This needs to be callable through the EAPOL supplicant wrappers to allow
FILS implementation to use ERP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This implements Key-Auth derivation for (Re)Association Request frames
(see P802.11ai/D11.0 12.12.2.6.2) and (Re)Association Response frames
(see P802.11ai/D11.0 12.12.2.6.3).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is the PTKSA key derivation used as part of the FILS authentication
exchange. See P802.11ai/D11.0 12.12.2.5.3.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it cleaner for the FILS implementation to use the same design
for setting Authentication frame elements as was already done with SAE.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add operations to allow low level control over RF sectors in QCA DMG
(11ad) chipsets. Operations include getting/setting the configuration of
a specific sector, as well as getting/setting the selected sector which
the HW uses to communicate with a specific station.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
That function does not need the full EAP header -- it only needs to know
which EAP identifier to use in the message. Make this usable for cases
where the previous EAP message may not exist (FILS).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This changes 4-way handshake authenticator processing to decrypt the
EAPOL-Key frames using an AEAD cipher (AES-SIV with FILS AKMs) before
processing the Key Data field. This replaces Key MIC validation for the
cases where AEAD cipher is used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This changes 4-way handshake authenticator processing to decrypt the
EAPOL-Key frames using an AEAD cipher (AES-SIV with FILS AKMs) before
processing the Key Data field. This replaces Key MIC validation for the
cases where AEAD cipher is used. This needs to move the EAPOL-Key msg
2/4 RSN element processing to happen only after the PTK has been derived
and validated. That is done for all AKMs to avoid extra complexity with
having to maintain two code paths for this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This modifies wpa_eapol_key_send() to use AEAD cipher (AES-SIV for FILS
AKMs) to provide both integrity protection for the EAPOL-Key frame and
encryption for the Key Data field. It should be noted that this starts
encrypting the Key Data field in EAPOL-Key message 2/4 while it remains
unencrypted (but integrity protected) in non-FILS cases. Similarly, the
empty Key Data field in EAPOL-Key message 4/4 gets encrypted for AEAD
cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This will be needed to be able to implement AEAD cipher support from
FILS that will need to use KEK to protect the frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Suite B 192-bit addition from IEEE Std 802.11ac-2013 replaced the
previous fixed length Key MIC field with a variable length field. That
change was addressed with an addition of a new struct defined for the
second MIC length. This is not really scalable and with FILS coming up
with a zero-length MIC case for AEAD, a more thorough change to support
variable length MIC is needed.
Remove the Key MIC and Key Data Length fields from the struct
wpa_eapol_key and find their location based on the MIC length
information (which is determined by the AKMP). This change allows the
separate struct wpa_eapol_key_192 to be removed since struct
wpa_eapol_key will now include only the fixed length fields that are
shared with all EAPOL-Key cases in IEEE Std 802.11.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Calculate the hashed realm from hostapd erp_domain configuration
parameter and add this to the FILS Indication element when ERP is
enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If FILS is enabled, indicate that in Beacon, Probe Response, and
(Re)Association Response frames in the Extended Capabilities element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds CONFIG_FILS=y build configuration option and new key
management options for FILS authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds definitions for new information elements from P802.11ai/D11.0
and parsing of these IEs.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The previous implementation was hardcoded to use 128-bit AES key
(AEAD_AES_SIV_CMAC_256). Extend this by allowing AEAD_AES_SIV_CMAC_384
and AEAD_AES_SIV_CMAC_512 with 192-bit and 256-bit AES keys.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the CRC-32 routine to be shared for other purposes in
addition to the WEP/TKIP/FCS within wlantest.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Station should be able to connect initially without ft_pmk_cache filled,
so the target AP has the PSK available and thus the same information as
the origin AP. Therefore neither caching nor communication between the
APs with respect to PMK-R0 or PMK-R1 or VLANs is required if the target
AP derives the required PMKs locally.
This patch introduces the generation of the required PMKs locally for
FT-PSK. Additionally, PMK-R0 is not stored (and thus pushed) for FT-PSK.
