Instead of forcefully deinitializing ER immediately, give it some
time to complete unsubscription and call eloop_terminate() only once
ER code has completed its work.
WPA_TRACE=y builds will now verify that memory allocation in done
consistently using os_{zalloc,malloc,realloc,strdup,free} (i.e., no
mixing of os_* functions and unwrapper functions). In addition, some
common memory allocation issues (double-free, memory leaks, etc.) are
detected automatically.
WPA_TRACE=y can now be used to enable internal backtrace support that
will provide more details about implementation errors, e.g., when some
resources are not released correctly. In addition, this will print out
a backtrace automatically if SIGSEGV is received.
When setting up an AP with wpa_supplicant, the initial connection was
not necessarily setting oper state from DORMANT to UP which would be
blocking normal data frames. Fix this by initializing new_connection
to 1 so that even the first change to COMPLETED state will end up
setting oper state.
Replace driver wrapper calls to hostapd_tx_status(),
hostapd_rx_from_unknown_sta(), hostapd_mgmt_rx(), and
hostapd_mgmt_tx_cb() with new generic driver events
EVENT_TX_STATUS, EVENT_RX_FROM_UNKNOWN, and EVENT_RX_MGMT.
This cleans up lot of the driver wrapper code to be less dependent
on whether it is being used within wpa_supplicant AP mode or hostapd.
The Prism54.org project seems have been dead for a while and it does not
look like this driver would ever be maintained again. Furthermore, it is
difficult to find a version that would work with the driver_prism54.c
wrapper and there is another driver for these card in the Linux kernel
tree.
The hostapd integration in driver_prism54.c is quite different from the
other driver wrappers and would require major effort to get it cleaned
up. Since there does not seem to be any real users for the cleaned up
version, there does not seem to be justification to spend this effort on
the wrapper. This old code is making it much more difficult to clean up
the driver interface and at this point, the best option seems to be to
remove the driver wrappers. Should someone really still need this, the
old code will continue to be available in hostapd 0.6.x.
Instead of using the latest selected registrar change, collect selected
registrar information separately from all registrars and use the union
of this information when building the WPS IE for Beacon and Probe
Response frames.
Note: SetSelectedRegistrar UPnP action does not include a unique
identifier, so the ER matching routine is based only on the IP address
of the ER. In theory, there could be multiple ERs using the same IP
address (but different port or URL), so there may be some corner cases
that would not always match the correct ER entry at the AP. Anyway, this
is not really expected to occur in normal use cases and even if it did
happen, the selected registrar information is not any worse than it was
before when only the last change from any registrar for being
advertized.
In addition to the bitrate, the only other variable in this structure
is used internally in hostapd. Move this structure into hostapd.h and
make the driver API use simpler data structure (array of bitrates).
The following defines are not really needed in most places, so
remove them to clean up source code and build scripts:
EAP_TLS_FUNCS
EAP_TLS_OPENSSL
EAP_TLS_GNUTLS
CONFIG_TLS_INTERNAL
Wait for connection (IBSS join completed) event before marking state
completed. In addition, do not use the station mode authentication
timeout since that can trigger full disconnection from IBSS when
there is a timeout with just one of the peers.
Initialize the new DBus API before the old one, so new applications
which can use both, the old and the new API will be notified first
that new API is available.
cfg80211/mac80211 can get into somewhat confused state if the AP only
disassociates us and leaves us in authenticated state. For now, force
the state to be cleared with deauthentication to avoid confusing errors
if we try to associate with the AP again. This gets rid of 30 second
delay (scan timeout) in cases where only a disassociation frame is
received from the AP.
8a5ab9f5e5 fixed global driver context
for init2(), but it also broke driver initialization with driver
wrappers that do not use init2().. Fix this by setting wpa_s->global
before it gets dereferenced.
In addition, start ordering header file includes to be in more
consistent order: system header files, src/utils, src/*, same
directory as the *.c file.
This makes it clearer which files are including header from src/common.
Some of these cases should probably be cleaned up in the future not to
do that.
In addition, src/common/nl80211_copy.h and wireless_copy.h were moved
into src/drivers since they are only used by driver wrappers and do not
need to live in src/common.
This avoids passing the raw scan results into the RSN code and by
doing so, removes the only dependency on src/drivers from the
src/rsn_supp code (or from any src subdirectory for that matter).
Use shared functions for converting Primary Device Type between binary
and string formats. In addition, use array of eight octets instead of a
specific structure with multiple fields to reduce code complexity.
This gets rid of previously deprecated driver_ops handlers set_wpa,
set_drop_unencrypted, set_auth_alg, set_mode. The same functionality
can be achieved by using the init/deinit/associate handlers.
These driver wrappers should not be used anymore; WEXT should be used
instead. However, there may still be users stuck on older kernel versions
that may require driver specific wrappers, so the source code still
remains in the repository.
Clean up driver interface by merging hostapd and wpa_supplicant
specific set_beacon driver_ops into a single one. In addition,
merge set_beacon_int into to the same operation.
This removes many of the cases where moving to the WPS tab can be
undesired. It is really only useful if we are not currently connected
and there is an AP available that would likely be able to provide us
network connectivity with use of WPS (active PBC more or selected
registrar set).
Clean up the peer dialog information to be more user friendly. Only
show the device type in the tooltip and move the verbose details into
a separate area in a new Properties dialog. The new dialog will also
show some of the standard fields with titles to make them easier to
read.
The Enrollee entry may be deleted while the PIN query dialog is open.
To avoid crashing on using freed entry, copy the needed data into
local variables before and use the local data after the PIN dialog
has been closed.
The peer entries are now using different icons based on their type. As
a starting point, a separate AP and laptop icons are used. More icons may
be added in the future to mark different device types (e.g., based on
primary device type information from WPS).
When using umask 0077, the control interface directory was left without
group read/execute permissions even if the configuration file explicitly
asked for the group to be allowed to access the control interface. Fix
this by adding read/execute permissions for group if a specific group is
defined in the configuration. [Bug 199]
Change the dbus policy file to only allow root applications to receive
signals from wpa_supplicant. This keeps WPS Credentials data secret
from non-root listeners.
When trying to build wpa_gui (Qt4 version) from openembedded it fails
because Qt4 is compiled without session manager and thus wpa_gui fails
to compile.
I attached a patch, that enables compiling without Session Manager (via
preprocessor) if it is not compiled into Qt4; otherwise, it behaves as
it does right now.
I checked to build on my host (Debian unstable, Session Manager
enabled) and openembedded (Session Manager disabled).
This will need some additional code in wps_er_pbc() to handle PBC mode
enabling for a single AP only. For now, this can only be expected to work
when the ER is connected to a single AP.
Clean up registration of large number of dbus method/property/signal
handlers by using arrays containing all the information needed to call
the registration functions.
New PINs can now be added to WPS ER. This results in the ER code
using SetSelectedRegistrar to modify AP state so that Enrollees
will be able to notice the actice registrar more easily.
Smartcard parameter update via DBus ended up re-initializing the EAPOL
state machine without updating the pointer inside WPA state machine.
This can trigger a segfault when EAP layer attempts to use the old
reference. Fix this by re-initializing the pointer inside WPA state
machine.
Better make sure we do not end up writing over the end of the local
registered_sig buffer regardless of how many arguments are used in
dbus method description.
There is no point checking whether wpa_s is not NULL after having
dereferenced it earlier in the function.. Furthermore, there is no
need to use a local variable for wpas_dbus_get_path() result.
The cleanup routine in the end would have dereferenced props pointer
which could be NULL. There is no need to go through that cleanup code
in this case, so just exit from the function with return instead.
ssid could be NULL here at least based on the function documentation,
so better check whether that is the case prior to calling the
notification function.
Commit d3a9822542 broke per-SSID scan
by using the ssid variable for internal loop and by doing so,
overriding the value that was needed below to figure out whether the
scan is for a specific SSID. Fix this by using a temporary variable
instead when looping over network finding which frequencies to scan for.
