This adds a string "FILS_HLP_SENT" to connect event when HLP is sent
as part of ASSOC/CONNECT request.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit defines an attribute
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY to signify the preferred
channel list policy for external ACS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add new vendor commands for starting and stoppping spectral scan. Add
vendor attributes for configuring spectral scan parameters as part of
the start command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add attribute for TA max duration after last TA received. So that local
time is synchromous to other communicating OCB STAs. If the duration
expires, OCB STA without UTC time source is not in sync to other STAs
and stop scheduling DSRC channel switch after max duration.
Signed-off-by: Zhaoyang Liu <zhaoyang@codeaurora.org>
Signed-off-by: Ferry Zhou <tianguiz@codeaurora.org>
Document QCA vendor OCB commands about IEEE Std 802.11 communication
outside the context of a basic service set. Also define all attributes
for the specific OCB commands.
Signed-off-by: Zhaoyang Liu <zhaoyang@codeaurora.org>
Signed-off-by: Ferry Zhou <tianguiz@codeaurora.org>
Do not accept a link-local IPv4 address when waiting for a valid DHCP
address. This helps with hs20-osu-client use cases where DHCP response
has not yet been received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
1. Add new attribute to report corresponding antenna information to the
chain RSSI which is used in subcmd
QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI.
2. Add a series of attr to support the new wmi interface
WMI_PDEV_PARAM_ANT_DIV_USRCFG which export parameters setting of antenna
diversity algorithm to userspace.
Signed-off-by: Li Feng <lifeng@qti.qualcomm.com>
QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_ABS_DELAY is added to set
propagation delay's absolute value. This is a more detailed version of
QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY.
Signed-off-by: Zhang Qian <zhangq@qti.qualcomm.com>
draft-harkins-owe-07.txt does not specify these parameters, so need to
pick something sensible to use for the experimental implementation. The
Suite B 128-bit level AKM 00-0F-AC:11 has reasonable parameters for the
DH group 19 case (i.e., SHA256 hash), so use it for now. This can be
updated if the OWE RFC becomes clearer on the appropriate parameters
(KEK/KCK/MIC length, PRF/KDF algorithm, and key-wrap algorithm).
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds AP side processing for OWE Diffie-Hellman Parameter element in
(Re)Association Request frame and adding it in (Re)Association Response
frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a helper function that parses candidate list from command line
arguments.
This function will be used (in the following commits) to add
a candidate list to BSS transition management query.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This extends the GAS/ANQP parser in wpa_supplicant to process MBO
ANQP-elements and indicate received Cellular Data Connection Preference
values over the control interface.
When a valid MBO ANQP-element is received, the following control
interface message is sent:
RX-MBO-ANQP <BSSID> cell_conn_pref=<value>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
MBO techspec v0.0_r27 changed the MBO ANQP-element format. The MBO
element in ANQP query should now include an MBO Query List element that
contains a list of MBO elements to query.
Add API to add the MBO Query List to an ANQP query.
Format:
ANQP_GET <addr> <info_id>[,<info_id>]...[,mbo:<subtype>...]
Example for querying neighbor report with MBO cellular data
connection preference:
ANQP_GET <bssid> 272,mbo:2
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
As FCC DFS requirement does not explicitly mention about the validity of
the (pre-)CAC when channel is switched, it is safe to assume that the
pre-CAC result will not be valid once the CAC completed channel is
switched or radar detection is not active on the (CAC completed) channel
within a time period which is allowed (10 seconds - channel switch time)
as per FCC DFS requirement.
Use the new driver event to allow the driver to notify expiry of the CAC
result on a channel. Move the DFS state of the channel to 'usable' when
processing pre-CAC expired event. This means any future operation on
that channel will require a new CAC to be completed. This event is
applicable only when DFS is not offloaded to the kernel driver.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Add QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT for setting the number
of antennas that will be active in different modes for each connection.
Signed-off-by: Alexei Avshalom Lazar <qca_ailizaro@qca.qualcomm.com>
Define a new attribute QCA_WLAN_VENDOR_ATTR_CONFIG_SUB20_CHAN_WIDTH.