So for FT-PSK networks, no configuration of inter-AP communication is
needed anymore when using ft_psk_generate_local=1 configuration. The
default behavior (ft_psk_generate_local=0) remains to use the pull/push
protocol.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This also implements the macsec_get_capability for the macsec_qca
driver to maintain the existing behavior.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
RFC 5931 Section 2.8.5.1 does not list the Prep field as something that
the server validates to match the Request. However, the supplicant side
has to use the same pre-processing mechanism for the password for the
authentication to work, so we may as well as enforce this field to match
the requested value now that wpa_supplicant implementation is fixed to
copy the value from the request.
Signed-off-by: Jouni Malinen <j@w1.fi>
Fix the pre-processing field in the response when EAP_PWD_PREP_MS is
being used. This fixes interoperability with EAP-pwd servers that
validate the Prep field in EAP-pwd-ID/Response when the RFC2759
(PasswordHashHash) pre-processing is used.
Signed-off-by: Brian Candler <B.Candler@pobox.com>
Clean up the driver interface by passing pointers to struct receive_sc
down the stack to the {create,delete}_recevie_sc() ops, instead of
passing the individual properties of the SC.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Clean up the driver interface by passing pointers to struct transmit_sc
down the stack to the {create,delete}_transmit_sc() ops, instead of
passing the individual arguments.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This basically just follows commit
587b0457e0 ('LibreSSL: Fix build with
LibreSSL') with the same pattern, which was missed here.
Signed-off-by: Julian Ospald <hasufell@hasufell.de>
Due to a missing guard for old OpenSSL code, SSL_library_init() was not
called, which is required for LibreSSL. Likewise for cleanup.
Signed-off-by: Christian Neukirchen <chneukirchen@gmail.com>
Add LibreSSL check to old OpenSSL #ifdef guard as DH_{get0,set0}_key()
is not implemented in LibreSSL.
Signed-off-by: Christian Neukirchen <chneukirchen@gmail.com>
Add attributes for specifing the frequency where FTM/AOA measurement is
done over the air. This allows the user space framework to maintain its
own cache of peers without depending on the kernel scan results cache,
or perform scans less often (since entries in the kernel scan results
cache expire quickly). The change is backward compatible. If the
frequency attribute is not specified, the kernel scan results cache will
be queried, like done today.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Clean up the driver interface by passing pointers to struct receive_sa
down the stack to the {create,enable,disable}_receive_sa() ops, instead
of passing the individual properties of the SA.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Clean up the driver interface by passing pointers to struct transmit_sa
down the stack to the {create,enable,disable}_transmit_sa ops, instead
of passing the individual properties of the SA.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Clean up the driver interface by passing pointers to structs transmit_sa
and receive_sa down the stack to get_receive_lowest_pn(),
get_transmit_next_pn(), and set_transmit_next_pn() ops, instead of
passing the individual arguments.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
These structs will be passed down to macsec drivers in a coming patch to
make the driver interface cleaner, so they need to be shared between the
core MKA implementation and the drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This makes it easier to copy a subset of definitions without
accidentally getting mismatching values.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends ANQP_GET command to support querying MBO cellular
preference also. The cellular preference can be requested along with
neigbor report by appending mbo:1 to the command arguments.
For example:
ANQP_GET <bssid> 272,mbo:1
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The user space app use QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI cmd to
get the corresponding antenna rssi value for the specific chain. And the
associcated attributes are added to configure the antenna diversity and
related selftest.
Signed-off-by: Li Feng <lifeng@qti.qualcomm.com>
The reason detail field was removed from non_pref_chan attr in MBO
v0.0_r25 draft. Don't parse for this element to be compliant with the
latest drafr.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
MBO capable APs can set association disallowed in the Beacon/Probe
Response frames. For testing purposes, the STA needs to be configured to
not ignore the association disallowed set by APs and continue to connect
to such AP like non-MBO enabled STA. Add a QCA vendor attribute for
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION vendor sub command to
configure the driver to ignore association disallowed functionality.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to find bss->drv separately for each parameter, so do
this once at the beginning of the function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add driver parameter command to force capability flag
WPA_DRIVER_FLAGS_BSS_SELECTION even if driver states otherwise. This is
mainly for testing purposes.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Ignore group members for which there is no supported channels
information when calculating common group frequencies.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This command carries 802.11 header and payload along with key (TK) and
PN for encryption/decryption purpose. Firmware/driver encrypts/decrypts
the given data and sends to userspace as a response to the command. User
space component can validate the data received from the driver to unit
test the hardware's encryption engine.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A weakness in the initial client taxonomy mechanism is from storing both
the Probe and Associate in struct sta_info. struct sta_info is created
after a client associates (or starts authentication frame exchange),
which means that any Probe Request frames sent prior to association are
not retained. The Associate Request frame has to be seen, and then
another Probe Request frame after association, before we have a
signature for the client.