This was triggering some gcc versions to warn about strict aliasing.
Since the typecast is not really needed here, the cleanest way to get
rid of the warnings is to just use the correct type for the local
variable.
This is like wpa_msg(), but the output is directed only to
ctrl_interface listeners. In other words, the output will not be
shown on stdout or in syslog.
Change scan result reporting to use wpa_msg_ctrl() for
CTRL-EVENT-SCAN-RESULTS message at info level and wpa_printf() at
debug level to avoid showing scan result events in syslog in the
common configuration used with NetworkManager.
This patch implements the new DBus API. Both, the new and the
previous API may work concurrently and may be turned on or off
separately in .config file.
Some features of the new API are:
- more wpa_supplicant's events are signaled with DBus signals,
- introspection data (requires libxml2 and may be disabled),
- CurrentBSS and CurrentNetwork properties,
- PropertyChanged signal for most of properties,
- Relatively easy to extend.
.config options for the new API are: CONFIG_CTRL_IFACE_DBUS_NEW=y and
CONFIG_CTRL_IFACE_DBUS_INTRO=y for introspection.
This commit misses couple of parts from the full implementation
(these are still under review):
- fetching all configuration parameters for learning WPS information
- scan result BSS add/remove notification (register_bss() and
unregister_bss() notification callbacks)
Clean up code so that UPnP implementation does not need to include all
the HTTP functionality. In addition, make it easier to share HTTP server
functionality with other components in the future.
Instead of implementing HTTP client functionality inside
wps_upnp_event.c, use a generic HTTP client module to do this. The HTTP
client code can now be shared more easily for other purposes, too.
This is the first step in adding support for using wpa_supplicant as a
WPS External Registrar to manage APs over UPnP. Only the device
discovery part is implemented in this commit.
New wpa_supplicant command line options -o<driver> and -O<ctrl> can
now be used to override the parameters received in add interface
command from dbus or global ctrl_interface. This can be used, e.g.,
to enable control interface when using NetworkManager (add
-O/var/run/wpa_supplicant into the Exec parameter in
/usr/share/dbus-1/system-services/fi.epitest.hostap.WPASupplicant.service).
Similarly, this can be used to use another driver wrapper with
NetworkManager (e.g., -onl80211 to replace WEXT with nl80211).
This provides information about PBC mode result from the WPS Registrar
module. This could be used, e.g., to provide a user notification on the
AP UI on PBC failures.
Force deauthentication from the AP to clear mac80211 state (it would get
stuck with future scans if the AP is left in authenticated, but not
associated, state).
Add blacklist entry for the AP to allow other APs with worse signal
strength to be tried (e.g., when APs are trying to do load balancing
with status code 17). Reduce wait for the next scan to speed up
connection in cases where there could be other APs that could accept
association, but which show worse signal strength.
This functionality fits better with src/tls (i.e., internal TLS
implementation), so move it there to make crypto_internal.c more
of a wrapper like other crypto_*.c files.
Previously, APs that were hiding SSID (zero-length SSID IE in
Beacon frames) could have been selected when wildcard SSID matching
was used. This would result in failed association attempt since
the client does not know the correct SSID. This can slow down WPS
which is often using wildcard SSID matching.
Ignore BSSes without known SSID in the scan results when selecting
which BSS to use.
This patch completely separates supplicant's code from dbus.
It introduces three new notifications which copes with all
remaining dbus stuff.
wpas_notify_unregister_interface() was renamed to
wpas_notify_iface_removed().
The hostapd/wpa_supplicant compilation failed with CONFIG_IEEE80211R=y
or CONFIG_IEEE80211W=y option if CONFIG_EAP_PSK and CONFIG_EAP_GPSK are
not used.
mac80211 does not currently allow (re)authentication when we are already
authenticated. In order to work around this, force deauthentication if
nl80211 authentication command fails with EALREADY. Unfortunately, the
workaround code in driver_nl80211.c alone is not enough since the
following disconnection event would clear wpa_supplicant authentication
state. To handle this, add some code to restore authentication state
when using userspace SME.
This workaround will hopefully become unnecessary in some point should
mac80211 start accepting new authentication requests even when in
authenticated state.
Reorganize the TLS/crypto library segments into a single set of blocks
for each library instead of multiple locations handling library-specific
operations. Group crypto functionality together and get wpa_supplicant
and hostapd Makefile closer to eachother in order to make it easier to
eventually move this into a shared makefile.
Crypto library wrappers can now override the internal DH (group 5)
implementation. As a starting point, this is done with OpenSSL. The
new mechanism is currently available only for WPS (i.e., IKEv2 still
depends on the internal DH implementation).
Whenever running wpa_supplicant in AP mode with WPS enabled, the
notifications of missing WPS PIN are now shown on the peer dialog
to make it easier to provide the PIN.
If no BSSes/IBSSes matching the enabled networks are found in the scan
results, IBSS/AP mode network (if configured) can be created in
ap_scan=1 mode instead of requiring ap_scan=2 mode to be used whenever
using IBSS or AP mode.
This brings in the first step in adding support for using NSS
(Mozilla Network Security Services) as the crypto and TLS library
with wpa_supplicant. This version is able to run through EAP-PEAP
and EAP-TTLS authentication, but does not yet implement any
certificate/private key configuration. In addition, this does not
implement proper key fetching functions either, so the end result
is not really of much use in real world yet.
Current wpa_supplicant has a bug with WEP keys, it adds a zero-length
sequence counter field to netlink which the kernel doesn't accept.
Additionally, the kernel API slightly changed to accept keys only when
connected, so we need to send it the keys after that. For that to work
with shared key authentication, we also include the default WEP TX key
in the authentication command.
To upload the keys properly _after_ associating, add a new flag
WPA_DRIVER_FLAGS_SET_KEYS_AFTER_ASSOC_DONE indicating that the driver
needs the keys at that point and not earlier.
This allows background scanning and roaming decisions to be contained in
a single place based on a defined set of notification events which will
hopefully make it easier to experiment with roaming improvements. In
addition, this allows multiple intra-ESS roaming policies to be used
(each network configuration block can configure its own bgscan module).
The beacon loss and signal strength notifications are implemented for
the bgscan API, but the actual events are not yet available from the
driver.
The included sample bgscan module ("simple") is an example of what can
be done with the new bgscan mechanism. It requests periodic background
scans when the device remains associated with an ESS and has couple of
notes on what a more advanced bgscan module could do to optimize
background scanning and roaming. The periodic scans will cause the scan
result handler to pick a better AP if one becomes available. This bgscan
module can be taken into use by adding bgscan="simple" (or
bgscan="simple:<bgscan interval in seconds>") into the network
configuration block.
After transitioning from DISCONNECTED to SCANNING, we never go back
to DISCONNECTED even though scanning is done or failed.
We're thus stuck in SCANNING while scanning is actually done.
Convert wpa_supplicant_get_scan_results_old() to use the same return
style with the other get_scan_results options and clean up the code
by sharing the same scan result freeing and error checking code for
all the options.
Instead of implementing these separately in various control
interface handlers, use shared functions. These add some of the
previously missing notification calls, too, for the affected areas.
This introduces a new mechanism for collecting notification calls into
a single place (notify.c). As a result of this, most of the
wpa_supplicant code does not need to know about dbus (etc. mechanisms
that could use the notifications). Some empty placeholder functions are
also added in preparation of new dbus code that needs more event
notifications.
In addition, add a peer entry type for each peer entry. Currently,
this is only stored as an integer and visible in the context menu.
Eventually, different icons should be used based on this type.
This provides some initial functionality for showing peer information,
i.e., showing information about other devices that has been discovered.
