support DFS channel with 80 and 160
MHz bandwidth to be used for autonomous GO when using offloaded DFS.
For example, 'P2P_GROUP_ADD freq=5500 max_oper_chwidth=80 ht40 vht'
- Previous behavior: AP fallback to channel 100 using 20 MHz with
"No VHT higher bandwidth support for the selected channel 100"
- Enhanced behavior: AP starts on channel 100 using 80 MHz with
"VHT center channel 106 for 80 or 80+80 MHz bandwidth"
This functionality is on top of the driver's capability to offload DFS,
which is advertized through WPA_DRIVER_FLAGS_DFS_OFFLOAD.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Enable support for P2P connection in 6 GHz with the channel width of 40
MHz, 80 MHz, and 160 MHz. The flag max_oper_chwidth is used to configure
the maximum channel width for P2P connection in 6 GHz with the commands
P2P_CONNECT, P2P_INVITE, and P2P_GROUP_ADD.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Current definition of wpas_p2p_get_ht40_mode() determines secondary
offset in the 5 GHz band. Enhance the functionality of this function to
determine offset to support 6 GHz channels also.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Clone pmf and p2p_6ghz_disable configuration values when creating a new
P2P group interface. PMF is required in 6 GHz band operation.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Currently while selecting a preferred frequency when no preference is
known, p2p_no_go_freq is not considered for 5 GHz and 60 GHz channels.
This results in starting GO on the channels that are configured not to
allow the local device as GO.
Use wpas_p2p_supported_freq_go api to check if the p2p_no_go_freq
configuration before selecting the preferred frequency for GO.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
For some 6 GHz operating class like 134, there is a possibility where
the ch variable used for channel iterator overflows when it is
incremented. Fix this by updating the datatype of ch variable to
avoid integer overflow while incrementing.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Generate an event on the control socket interface when a network is
added or removed. The event name CTRL-EVENT-NETWORK-<ADDED|REMOVED>
is followed by the network entry identifier. The event matches the
corresponding Network<Added|Removed> signal on the d-bus interface.
Signed-off-by: Andrew Beltrano <anbeltra@microsoft.com>
The --conf option specifies a file containing a list of options
to configure the network used for running the test which will be
used in place of the defaults built into the script.
Signed-off-by: Nick Porter <nick@portercomputing.co.uk>
"SET disable_mscs_support 1" can be used to disable indication of MSCS
support in the Extended Capabilities element for testing purposes. This
is also disabling addition of the MSCS element even if valid
configuration parameters had been configured.
Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
Add support to receive and process SCS Response frames from the AP and
indicate the status to upper layers.
Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
"SET disable_scs_support 1" can be used to disable indication of SCS
support in the Extended Capabilities element for testing purposes.
Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
Add support to parse SCS control interface command and form the SCS
Request frame to be sent to SCS enabled AP.
Signed-off-by: Vinita S. Maloo <vmaloo@codeaurora.org>
Enable (and require) the management frame protection for the P2P GO if
it is started on a 6 GHz channel.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
P2P connections in the 6 GHz band use SAE authentication algorithm after
getting credentials with WPS connection. During WPS connection as it
doesn't use SAE, SAE PT is not derived. After getting SAE credentials,
the STA connects to the same SSID using SAE auth algorithm. Earlier, SAE
H2E PT was not derived while connecting to the same SSID to which the
STA is connected last time. Due to this, the P2P group formation fails
for 6 GHz channels when H2E is enabled as the PT will not be setup by
the P2P client before proceeding to the SAE authentication. Same could
happen with infrastructure WPS when wps_cred_add_sae=1 is used.
Set up the SAE H2E PT while connecting to the same SSID again also to
make sure that the H2E PT is set up in the STA to derive the PWE for
successful SAE authentication. The PT derivation will be skipped in
wpa_s_setup_sae_pt() if PT is already available for that SSID.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Though both 5 GHz channels and 6 GHz channels report the mode as
HOSTAPD_MODE_IEEE80211A, there is a possibility of different HT/VHT/HE
capabilities being available between these bands. Use get_mode() to
obtain correct capabilities to cover cases where the driver reports
different capability values for the 5 GHz and 6 GHz channels.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Determine if the TDLS peer supports TDLS in 6 GHz band based on the HE 6
GHz Band Capabilities element received in the TDLS Setup Response frame.