This attribute can set a station device to work in 5 or 10 MHz channel
width while in disconnect state.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The __FAVOR_BSD macro was previously used in netinet/udp.h to select
between two different names of the variables in struct udphdr. Define
that to force the versions with the uh_ prefix. In addition, use the
same style consistently within fils_hlp.c.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add IEEE 802.11ax definitions for config, IEEE structures, and
constants. These are still subject to change in the IEEE process.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
sha384_prf() is used both with Suite B and FILS, so add CONFIG_FILS as
another alternative to building in this functionality.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, any potential (even if very unlikely) local operation error
was ignored. Now these will result in aborting the negotiation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use the defines for vht_oper_chwidth values more consistently in
hostapd_set_freq_params() to make this more readable.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit introduces the vendor command to set the trace level
for the respective QCA host driver module.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new FILS-HLP-RX control interface event is now used to report
received FILS HLP responses from (Re)Association Response frame as a
response to the HLP requests configured with FILS_HLP_REQ_ADD.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These can be reused for other purposes than just the DHCP snoofing for
Proxy ARP. In addition, use more complete definition of the parameters
based on the current IANA registry.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Introduce definitions for QCA vendor specific subcommands and attributes
for fetching BSS transition status.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces QCA vendor commands and the corresponding
attributes to set/get NUD (Network Unreachability Detection) statistics.
The set NUD statistics configures the requisite parameters to the host
driver and thereby triggers the start/stop of collection of statistics.
The get stats fetches the statistics collected in the host driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This functionality can be used outside wpa_set_disable_ht40(), so move
the generic part to a helper function.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This gets rid of an unnecessary duplication of the definitions since all
the code has now been moved to using the earlier RSN_CIPHER_SUITE_*
definitions.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds the cipher suite selector values for ciphers that are not
really used with RSN, but are needed to be able to replace
WLAN_CIPHER_SUITE_* definitions with RSN_CIPHER_SUITE_*.
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of an unnecessary duplication of the definitions since all
the code has now been moved to using the earlier RSN_AUTH_KEY_MGMT_*
definitions.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE 802.11 standard defines the suite selectors in <OUI>:<subtype>
format where OUI uses hexadecimal format and subtype decimal format.
These WLAN_AKM_SUITE_* definitions ended up getting written incorrectly
by interpretting the decimal part as hexadecimal and as such, by having
an incorrect value. However, the older RSN_AUTH_KEY_MGMT_* values were
defined with correct values and those definitions were used in most
locations.
This commit fixes the AKM suite selector values in RADIUS WLAN-AKM-Suite
attribute for FILS and Suite B. In addition, the AKM values used in
nl80211 driver configuration (NL80211_ATTR_AKM_SUITES) are fixed for the
Suite B cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit defines a QCA vendor command
QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE that carries required
information leading to the power save failure. This will be an event
from the host driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces the QCA vendor command and the attributes which
facilitate the host driver to use an external user space entity for
performing automatic channel selection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds helper functions for deriving PMK and PMKID from ERP exchange
in FILS shared key authentication as defined in IEEE Std 802.11ai-2016,
12.12.2.5.2 (PMKSA key derivation with FILS authentication). These
functions is used to fix PMK and PMKID derivation which were previously
using the rMSK directly as PMK instead of following the FILS protocol to
derive PMK with HMAC from nonces and rMSK.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These elements can be used for pre-standard publication testing of HE
before P802.11ax draft assigns the element ID extension. The payload of
these vendor specific elements is defined by the latest P802.11ax draft.
Please note that the draft is still work in progress and the element
payload is subject to change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a call to the notify_beacon_loss() callback functions when
beacon loss is detected. In addition, a new CTRL-EVENT-BEACON-LOSS event
is made available through the wpa_supplicant control interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd control interface event "BEACON-RESP-RX <STA address>
<dialog token> <report mode> <beacon report>" is now used to report
received beacon reports as a reponse to the REQ_BEACON operation.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new BEACON-REQ-TX-STATUS control interface event is now used to
report whether a beacon request (from REQ_BEACON command) was delivered
successfully. This event has the following parameters: <STA address>
<dialog token> <ack=0/1>.
Signed-off-by: Jouni Malinen <j@w1.fi>