Currently, information is only available in the AP mode (list of
associated stations), but this is expected to increase in the future
(e.g., show the current AP in station mode, other stations in IBSS,
etc.). Furthermore, there will be actions available for doing things
like providing a WPS PIN for a station.
wpa_supplicant can now reconfigure the AP by acting as an External
Registrar with the wps_reg command. Previously, this was only used
to fetch the current AP settings, but now the wps_reg command has
optional arguments which can be used to provide the new AP
configuration. When the new parameters are set, the WPS protocol run
is allowed to continue through M8 to reconfigure the AP instead of
stopping at M7.
If an EAPOL frame is received while wpa_supplicant thinks the driver is
not associated, queue the frame for processing at the moment when the
association event is received. This is a workaround to a race condition
in receiving data frames and management events from the kernel.
The pending EAPOL frame will not be processed unless an association
event is received within 100 msec for the same BSSID.
wpa_supplicant can now be built with FIPS capable OpenSSL for FIPS mode
operation. Currently, this is only enabling the FIPS mode in OpenSSL
without providing any higher level enforcement in wpa_supplicant.
Consequently, invalid configuration will fail during the authentication
run. Proper configuration (e.g., WPA2-Enterprise with EAP-TLS) allows
the connection to be completed.
An SMC router was reported to use 0x22 (WPAPSK + WPA2PSK) in the
authentication type of the provisioned credential and wpa_supplicant
rejected this as invalid. Work around this by replacing WPAPSK + WPA2PSK
with WPA2PSK.
This is a (hopefully) temporary workaround to allow the same source code
tree to be used for building hostapd and wpa_supplicant without having
to manually force recompilation of some files. Currently, some of the
driver wrapper files need to be built separately for hostapd and
wpa_supplicant (#ifdef's in the files based on AP functionality).
This is somewhat racy as far as parallel make execution is concerned,
i.e., it may be necessary to run "make -j#" twice (plain "make" works
fine. Since this is supposed to be a temporary workaround, there is not
much point in trying to fix this with any more complex make processing.
Instead of having all driver stuff collected across wpa_supplicant
and hostapd, create a common snippet that they both include and
that handles the build configuration.
Change existing CONFIG_LIBNL20 compatibility code in
driver_nl80211.c to be used by both wpa_supplicant
and hostapd, but take care of nl_handle too now.
Propagate CONFIG_LIBNL20 out of .config file and onto
CFLAGS in the Makefile.
Use libnl-gen now too.
Signed-off-by: Jon Loeliger <jdl@bigfootnetworks.com>
---
Since we do not currently support changing the AP settings received
from M7, there is no point in actually sending out the M8 that would
likely trigger the AP to reconfigure itself and potentially reboot.
For now, we just receive the AP settings in M7 and add a local network
configuration block based on those, but NACK the message. This makes
wps_reg work like wps_pin, but by using the AP PIN instead of a client
PIN.
When the supplicant is connected and performs a scan, it doesn't enter
WPA_SCANNING state for various reasons. However, external programs
still need to know that the supplicant is scanning since they may not
wish to perform certain operations during a scan (as those operations
will likely fail or yield incorrect results). Add a 'scanning' property
and signal to the supplicant dbus interface to allow clients to
synchronize better with the supplicant when it scans.
Signed-off-by: Dan Williams <dcbw@redhat.com>
hostapd_cli wps_pin command can now have an optional timeout
parameter that sets the PIN lifetime in seconds. This can be used
to reduce the likelihood of someone else using the PIN should an
active PIN be left in the Registrar.
I've exported the methods wpsPbc, wpsReg and wpsPin (patch attached),
so wpa_supplicant should be able to connect with WPS using the dbus
interface. I couldn't test it well because the problem seems to be in
my wireless card, a Broadcom BCM4328. At least it seems to do the same
using both interfaces. With ndiswrapper driver the "wpsie" entry
(thanks Dan!) didn't appear, and with the Broadcom wl driver it
appears but I cannot associate using WPS.
Add a new DBus method "setDebugParams" which takes the parameters
debug_level, debug_timestamp and show_keys as input and updates the
internal debug variables accordingly.
To change the debug level, enable/disable timestamps and enable/disable
show_keys the following dbus-send command can be used:
dbus-send --system --dest=fi.epitest.hostap.WPASupplicant --print-reply
/fi/epitest/hostap/WPASupplicant fi.epitest.hostap.WPASupplicant.setDebugParams
int32:0 boolean:false boolean:false
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
When in AP mode, wpa_supplicant is now enabling WPS (only Internal
Registrar). wpa_cli wps_pbc and wps_pin commands can be used to initiate
WPS negotiation similarly to how this is done in station mode (though,
the BSSID parameter is ignored).
There is no point in trying to continue if a 4-way handshake frame is
discarded or if PTK/GTK/IGTK configuration fails. Force the client to
disconnect in such a case to avoid confusing user by claiming the
connection was successfully completed.
Use a parameter structure to pass in information that can be more easily
extended in the future. Include some of the parameters that were
previously read directly from hapd->conf in order to reduce need for
including hostapd/config.h into driver wrappers.
This merges the driver wrapper implementations to use the same
implementation both for hostapd and wpa_supplicant operations to avoid
code duplication.
This commit merges the driver_ops structures and implementations from
hostapd/driver*.[ch] into src/drivers. This is only an initial step and
there is room for number of cleanups to share code between the hostapd
and wpa_supplicant parts of the wrappers to avoid unnecessary source
code duplication.
Need to set WEP keys before requesting authentication in order to get
Shared Key authentication working. Previously, the WEP keys were not set
at all when using SME in wpa_supplicant.
IEEE 802.11r KDF uses key length in the derivation and as such, the PTK
length must be specified correctly. The previous version was deriving
using 512-bit PTK regardless of the negotiated cipher suite; this works
for TKIP, but not for CCMP. Update the code to use proper PTK length
based on the pairwise cipher.
This fixed PTK derivation for both IEEE 802.11r and IEEE 802.11w (when
using AKMP that specifies SHA-256-based key derivation). The fixed
version does not interoperate with the previous versions. [Bug 307]
Update credential to only include a single authentication and
encryption type in case the AP configuration includes more than one
option. Without this, the credential would be rejected if the AP was
configured to allow more than one authentication type.
A new network block parameter, scan_freq, can be used to specify subset
of frequencies to scan. This can speed up scanning process considerably
if it is known that only a small subset of channels is actually used in
the network. A union of configured frequencies for all enabled network
blocks is used in scan requests.
Currently, only driver_nl80211.c has support for this functionality.
For example, following parameter marks 2.4 GHz channels 1, 6, 11 to be
scanned: scan_freq=2412 2437 2462
wpa_supplicant can now initialize hostapd data structures when mode=2 is
used to set up an AP. The hostapd configuration is not yet set based on
wpa_supplicant network configuration block. In addition, the glue code
for hostapd driver_ops needs number of functions that will be needed for
AP functionality.
Move the shared IEEE 802.11w enum definition into src/common/defs.h to
avoid redefinition when both configuration structures are included into
the same file.
This version is adding the configuration option (mode=2) for this and
driver capability reporting to figure out whether AP mode can be used.
However, this does not actually implement any real functionality yet.
All these driver handlers can be implemented in associate() handler
which gets all the needed information in the parameters structure. The
old functions that provided only a single parameter will be removed
eventually to clean up the driver_ops structure, so driver wrappers
should start using the newer mechanism.
Removing just sun_family is not portable since some systems (e.g.,
FreeBSD) include an additional sun_len field. Using offsetof should be
portable. In addition, set sun_ken for FreeBSD.
This can be used, e.g., with mac80211-based Linux drivers with
nl80211. This allows over-the-air FT protocol to be used (IEEE
802.11r).
Since the nl80211 interface needed for this is very recent (added
today into wireless-testing.git), driver_nl80211.c has backwards
compatibility code that uses WEXT for association if the kernel does
not support the new commands. This compatibility code can be
disabled by defining NO_WEXT_COMPAT. That code will also be removed
at some point to clean up driver_nl80211.c.