Indicate the peer's HE 6 GHz capabilities to the driver through
sta_add().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
External applications can store PMKSA entries persistently and
reconfigure them to wpa_supplicant after restart. This can result in
wpa_supplicant having a PMKSA for FILS authentication without having
matching ERP keys for it which would prevent the previously added
mechanism for dropping FILS PMKSA entries to recover from rejected
association attempts.
Fix this by clearing PMKSA entries configured by external applications
upon FILS connection failure even when ERP keys are not available.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
wpa_supplicant generates both a PMKSA cache entry and ERP keys upon
successful FILS connection and uses FILS authentication algorithm for
subsequent connections when either ERP keys or a PMKSA cache entry is
available.
In some cases, like AP/RADIUS server restart, both ERP keys and PMKSA
becomes invalid. But currently when an AP rejects an association,
wpa_supplicant marks only ERP keys as failed but not clearing PMKSA.
Since PMKSA is not cleared, consecutive connection attempts are still
happening with FILS authentication algorithm and connection attempts are
failing with the same association rejection again instead of trying to
recover from the state mismatch by deriving a new ERP key hierarchy.
Clear PMKSA entries as well on association rejection from an AP to allow
the following connection attempt to go with open authentication to
re-establish a valid ERP key hierarchy. Also, since clearing PMKSA
entries on unprotected (Re)Association Response frames could allow DoS
attack (reduce usability of PMKSA caching), clear PMKSA entries only
when ERP keys exists.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
CTRL-EVENT-AUTH-REJECT reporting was previously skipped when going
through SAE-specific Authentication frame handling. Add this event here
as well to be more consistent with control interface events.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use WPA3-Personal (SAE+PMF) for P2P connections in the 6 GHz band to
enable the Wi-Fi Display use case on the 6 GHz band without having to
use WPA2-Personal (PSK) on that new band.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Previously, 6 GHz channels were disabled for P2P operations. Use the new
allow_6ghz parameter with P2P_CONNECT, P2P_GROUP_ADD, and P2P_INVITE
commands for P2P connection on the 6 GHz channels when Wi-Fi Display is
enabled on both the devices.
However, the p2p_6ghz_disable parameter in the configuration takes a
higher precedence.
Indicate P2P 6 GHz band capable information in Device Capability Bitmap
of P2P Capability attribute to indicate the P2P Device is capable of P2P
operation in the 6 GHz band.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Introduce a new allow_6ghz parameter with P2P_CONNECT, P2P_GROUP_ADD,
and P2P_INVITE commands for P2P connection on the 6 GHz channels when
Wi-Fi Display is enabled on both the devices. This commit is only adding
the interface change without changing any actual P2P functionality.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Previously, the 6 GHz channels were disabled for P2P operations.
Introduce a new include_6ghz parameter for the P2P_FIND command to
configure P2P discovery on the 6 GHz channels.
However, the p2p_6ghz_disable parameter in the configuration takes a
higher priority. If the p2p_6ghz_disable parameter is not set in the
configuration, include_6ghz parameter can be used to enable or disable
the discovery operation in the 6 GHz channels for the P2P_FIND command.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Extend the previously 5 GHz specific 80 and 160 MHz channels helper
functions to support 6 GHz channels.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Do not skip scan results with zero length SSID (i.e., a hidden SSID)
when searching for potential BSS transition candidates since such
entries might be for the same ESS (i.e., for the current SSID). Use only
the BSSID check for such cases.
Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
This helper function returns enum chan_allowed values, so use it as the
return type instead of unnecessarily generic int.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It is safer to remove and free these entries with a shared helper
function to avoid issues with potentially forgetting to unregister or
free something if this structure is extended in the future.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When a STA makes an association request that is rejected by an OCE AP
due to the RSSI being insufficient, the AP is added to the driver
disallow list by wpa_set_driver_tmp_disallow_list().