Most clients send lots of Probe Request frames (lots and lots and lots
of Probes, actually), but a few do not. ChromeOS is notably sparing in
sending Probe Request frames, it can take a long time before a signature
for a ChromeOS device is available.
Store the most recent Probe Request frame in struct hostapd_sta_info
tracking list. When a struct sta_info is created, move the Probe Request
frame information from struct hostapd_sta_info to struct sta_info.
Signed-off-by: dgentry@google.com (Denton Gentry)
Signed-off-by: denny@geekhold.com (Denton Gentry)
Signed-off-by: rofrankel@google.com (Richard Frankel)
Signed-off-by: richard@frankel.tv (Richard Frankel)
Implement the signature mechanism described in the paper
"Passive Taxonomy of Wifi Clients using MLME Frame Contents"
published by Denton Gentry and Avery Pennarun.
http://research.google.com/pubs/pub45429.htmlhttps://arxiv.org/abs/1608.01725
This involves:
1. Add a CONFIG_TAXONOMY compile option. Enabling taxonomy incurs
a memory overhead of up to several kilobytes per associated
station.
2. If enabled, store the Probe Request and (Re)Associate Request frame in
struct sta_info.
3. Implement code to extract the ID of each Information Element,
plus selected fields and bitmasks from certain IEs, into a
descriptive text string. This is done in a new source file,
src/ap/taxonomy.c.
4. Implement a "signature qq:rr:ss:tt:uu:vv" command
in hostapd_cli to retrieve the signature.
Signatures take the form of a text string. For example, a signature
for the Nexus 5X is:
wifi4|probe:0,1,127,45,191,htcap:01ef,htagg:03,htmcs:0000ffff,vhtcap:338061b2,
vhtrxmcs:030cfffa,vhttxmcs:030cfffa,extcap:00000a0201000040|assoc:0,1,48,45,
221(0050f2,2),191,127,htcap:01ef,htagg:03,htmcs:0000ffff,vhtcap:339071b2,
vhtrxmcs:030cfffa,vhttxmcs:030cfffa,extcap:0000000000000040
Signed-off-by: dgentry@google.com (Denton Gentry)
Signed-off-by: denny@geekhold.com (Denton Gentry)
Signed-off-by: rofrankel@google.com (Richard Frankel)
Signed-off-by: richard@frankel.tv (Richard Frankel)
Previously, struct hostapd_iface sta_seen list head was initialized only
when completing interface setup. This left a window for operation that
could potentially iterate through the list before the list head has been
initialized. While the existing code checked iface->num_sta_seen to
avoid this case, it is much cleaner to initialize the list when struct
hostapd_iface is allocated to avoid any accidental missing of the extra
checks before list iteration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not generate an unused and invalid Request Authenticator (random
value) when constructing Accounting-Request packets. The correct Request
Authenticator is calculated subsequently in radius_msg_finish_acct()
using MD5(msg + shared secret).
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
This reverts commit 647862eb60.
The second check of device_ap_sme looks like duplicated, but it isn't
actually. The trick is nl80211_create_monitor_interface may change that
variable value and the second evaluation may give a different result.
This definitely isn't a very clear code, but that change caused a
regression for drivers that:
1) Don't report NL80211_ATTR_DEVICE_AP_SME
2) Don't support monitor mode
3) Don't support subscribing for PROBE_REQ and/or ACTION frames
like brcmfmac. With such drivers hostapd doesn't start anymore.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The places using drv->use_monitor were already skipping creation of the
monitor interface if drv->device_ap_sme == 0. This means that the
monitor interface operations would not have worked anyway and it is safe
to set drv->use_monitor to zero for all such cases. This fixes an issue
with management frame subscription not happening properly for the case
where the AP SME is in the driver and the driver supports monitor
interfaces (for other purposes).