This adds first part of FT resource request as part of Reassocition
Request frame (i.e., FT Protocol, not FT Resource Request Protocol).
wpa_supplicant can generate a test resource request when driver_test.c
is used with internal MLME code and hostapd can verify the FTIE MIC
properly with the included RIC Request.
The actual RIC Request IEs are not processed yet and hostapd does not
yet reply with RIC Response (nor would wpa_supplicant be able to
validate the FTIE MIC for a frame with RIC Response).
This is done with wired interfaces to fix IEEE 802.1X authentication
when the authenticator uses the group address (which should be happening
with wired Ethernet authentication).
This allows wpa_supplicant to complete wired authentication successfully
on Vista with a NDIS 6 driver, but the change is likely needed for
Windows XP, too.
Do not use just the driver name for this since driver_ndis.c supports
both wired and wireless NDIS drivers and needs to indicate the driver
type after initialization.
Calculate the estimated medium time using integer variables since there
is no real need to use floating point arithmetics here. In addition,
make sure there is no division by zero regardless of how invalid the
request from the station is. Reject invalid parameters and refuse
requests that would take most of the bandwidth by themselves.
Add test code into wpa_supplicant mlme.c to allow WMM-AC negotiation to
be tested with driver_test.
The new file wps_nfc.c and ndef.c implements NFC device independent
operation, wps_nfc_pn531.c implements NFC device dependent operation.
This patch is only for the following use case:
- Enrollee = wpa_supplicant
- Registrar = hostapd internal Registrar
Following NFC methods can be used:
- Enrollee PIN with NFC
- Registrar PIN with NFC
- unencrypted credential with NFC
Encrypted credentials are not supported.
Enrollee side operation:
Registrar side operation:
Example configuration.
CONFIG_WPS=y
CONFIG_WPS_NFC=y
CONFIG_WPS_NFC_PN531=y
I used NFC device "NXP PN531". The NFC device access method is
confidential, so I used outer library. Please download below files from
https://www.saice-wpsnfc.bz/index.php
[WPS NFC Library]
WpsNfcLibrary/WpsNfc.h
WpsNfcLibrary/WpsNfcType.h
WpsNfcLibrary/WpsNfcVersion.h
WpsNfcLibrary/linux/libnfc_mapping_pn53x.dll
WpsNfcLibrary/linux/wpsnfc.dll
[NFC Reader/Writer Kernel Driver]
NFCKernelDriver-1.0.3/linux/kobj/sonyrw.ko
<WiFi test>
The hostapd/wpa_supplicant with this patch passed below tests on
"Wi-Fi WPS Test Plan Version 1.6".
4.2.5 Add device using NFC Method with password token
(I used SONY STA instead of NXP STA.)
4.2.6 Add device using NFC Method with configuration token
5.1.9 Add to AP using NFC Method with password token
through internal registrar
(I used SONY AP instead of NXP AP.)
5.1.10 Add to AP using NFC Method with configuration token
through internal registrar
Many deployed APs do not handle negotiation of security parameters well
when both TKIP and CCMP (or both WPA and WPA2) are enabled. The most
common end result seems to be ending up with the least secure option..
As a workaround, check whether the AP advertises WPA2/CCMP in Beacon
frames and add those options for the credential if needed. This allows
the client to select the most secure configuration regardless of how
broken the AP's WPS implementation is as far as auth/encr type
negotiation is concerned.
The old behavior of generating new DH keys can be maintained for non-OOB
cases and only OOB (in this case, with UFD) will use the pre-configured
DH keys to allow the public key hash to be checked.
Not all embedded devices have USB interface and it is useful to be able
to remove unneeded functionality from the binary. In addition, the
current implementation has some UNIX specific calls in it which may make
it not compile cleanly on all target systems.
It seems that WFA WPS spec says that default key index should be 1 (not
0). I think this meas that WEP key indexes region is not from 0 to 3,
but from 1 to 4 in WPS. At least WRT610N implemented it this way.
These flags are used to mark which values (level, noise, qual) are
invalid (not available from the driver) and whether level is using dBm.
D-Bus interface will now only report the values that were available.
If the driver reports support for more than one SSID per scan request,
optimize scan_ssid=1 operations in ap_scan=1 mode. This speeds up
scanning whenever scan_ssid=1 is used since the broadcast SSID can be
included in every scan request and if driver supports more than two
SSIDs in the scan request, the benefits are even larger when multiple
networks have been configured with ap_scan=1.
This is also cleaning up wpa_supplicant_scan() function by moving code
around so that the SSID list is not processed unnecessarily if the
operation mode does not need this.
This can be used to provide support for scanning multiple SSIDs at a
time to optimize scan_ssid=1 operations. In addition, Probe Request IEs
will be available to scan2() (e.g., for WPS PBC scanning).
For example, -Dnl80211,wext could be used to automatically select
between nl80211 and wext. The first driver wrapper that is able to
initialize the interface will be used.
The driver wrappers can now inform wpa_supplicant how many SSIDs can
be used in a single scan request (i.e., send multiple Probe Requests
per channel). This value is not yet used, but it can eventually be used
to allow a new scan command to specify multiple SSIDs to speed up
scan_ssid=1 operations. In addition, a warning could be printed if
scan_ssid=1 is used with a driver that does not support it
(max_scan_ssids=0).
Split the auth=none option into three: open, WEP, WEP with shared key to
allow the user specify WEP with shared key authentication. In addition,
fix static WEP key edits to be enabled only when using static WEP keys
(i.e., not for IEEE 802.1X).
wpa_supplicant should not send a dbus reply as response to a method call
if no reply was requested by the caller. Sending a reply even if not
requested is basically no problem but triggers dbus warnings like the
one below.
Feb 9 07:31:23 linux-gvjr dbus-daemon: Rejected send message, 2 matched
rules; type="error", sender=":1.129" (uid=0 pid=30228
comm="/usr/sbin/wpa_supplicant -c /etc/wpa_supplicant/wp")
interface="(unset)" member="(unset)" error
name="fi.epitest.hostap.WPASupplicant.InvalidInterface"
requested_reply=0 destination=":1.128" (uid=0 pid=30226
comm="/usr/sbin/NetworkManager "))
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Build EAP-WSC dynamically does not make much sense and with the
dependencies to WPS code from number of places resolving this is not
trivial. It is simpler to just remove this option.
If you don't choose OpenSSL as TLS implementation and choose to enable
CONFIG_EAP_TNC you have to link against libdl. The OpenSSL libraries
implicitly link against them, so this might be a reason why it wasn't
noticed yet. I assume the same applies to hostapd.
We can now handle up to 65535 byte result buffer which is the maximum
due to WEXT using 16-bit length field. Previously, this was limited to
32768 bytes in practice even through we tried with 65536 and 131072
buffers which we just truncated into 0 in the 16-bit variable.
This more or less doubles the number of BSSes we can received from scan
results.
If wpa_supplicant is started with -u but the DBus service is already
registered wpa_supplicant will bail out. However, it will segfault
in wpa_supplicant_deinit because global->drv_priv wasn't allocated
yet.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
This is based on a patch from Pavel Roskin <proski@gnu.org>, but with
the WIRELESS_DEV part removed instead of moved since it does not apply
anymore. Additional note on client MLME limitations was also added.
MadWifi is unlikely to be in ../head relative to hostapd or
wpa_supplicant, as it would be inside the hostap git repository.
MadWifi sources are more likely to be in a directory called "madwifi"
and residing outside the hostap repository. Using "madwifi" also
demonstrates that the top-level madwifi directory is needed.
If a Registrar tries to configure the AP, but fails to validate the
device password (AP PIN), lock the AP setup after four failures. This
protects the AP PIN against brute force guessing attacks.