Once the AP increases TX power which makes the AP RSSI higher than
Association Rejection RSSI threshold, the AP is supposed to be removed
from the driver disallow list but that was not the case.
wpa_is_bss_tmp_disallowed() is called in the scan result handler, so it
is the best place to put the logic of removing the AP from the driver
disallow list with sufficient AP RSSI.
This is needed with drivers that use the temporarily disallowed BSS list
(which is currently supported only with a QCA vendor command). The
wpa_supplicant internal functionality was already taking care of this
with the wpa_is_bss_tmp_disallowed() return value even for cases where
the entry remaining in the list.
Signed-off-by: Hu Wang <huw@codeaurora.org>
APs in 6 GHz operating with LPI/VLP rules will have significantly lower
SNR values compared to 2.4/5 GHz band APs. Earlier, the estimated
throughputs were used for comparison only when the delta of SNRs between
both the APs was not greater than 7 and as a result for comparing 6 GHz
APs with 2.4/5 GHz APs, estimated throughputs were not getting used.
The estimated throughput calculations takes SNR value also into
consideration, hence remove RSSI delta check if any of the APs are from
the 6 GHz band. This change is limited to the 6 GHz band only in order
to avoid possible regressions with 2.4/5 GHz APs.
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
This makes it convenient for an external test script to use
ext_eapol_frame_io=1 to delay and/or modify transmission of EAPOL-Key
msg 1/4 without having to use separate frame injection mechanisms.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Prefer 6 GHz APs when estimated throughputs are equal with APs from the
2.4/5 GHz bands while selecting APs for connection. Also add a 6 GHz
specific noise floor default value for the 6 GHz band (with the same
value as was used for 5 GHz previously) to make this step clearer.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support to consider HE rates while estimating throughputs for the
scan results from HE enabled APs. HE 0.8 usec GI rates are used in all
tables. The minimum SNR values for HE rates (1024-QAM) are derived by
adding the existing minimum SNR values of 256-QAM rates from VHT tables
and the difference between the values of minimum sensitivity levels of
256-QAM rates and 1024-QAM rates defined in Table 27-51 (Receiver
minimum input level sensitivity) in IEEE P802.11ax/D8.0.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support to calculate estimated throughputs for APs which support the
160 MHz (including 80+80 MHz) mode in VHT. The minimum SNR values for
VHT 160 MHz mode are derived from minimum SNR values used for VHT 80 MHz
mode + 3 dBm. The min-SNR values are derived relatively based on the
information that the minimum sensitivity levels defined in Table 21-25
(Receiver minimum input level sensitivity) in IEEE Std 802.11-2020 for
the 160 MHz mode are higher by 3 dBm compared to the values of the 80
MHz mode for each rate.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add checks for features supported by the specific hardware mode of the
local device that has the channel for which the throughput is being
estimated instead of assuming the local device supports all optional
features. This is more accurate for cases where the local capabilities
might differ based on the band. In addition, this is in preparation for
extending rate estimates to cover optional VHT and HE features.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When the driver provides a list of supported modes, chan6 ended getting
added even if the 2.4 GHz mode was not included. This resulted in
incorrect behavior of trying to transmit on a not supported channel in
case of 5 GHz only radios.
Fix this by adding the channel 6 by default only if the driver does not
provide a list of supported modes. Whenever the supported modes are
available, only add this channel if it is explicitly listed as an
enabled channel.
Fixes: 8e5739c3ac ("DPP2: Check channel 6 validity before adding it to chirp channel list")
Signed-off-by: Kani M <kanisumi@codeaurora.org>
Simplify the implementation by using shared functions for parsing the
capabilities instead of using various similar but not exactly identical
checks throughout the implementation.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE Std 802.11-2020 mandates H2E to be used whenever an SAE password
identifier is used. While this was already covered in the
implementation, the sae_prepare_commit() function still included an
argument for specifying the password identifier since that was used in
an old test vector. Now that that test vector has been updated, there is
no more need for this argument anymore. Simplify the older non-H2E case
to not pass through a pointer to the (not really used) password
identifier.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do so for both wpa_supplicant and hostapd. While this was not explicitly
required in IEEE P802.11az/D3.0, likely direction for the draft is to
start requiring use of H2E for all cases where SAE is used with PASN.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
