While adding support for IGTK and BIGTK here, I tested this without
protections (i.e., with protections removed from both wpa_supplicant and
the driver), and while I got some bad resets on the debugfs values, it
should have failed with "unexpected connectivity".
Fix this to be correct - we need to reset the GTK PN, not the PTK PN in
this test.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replace the gtk boolean by a keytype value indicating
GTK or PTK, to be able to extend to other types later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes it more convenient to run tests with builds that disable
TKIP/WPA(v1) support completely.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When going through 4-way handshake, the station side reports
CTRL-EVENT-CONNECTED after having sent out EAPOL-Key msg 4/4. The AP
side reports AP-STA-CONNECT after having completed processing of this
frame. Especially when using UML with time travel, it is possible for
the connectivity test to be started before the AP side has configured
the pairwise TK if the test is triggered based on CTRL-EVENT-CONNECTED
instead of AP-STA-CONNECT.
Add explicit wait for AP-STA-CONNECT in some of these cases to reduce
likelihood of reporting failures for test cases that are actually
behaving as expected. This shows up with "dev1->dev2 unicast data
delivery failed" in the test log.
Do the same before requesting reauthentication from the station side
since that has a similar issue with the EAPOL-Start frame getting
encrypted before the AP is ready for it.
Signed-off-by: Jouni Malinen <j@w1.fi>
hostapd implementation was changed to use a valid Status Code when
rejecting the connection. This test case was forgotten at the time, but
it needs a matching change to allow the new value (1 instead of 14).
Signed-off-by: Jouni Malinen <j@w1.fi>
These test cases do not really verify any specific DUT behavior
automatically, i.e., these are here to generate sniffer captures for
manual analysis.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
After successfully passing the 525 tests on a remote setup mark the
tests as remote compatible.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
The generic cmd_execute() function was introduced in a manner that
converted the argument array to a string and used shell to run the
command unconditionally. This is not really desirable, so move back to
using the command array by default and use the single command string
with a shell only when really needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
The ap_ciphers tests used to do file operations locally in python. Start
using the cmd_execute() general function for file operations so that
this would also work on remote setups.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
Use a monitor interface given in the command line that is not also a
station or an AP as a monitor running wlantest on the channel used by
the test. This makes all the tests that use wlantest available for
execution on real hardware on remote hosts.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (4) converts the cases that call hostapd.add_ap() from a
helper function that got apdev[i] as an argument.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (1) converts the cases where apdev[#]['ifname'] was used as
the argument to hostapd.add_ap().
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Write the main interface address to the tkip_mic_test debugfs file
to generate Michael MIC failure event (which is different than the
p2p_dev_addr when a dedicated P2P Device interface is used).
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This extends testing coverage of PMF group management cipher suites to
include all the cases supported by the driver (existing BIP =
AES-128-CMAC and the new BIP-GMAC-128, BIP-GMAC-256, BIP-CMAC-256).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of returning "skip" from the test function, raise the new
HwsimSkip exception to indicate a test case was skipped.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since run-tests.py is now required to run as root, there is no need to
use the somewhat awkward "sudo tee" construction; instead, just write
directly to the file.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to replace data connectivity testing to use
something else than local hwsim_test binary on the controller device.
Signed-off-by: Jouni Malinen <j@w1.fi>
ap_cipher_tkip_countermeasures_{ap,sta} printed out the MAC addresses in
stdout which resulted in the debug log not starting the PASS/FAIL
information at the beginning of the line. Hide these unnecessary prints
to avoid that.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The return value was lost and GCMP, CCMP-256, and GCMP-256 test cases
were reporting PASS instead of SKIP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Only run-tests.py is actually executed, so there is no need to specify
the interpreter in all the helper files and test script files.
Signed-off-by: Jouni Malinen <j@w1.fi>
Now that wpa_supplicant requests the driver (cfg80211) to clear its scan
cache automatically after each BSS_FLUSH/FLUSH command, the previously
used ignore_old_scan_res workaround should not be needed for the hwsim
test cases anymore.
Signed-hostap: Jouni Malinen <j@w1.fi>