Some WPS APs do not set Selected Registrar attribute to 1 properly when
using an external Registrar. Allow such an AP to be selected for PIN
registration after couple of scan runs that do not find APs marked with
Selected Registrar = 1. This allows wpa_supplicant to iterate through
all APs that advertise WPS support without delaying connection with
implementations that set Selected Registrar = 1 properly.
The default interval is now 5 seconds (used to be 1 second for
interactive mode and 2 seconds for wpa_cli -a). The interval can be
changed with -G<seconds> command line option.
The separate Association Comeback Time IE was removed from IEEE 802.11w
and the Timeout Interval IE (from IEEE 802.11r) is used instead. The
editing on this is still somewhat incomplete in IEEE 802.11w/D7.0, but
still, the use of Timeout Interval IE is the expected mechanism.
The wps_cred_process option can be used to configure wpa_supplicant to
send received Credential attributes for external processing over
ctrl_iface and dbus. This allows external programs to update their
configuration when WPS is used to provision new networks.
This makes it easier to pass the credential data to external programs
(e.g., Network Manager) for processing. The actual use of this data is
not yet included in hostapd/wpa_supplicant.
The current implementation does not support WPA/WPA2-Enterprise
credentials. Ignore any credential that is using unsupported
authentication type to avoid potential issues with partially configured
network blocks.
Must not set pairwise_cipher/group_cipher for non-WPA/WPA2 networks
since the configuration parser is going to reject such values. In
addition, should not limit group_cipher to just TKIP or TKIP|CCMP just
in case the AP is using WEP as the group cipher. Default group_cipher
value can be used for all cases.
RSN IBSS uses authentication per-STA and that is initialized separately,
so there is no need to enable the per-BSS like authentication that is
used with APs.
This makes wpa_gui remember whether it was only in the tray when the
session was terminated and starts only in the tray if session manager
restarts it automatically.
This commit adds a new build option, CONFIG_IBSS_RSN=y, that can be used
to enable RSN support for IBSS. This links in RSN Authenticator code
from hostapd and adds code for managing per-peer information for IBSS. A
new wpa_cli command or driver event can be used to request RSN
authentication with an IBSS peer. New RSN Authenticator and Supplicant
will be allocated for each peer.
The basic state machine setup code is included in this commit, but the
state machines are not properly started yet. In addition, some of the
callback functions are not yet complete.
Do not add the automatically generated RADIUS attributes NAS-IP-Address,
Calling-Station-Id, Framed-MTU, NAS-Port-Type, and Connect-Info if -N
option is used with the same attribute type. This allows these
attributes to be replaced without causing duplicate entries.
Fix compile warning by renaming gridLayout to wpsGridLayout in
wpagui.ui, it seems to be used internally.
/usr/bin/uic-qt4 eventhistory.ui -o .ui/ui_eventhistory.h
/usr/bin/uic-qt4 scanresults.ui -o .ui/ui_scanresults.h
/usr/bin/uic-qt4 wpagui.ui -o .ui/ui_wpagui.h
Warning: name gridLayout is already used
/usr/bin/uic-qt4 userdatarequest.ui -o .ui/ui_userdatarequest.h
/usr/bin/uic-qt4 networkconfig.ui -o .ui/ui_networkconfig.h
Also disable WPS tab if the running supplicant doesn't support that,
just as the WPS action menu is.
Signed-off-by: Kel Modderman <kel@otaku42.de>
It is better to have command description around the command definitions:
the chances for omitting usage, forgotting to change/delete them, etc.
are smaller than for the separate usage statement. [Bug 290]
Signed-off-by: Eygene Ryabinkin <rea-fbsd@codelabs.ru>
I had added flags to the every command description: just now the only
meaningful flag tells that this command has sensitive arguments and it
shouldn't be written to the disk. I rewrote the logics for the search
for the sensitive commands: special procedure is now loops over all
commands and tries to see if command has sensitive data. [Bug 289]
Signed-off-by: Eygene Ryabinkin <rea-fbsd@codelabs.ru>
First of all, the history had not been written to the disk, since almost
all commands were cleaned up due to the error in the history cleaning:
the return value of the last os_strncasecmp() call was not compared to
zero, but was rather used as is. So the condition was almost always
true and most commands were removed from the history.
The second problem was that the evaluation of the potentially sensitive
commands was started at the entry number 1, instead of very first entry.
This change replaces -I and -i options (Chargeable-User-Identity) with a
new -N option that can add any RADIUS attribute into the Access-Request
messages without having to modify eapol_test for each new attribute.
Replace " wpa_supplicant" with " %wpa_supplicant" except for
"struct wpa_supplicant". This makes it easier to write Doxygen comments
since there is no need to add the ugly '%' prefix to each instance of
wpa_supplicant text showing up.
This updated all doxygen runs to use the same style that was used for
wpa_supplicant full documents. The full vs. fast configurations are now
otherwise identical apart from fast not generating dot files or
latex/pdf version of the documentation.
Generate a SHA1 hash -based UUID from the local MAC address if the UUID
was not configured. This makes it easier to prepare for WPS since there
is no need to generate an UUID.
When using ap_scan=1, we know before the association request that MFP
will be supported, so we can as well require it. This helps mac80211 in
configuring whether to enable MFP.
This commit changes just the name and Action category per D7.0. The
retransmit/timeout processing in the AP is not yet updated with the
changes in D7.0.
It seems that for WPS registration we should use the same authentication
timeout as for ieee8021x, no? (See patch attached.) On slow platforms
public keys computation may take around 4-5 seconds (we actually stuck
on this issue).
Set ctrl_interface to non-empty value in INTERFACE_ADD to avoid
ctrl_iface.c assuming the control interface is not to be enabled. This
fixes the dynamically added interface to use control interface.
The NSIS installer will now add Windows registry entries for
wpa_supplicant during installation and removes them during
uninstallation. This allows wpa_gui to start wpasvc and add new
interfaces without requiring the user to do any manual registry
editing.
"Add interface" command in File menu can now be used to add a new
network interface to running wpa_supplicant (using INTERFACE_ADD control
interface command). In addition, the network interface is added into
Windows registry (with skip_on_error) for future use. This functionality
is currently enabled only for Windows builds. The user is also prompted
about the possibility of adding an interface if no interfaces are
enabled. This makes it easier to get started without having to touch
registry manually.
This can be used to include binding information for multiple interfaces
in Windows registry and only use the ones that match with an available
network interface.
The new INTERFACE_LIST global control interface command can be used to
request a list of all available network interfaces that could be used
with the enabled driver wrappers. This could be used to enable
interfaces automatically by external programs (e.g., wpa_gui).
Driver wrappers can now register global_init() and global_deinit()
driver_ops handlers to get a global data structure that can be shared
for all interfaces. This allows driver wrappers to initialize some
functionality (e.g., interface monitoring) before any interfaces have
been initialized.
UUID-E is not required to be present in Beacon frame, so we need to
accept scan results that do not have UUID-E as a valid PBC situation as
long as not more than one AP is in active PBC mode.
wpa_gui will now ask user whether the wpasvc service should be started
if it is not running. In addition, File menu has items for starting and
stopping the service.
Change association behavior to match with ap_scan=1 when WPS is used in
ap_scan=2 mode with wildcard SSID matching. In addition, allow hardcoded
BSSID to be used to select AP even if selected registrar attribute is
not present.
A separate cross compiler mkspecs file (win32-x-g++) is now used to
configure all build options so the setup-mingw-cross-compiling hack is
not needed anymore. Furthermore, the MinGW setup is now on path, so no
need to specify extra PATH changes for it.
This callback is now used to stop wpa_supplicant from trying to continue
using parameters (most likely, device password) that do not work in a
loop. In addition, wpa_gui can now notify user of failed registration.
The event callback will be used for various event messages and the M2D
notification is the first such message. It is used to notify wpa_gui
about Registrar not yet knowing the device password (PIN).
We need to be a bit more careful when removing the WPS configuration
block since wpa_s->current_ssid may still be pointing at it. In
addition, registrar pointer in wps_context will need to be cleared
since the context data is now maintained over multiple EAP-WSC runs.
Without this, certain WPS operations could have used freed memory.
The specific AP (BSSID) can now be selected through scan results for
WPS (WPS pushbutton on the network configuration dialog). When a BSSID
is selected, AP device PIN (e.g., from a label) can be used to configure
the AP by acting as a Registrar.
Whenever new scan results include WPS AP(s) and the client is not
associated, send a notification message to control interface monitors.
This makes it easier for GUIs to notify the user about possible WPS
availability without having to go through the scan results.
Windows Server 2008 NPS gets very confused if the TLS Message Length is
not included in the Phase 1 messages even if fragmentation is not used.
If the TLS Message Length field is not included in ClientHello message,
NPS seems to decide to use the ClientHello data (excluding first six
octets, i.e., EAP header, type, Flags) as the OuterTLVs data in
Cryptobinding Compound_MAC calculation (per PEAPv2; not MS-PEAP)..
Lets add the TLS Message Length to PEAPv0 Phase 1 messages to get rid of
this issue. This seems to fix Cryptobinding issues with NPS and PEAPv0
is now using optional Cryptobinding by default (again) since there are
no known interop issues with it anymore.
Changed peer to derive the full key (both MS-MPPE-Recv-Key and
MS-MPPE-Send-Key for total of 32 octets) to match with server
implementation.
Swapped the order of MPPE keys in MSK derivation since server
MS-MPPE-Recv-Key | MS-MPPE-Send-Key matches with the order specified for
EAP-TLS MSK derivation. This means that PEAPv0 cryptobinding is now
using EAP-MSCHAPv2 MSK as-is for ISK while EAP-FAST will need to swap
the order of the MPPE keys to get ISK in a way that interoperates with
Cisco EAP-FAST implementation.
driver_test can now be used either over UNIX domain socket or UDP
socket. This makes it possible to run the test over network and makes it
easier to port driver_test to Windows.
hostapd configuration: test_socket=UDP:<listen port>
wpa_supplicant configuration: driver_param=test_udp=<dst IP addr>:<port>
This adds support for setting of a regulatory domain to wpa_supplicant
drivers. It also adds regulatory domain setting for the nl80211 driver.
We expect an ISO / IEC 3166 alpha2 in the wpa configuration file as a
global.
Print the password field only if -K is given by using wpa_hexdump_ascii_key
instead of wpa_hexdump_ascii. Additionally mark the password field as key.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
This is just making an as-is copy of EAP-AKA server and peer
implementation into a new file and by using the different EAP method
type that is allocated for EAP-AKA' (50). None of the other differences
between EAP-AKA and EAP-AKA' are not yet included.
It is likely that once EAP-AKA' implementation is done and is found to
work correctly, large part of the EAP-AKA and EAP-AKA' code will be
shared. However, it is not reasonable to destabilize EAP-AKA
implementation at this point before it is clearer what the final
differences will be.
Previously, this was only done when the new connection is using
WPA-Personal. However, it looks like it was possible to trigger an
infinite busy loop if altAccept or altReject were left set to true and
an EAPOL frame is received (eapolEap is set to true). Clearing altAccept
and altReject for each association prevents this loop from happening in
the beginning of the next association.
Fragment WPS IE if needed to fit into the IE length limits in hostapd
and Reassemble WPS IE data from multiple IEs in wpa_supplicant.
In addition, moved WPS code from events.c into wps_supplicant.c to clean
up module interfaces.
New control interface commands WPS_PBC, WPS_PIN, and WPS_REG can be used
to start WPS processing. These add and select the WPS network block into
the configuration temporarily, i.e., there is no need to add the WPS
network block manually anymore.
The wps_context data is now managed at wpa_supplicant, not EAP-WSC. This
makes wpa_supplicant design for WPS match with hostapd one and also
makes it easier configure whatever parameters and callbacks are needed
for WPS.
Previously, wpa_supplicant as Enrollee case was handled using a
different callback function pointer. However, now that the wps_context
structure is allocated for all cases, the same variable can be used in
all cases.
This cleans up the internal interface between different modules and is
the first step in getting wpa_supplicant design closer to hostapd as far
as WPS is concerned.
This adds WPS support for both hostapd and wpa_supplicant. Both programs
can be configured to act as WPS Enrollee and Registrar. Both PBC and PIN
methods are supported.
Currently, hostapd has more complete configuration option for WPS
parameters and wpa_supplicant configuration style will likely change in
the future. External Registrars are not yet supported in hostapd or
wpa_supplicant. While wpa_supplicant has initial support for acting as
an Registrar to configure an AP, this is still using number of hardcoded
parameters which will need to be made configurable for proper operation.
It looks like some Windows NDIS drivers (e.g., Intel) do not clear the
PMKID list even when wpa_supplicant explicitly sets the list to be
empty. In such a case, the driver ends up trying to use PMKSA caching
with the AP and wpa_supplicant may not have the PMK that would be needed
to complete 4-way handshake.
RSN processing already had some code for aborting PMKSA caching by
sending EAPOL-Start. However, this was not triggered in this particular
case where the driver generates the RSN IE. With this change, this case
is included, too, and the failed PMKSA caching attempt is cleanly
canceled and wpa_supplicant can fall back to full EAP authentication.
It looks like Qt does not support SVG format by default on Windows and
it was not trivial to add the plugin into the build, so for now, build a
16x16 PNG icon file for Windows binary to avoid showing an invisible
icon in the tray.
I fixed the engine issue in phase2 of EAP-TTLS. The problem was that you
only defined one engine variable, which was read already in phase1. I
defined some new variables:
engine2
engine2_id
pin2
and added support to read those in phase2 wheres all the engine
variables without number are only read in phase1. That solved it and I
am now able to use an engine also in EAP-TTLS phase2.
Find attached the patch that creates a new driver: roboswitch. This
driver adds support for wired authentication with a Broadcom
RoboSwitch chipset. For example it is now possible to do wired
authentication with a Linksys WRT54G router running OpenWRT.
LIMITATIONS
- At the moment the driver does not support the BCM5365 series (though
adding it requires just some register tweaks).
- The driver is also limited to Linux (this is a far more technical
restriction).
- In order to compile against a 2.4 series you need to edit
include/linux/mii.h and change all references to "u16" in "__u16". I
have submitted a patch upstream that will fix this in a future version
of the 2.4 kernel. [These modifications (and more) are now included in
the kernel source and can be found in versions 2.4.37-rc2 and up.]
USAGE
- Usage is similar to the wired driver. Choose the interfacename of
the vlan that contains your desired authentication port on the router.
This name must be formatted as <interface>.<vlan>, which is the
default on all systems I know.
Remove the old code from driver_wext.c since the private ioctl interface is
never going to be used with mac80211. driver_nl80211.c has an
implementation than can be used with mac80211 (with two external patches to
enable userspace MLME configuration are still required, though).
Updated OpenSSL code for EAP-FAST to use an updated version of the
session ticket overriding API that was included into the upstream
OpenSSL 0.9.9 tree on 2008-11-15 (no additional OpenSSL patch is
needed with that version anymore).
GCC 4.4 cleaned up some more C++ headers. You always have to #include
headers directly and cannot rely for things to be included indirectly.
> g++ -c -pipe -O2 -Wall -W -D_REENTRANT -DCONFIG_CTRL_IFACE
-DCONFIG_CTRL_IFACE_UNIX -DQT_NO_DEBUG -DQT_GUI_LIB -DQT_CORE_LIB -DQT_SHARED
-I/usr/share/qt4/mkspecs/linux-g++ -I. -I/usr/include/qt4/QtCore
-I/usr/include/qt4/QtCore -I/usr/include/qt4/QtGui -I/usr/include/qt4/QtGui
-I/usr/include/qt4 -I. -I.. -I../../src/utils -I../../src/common -I.moc -I.ui -o
.obj/wpagui.o wpagui.cpp
> wpagui.cpp: In constructor 'WpaGui::WpaGui(QWidget*, const char*,
Qt::WFlags)':
> wpagui.cpp:98: error: 'printf' was not declared in this scope
From: Martin Michlmayr <tbm@cyrius.com>
Bug: http://bugs.debian.org/505041
Signed-off-by: Kel Modderman <kel@otaku42.de>
delaying Michael MIC error reports by a random amount of time between 0 and
60 seconds if multiple Michael MIC failures are detected with the same PTK
(i.e., the Authenticator does not rekey PTK on first failure report). This
is disabled by default and can be enabled with a build option
CONFIG_DELAYED_MIC_ERROR_REPORT=y in .config.
This may help in making a chopchop attack take much longer time by forcing
the attacker to wait 60 seconds before knowing whether a modified frame
resulted in a MIC failure.
Added a new configuration option, wpa_ptk_rekey, that can be used to
enforce frequent PTK rekeying, e.g., to mitigate some attacks against TKIP
deficiencies. This can be set either by the Authenticator (to initiate
periodic 4-way handshake to rekey PTK) or by the Supplicant (to request
Authenticator to rekey PTK).
With both wpa_ptk_rekey and wpa_group_rekey (in hostapd) set to 600, TKIP
keys will not be used for more than 10 minutes which may make some attacks
against TKIP more difficult to implement.
This may be needed if the AP does not disconnect in case of EAP-FAST
unauthenticated provisioning (EAP-Failure). Adding the local short timeout
will speed up the process in such a case by reducing the wait (which can
often be up to 60 seconds).
This allows identity (etc.) variables to be removed from configuration
which is different from setting them to an empty string. For example,
EAP-SIM and EAP-AKA can now be configured to use identity string generation
from SIM/USIM by clearing the identity string in wpa_gui.
Setting the value of the SET_NETWORK command to NULL (without quotation)
unsets the variable, i.e., removes it from configuration file. This is
needed to allow GUI programs to clear variables, e.g., identity for
EAP-AKA/SIM.
Allow application to be started in the system tray only when started with
the `-t' command line argument.
Signed-off-by: Kel Modderman <kel@otaku42.de>
When the system tray icon is created, qApp's setQuitOnLastWindowClosed
property is set to false, therefore do _not_ ignore widget close events, or
else wpa_gui will refuse to exit when the window manager is logging out.
While at it, remove WpaGui::fileExit() and connect fileExitAction to
quit().
Signed-off-by: Kel Modderman <kel@otaku42.de>
A bug just got reported as a result of this for mac80211 drivers.
https://bugzilla.redhat.com/show_bug.cgi?id=459399
The basic problem is that since taking the device down clears the keys
from the driver on many mac80211-based cards, and since the mode gets
set _after_ the keys have been set in the driver, the keys get cleared
on a mode switch and the resulting association is wrong. The report is
about ad-hoc mode specifically, but this could happen when switching
from adhoc back to managed mode.
This function was getting way too long, so let's split it into WPA and
non-WPA cases as separate functions. In addition, remove the confusing
"Try to find non-WPA AP" debug message if a WPA-enabled AP is already
selected (as reported by Andriy Tkachuk).
but still show a one time tray message to indicate to the user that the
program is still running in the tray if they triggered the window manager
close button.
Signed-off-by: Kel Modderman <kel@otaku42.de>
Do not connect lastWindowClosed() to quit(), instead explicitly close the
application if File->Exit or window manager close button is activated.
This allows the tray app to avoid being closed with last visible window,
and launch scan and event history windows individually.
Signed-off-by: Kel Modderman <kel@otaku42.de>
Enhance the wpa_gui-qt4 icon:
* removed unused layer
* moved spurious rectangle back where it belongs
* removed flat edge from top of the lower white glow object
Signed-off-by: Bernard Gray <bernard.gray@gmail.com>
mlme.c: In function 'ieee80211_rx_mgmt_action':
mlme.c:1990: warning: implicit declaration of function
'ieee80211_rx_mgmt_ping_action'
...
mlme.o(.text+0x3007): In function `ieee80211_sta_rx':
/home/ant/hostap/hostap06/hostap/wpa_supplicant/mlme.c:1990: undefined reference
to `ieee80211_rx_mgmt_ping_action'
collect2: ld returned 1 exit status
When the initial scan is made, just the cached results from the driver
are used. If this is empty, it's useless to post the results since
another scan is being scheduled immediately. This just causes extra
processing from listeners for no gain.
The scan path to initiate another scan if the initial association failed
was broken due to wpa_s->scan_req being zeroed earlier in
wpa_supplicant_scan(). This caused the second scan to bail out early
since it thought this was not a requested scan.
Add system tray icon support to wpa_gui-qt4. The tray icon remains quiet
when the main dialog is visible, so it should not cause too much pain for
more conservative users of wpa_gui. The addition involves the following
changes:
* when closing wpa_gui via window manager close box, wpa_gui close event is
ignored and it is minimised to system tray. A status message is displayed
(or popup dialog box if tray messages are not supported) to provide a
visual hint that the program is still running in the background.
* add File->Exit slot handler to facilitate application quit from main
dialog
* provide a context menu with a short list of useful actions
* show/hide main dialog when icon is triggered (single click)
* ensure main dialog is visible when event handler or scan results is
chosen from tray icon context menu
* show tray messages on connected and disconnected events, display a status
message a few seconds after connected events
Signed-off-by: Kel Modderman <kel@otaku42.de>
When integrating the new art, this UI entry:
<pixmapfunction>qPixmapFromMimeSource</pixmapfunction>
Caused the following error:
.obj/wpagui.o: In function `Ui_WpaGui::setupUi(QMainWindow*)':
wpagui.cpp:(.text._ZN9Ui_WpaGui7setupUiEP11QMainWindow[Ui_WpaGui::setupUi(QMainWindow*)]+0xd3): undefined reference to `qPixmapFromMimeSource(QString const&)'
collect2: ld returned 1 exit status
Removing qPixmapFromMimeSource seems to have no unwanted side effects, and
allows successful build again. Research leads me to believe it depends on
Qt3Support, which we do not want.
Signed-off-by: Kel Modderman <kel@otaku42.de>
Introducing an original wpa_gui icon, in svg format, with Makefile for
easy conversion to other icon formats. The icon is thanks to Bernard Gray.
Signed-off-by: Bernard Gray <bernard.gray@gmail.com>
Signed-off-by: Kel Modderman <kel@otaku42.de>
IEEE 802.11w/D6.0 defines new AKMPs to indicate SHA256-based algorithms for
key derivation (and AES-CMAC for EAPOL-Key MIC). Add support for using new
AKMPs and clean up AKMP processing with helper functions in defs.h.
This updates management frame protection to use the assocition ping process
from the latest draft (D6.0) to protect against unauthenticated
authenticate or (re)associate frames dropping association.
This adds most of the new frame format and identifier definitions from IEEE
802.11w/D6.0. In addition, the RSN IE capability field values for MFP is
replaced with the new two-bit version with MFPC (capable) and MFPR
(required) processing.
This adds some parts needed to use usermode MLME with the current mac80211
(plus a patch to add a new cfg80211 command; not yet submitted to
wireless-testing). This version creates a monitor interface for management
frames and is able to send Probe Request frames during scan. However, it
looks like management frame reception is not yet working properly. In
addition, mlme_{add,remove}_sta() handlers are still missing.
wpa_sm_set_config() can be called even if the network block does not
change. However, the previous version ended up calling
pmksa_cache_notify_reconfig() every time and this cleared the network
context from PMKSA cache entries. This prevented OKC from ever being used.
Do not call pmksa_cache_notify_reconfig() if the network context remains
unchanged to allow OKC to be used.
When scan results got moved from wpa_scan_result -> wpa_scan_res, the
'maxrate' member was dropped from wpa_scan_res. The D-Bus interface
used 'maxrate', which was replaced with wpa_scan_get_max_rate().
Unfortunately, wpa_scan_get_max_rate() returns 802.11 rate values
directly from the IE, where 'maxrate' was the rate in bits/second. The
supplicant internally fakes an IE for wpa_scan_res from the value of
wpa_scan_result->maxrate, but interprets ->maxrate as an 802.11 rate
index.
As a side-effect, this fixes a soft-break of the D-Bus control API since
the wpa_scan_res change was introduced.
Function 'wpa_sm_set_config' used the argument 'config' as the network
context which is a pointer to a local variable of the function
'wpa_supplicant_rsn_supp_set_config'.
This is one reason why no proactive key was generated. This network
context never matched with the network context saved in the pmksa cache
entries.
The structure 'rsn_supp_config' has already a member 'network_ctx' which
is now filled in by this patch with 'ssid'.
Signed-off-by: Michael Bernhard <michael.bernhard@bfh.ch>
Documentation appeared a little vague about which options are global and
which are tied to a particular interface. This leads to confusion when
using certain combinations of options, e.g. the command "wpa_supplicant
-c /etc/wpa_supplican.conf -u" will not do what is intuitively expected
from it - it will not read the config file given with -c option because
no -i option was given. This command is still valid because -u option is
used. The wpa_supplicant running like this will also not listen on any
control socket, because the socket file name is usually given in the
config file. This command line also happens to be the default in Fedora 9.
This patch does not try to change any behaviour, but rather document
these nuances clearly.
This avoids getting stuck in state where wpa_supplicant has canceled scans,
but the driver is actually in disassociated state. The previously used code
that controlled scan timeout from WPA module is not really needed anymore
(and has not been needed for past four years since authentication timeout
was separated from scan request timeout), so this can simply be removed to
resolved the race condition. As an extra bonus, this simplifies the
interface to WPA module.
[Bug 261]
driver_nl80211.c is based on driver_wext.c and it is still using Linux
wireless extensions for many functions. Over time, the new driver interface
code should be modified to use nl80211/cfg80211 for everything.
This was not accurate since this was mostly based on total runtime of an
eapol_test run. The real improvement in the bignum routines is much larger
(mayby twice as fast as before).
CONFIG_INTERNAL_LIBTOMMATH_FAST=y in .config can now be used to enable all
optimized routines at a cost of about 4 kB. This is small enough increase
in size to justify simplified configuration.
At the cost of about 1 kB of additional binary size, the internal
LibTomMath can be configured to include faster div routine to speed up DH
and RSA. This can be enabled with CONFIG_INTERNAL_LIBTOMMATH_FAST_DIV=y in
.config.
At the cost of about 0.5 kB of additional binary size, the internal
LibTomMath can be configured to include faster sqr routine to speed up DH
and RSA. This can be enabled with CONFIG_INTERNAL_LIBTOMMATH_FAST_SQR=y in
.config.
Depending on how the driver implements IBSS searching and creation, it
may need to perform one or more scans before successfully completing the
association operation. Therefore, increase the timeout for IBSS
association operations so that the supplicant doesn't interrupt the
driver as much.
Add a cost of about 2.5 kB of additional cost, the internal LibTomMath can
be configured to include fast exptmod routine to speed up DH and RSA.
This can be enabled with CONFIG_INTERNAL_LIBTOMMATH_FAST_EXPTMOD=y in
.config.
In situations where the driver does background scanning and sends a
steady stream of scan results, wpa_supplicant would continually
reschedule the scan. This resulted in specific SSID scans never
happening for a hidden AP, and the supplicant never connecting to the AP
because it never got found. Instead, if there's an already scheduled
scan, and a request comes in to reschedule it, and there are enabled
scan_ssid=1 network blocks, let the scan happen anyway so the hidden
SSID has a chance to be found.
The internal TLS implementation can now use both PKCS #1 RSA private key
and PKCS #8 encapsulated RSA private key. PKCS #8 encrypted private key is
not yet supported.
The TLS client changes in ssl3_get_server_hello() were based on the
pre-RFC 5077 version of OpenSSL and they hardcoded s->hit to 1 in case
PAC-Opaque was used. This prevented fallback to full TLS handshake in case
the server rejected PAC-Opaque in ClientHello. The fixed version simplifies
ssl3_get_server_hello() and uses the new RFC 5077 functionality in OpenSSL
(ssl3_check_finished) to allow the state machine handle start of
abbreviated handshake based on the used ticket.
crypto_binding=# in phase1 network parameter can now be used to change the
PEAPv0 cryptobinding behavior (0 = do not use, 1 = optional (default),
2 = required).
Explain that wpa_supplicant supports a variety of drivers, but only a
subset of them are chosen at compile time.
Signed-off-by: Kel Modderman <kel@otaku42.de>
Allow the user to set the IP address of the eapol_test client. This if
very useful when you have a machine with many interfaces and want to use a
particular one for testing RADIUS connectivity. For instance when I run the
national eduroam proxy I can only connect to other server from a particular
address, an our machine happens to have several IPs. So if I want to run
connectivity tests, I must make sure that my test uses a particular
interface. The -A option allows one to set this).
(jm: cleaned up to use radius configuration structure instead of global
variable for the address and added IPv6 support)
Implements the Chargable-User-Identity (CUI), as defined in RFC 4372.
Option "-i" causes the eapol_test to send a NUL CUI - which is a request to
send a CUI back. Capital "-I" allows to specify the value of the CUI.
This has been defined for cases where the client wants to reauthenticate.
It looks like Microsoft implementation does not match with their
specification as far as PRF+ label usage is concerned.. IPMK|CMK is derived
without null termination on the label, but the label for CSK derivation
must be null terminated.
This allows cryptobinding to be used with PEAPv0 in a way that
interoperates with Windows XP SP3 (RC2) and as such, this functionality is
now enabled as an optional addition to PEAPv0.
EAP-PEAP was the only method that used the external eap_tlv.c peer
implementation. This worked fine just for the simple protected result
notification, but extending the TLV support for cryptobinding etc. is not
trivial with such separation. With the TLV processing integrated into
eap_peap.c, all the needed information is now available for using
additional TLVs.
This adds support for PS3 wireless to wpa_supplicant.
Although PS3 wireless driver is designed to conform the WEXT standard
as much as possible, unfortunately the wext driver wrapper of
wpa_supplicant can not support PS3 wireless fully because:
- PS3 wireless driver uses private WEXT ioctls for accepting PSK of
WPA-Personal from the userland.
WEXT does not specify the way to do it.
- The association and 4-way handshake are done by PS3 virtual
wireless device. The guest OSes can not interfere it.
- No EAPOL frames are allowed to go outside of the
hypervisor/firmware nor come from. They are eaten by the firmware.
Thus I needed to make a new driver wrapper for PS3 wireless.
This patch can be applied against the latest 0.6.x tree.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
The old version was using struct wpa_sm::bssid which is not necessarily
updated to point to the correct target address when doing over-the-air FT
since the address is used before the association has actually been
completed.
When a WpaMsg item to the QValueList WpaMsgList, there's no constructor
that the QValueList can call. This is a port of the fix from the stable
branch where it builds fine.
Number of TLVs were processed in groups and these cases were now separated
into more flexible processing of one TLV at the time. wpabuf_concat()
function was added to make it easier to concatenate TLVs. EAP Sequences are
now supported in both server and peer code, but the server side is not
enabled by default.
The Debian package checker "lintian" was making noise about
wpa_supplicant.conf(5). It was caused by a line beginning with ', which is
apparently not liked by man(1).
I suggest the use of <emphasis>word</emphasis> where 'word' is used at the
moment.
Signed-off-by: Kel Modderman <kel@otaku42.de>