This commit also removes the check for monitor support and the
previously used workaround that cleared drv->use_monitor in
drv->device_ap_sme == 1 case if monitor interface was not supported
since that condition cannot occur anymore.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Upon receiving FST Setup Request from some peer on some interface,
search is made to see if same peer is connected on other interface with
specific band_id. With multiple peers, bug in
fst_group_does_iface_appear_in_other_mbies() caused wrong peer address
to be returned sometimes.
Fix this with a modified, simplified search algorithm of peer's "other"
connection.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Fix some mistakes in the previous commit for adding QCA vendor commands
for indoor location.
Note: The renamed enum value does not change the ABI, but the addition
of QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INVALID in the beginning of enum
qca_wlan_vendor_attr_ftm_meas does renumber
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_* values. The previous values were
committed yesterday and have not been used in any released code yet, so
this is a justifiable quick fix.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Assign QCA vendor specific commands, attributes, and events for
supporting indoor location features.
These features include:
1. Fine timing measurement (FTM) - allows measurement of distance
between two stations. Based on IEEE P802.11-REVmc/D7.0, 11.24.6 FTM is
performed between two stations: one is an initiator, typically a client
that wants to measure distance to another AP, and one is a responder,
typically an AP which responds to measurement requests from other
clients. The responder can be configured to report its location, either
in absolute coordinates (LCI) or free-form description (LCR).
2. Angle of arrival (AOA) - allows measurement of azimuth and elevation
between two stations.
The above features can be combined to allow a station to get an accurate
indoor location.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Add configuration options that control publishing of fine timing
measurement (FTM) responder and initiator functionality via bits 70, 71
of Extended Capabilities element. Typically, FTM functionality is
controlled by a location framework outside hostapd. When framework is
activated, it will use hostapd to configure the AP to publish the FTM
functionality. See IEEE P802.11-REVmc/D7.0, 9.4.2.27.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Some deployed stations incorrectly consider nsts capability in
(Re)Association Response frame as required capability instead of maximum
capability and if it is greater than station's capability then beamform
will not happen in uplink traffic.
This commit adds support for an optional workaround to use station's
nsts capability in (Re)Association Response frame if the station's nsts
is less than AP by using the use_sta_nsts=1 configuration parameter.
This configuration is introduced in this commit and it is disabled by
default.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Some user space monitor wants to offload link layer statistics to
firmware. A new command QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT and
associcated attributes are added. The monitor will use this new command
to configure monitoring paramters and get link layer statistics.
Attributes added in this change:
1. Parameters for FW to trigger the statistics report
2. Peer STA power state
3. TX failure statistics
Signed-off-by: Zhang Qian <zhangq@qti.qualcomm.com>
Assign cs in ieee802_1x_mka_decode_dist_sak_body and reuse it.
Cleanup of key allocation: ieee802_1x_kay_generate_new_sak() and
ieee802_1x_mka_decode_dist_sak_body() both allocate a struct key_conf,
fill it, and ask ieee802_1x_kay_init_data_key() to allocate and set up a
struct data_key. They also allocate multiple key buffers and copy the
same data around. Stop moving data from buffer to buffer, and just
allocate what we really need.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Instead of copying from kay to a temporary struct, and then from the
struct to the sm, just copy from kay to cp.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This avoids unnecessary typecasting while still being able to compare
the value to CS_TABLE_SIZE without compiler warnings.
Signed-off-by: Jouni Malinen <j@w1.fi>
Share mka deletion implementation in ieee802_1x_participant_timer() for
the cak_life and mka_life expiration cases.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This takes care of priority comparison followed by MAC address
comparison if the priorities are identical.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This is a known constant value (CS_ID_LEN, i.e., the length of the EUI64
identifier) and does not need to be provided separately in these
function calls.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
to_use_sak is a Boolean variable, so there is no need for an if
statement to figure out whether to return TRUE or FALSE.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Use for loop to remove unnecessary goto use and similar cleanup to
simplify the loops in ieee802_1x_mka_i_in_peerlist(),
ieee802_1x_mka_decode_live_peer_body(), and
ieee802_1x_kay_decode_mkpdu().
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Each loop iteration resets body_peer in the beginning, so there is no
need to increment this pointer in the end.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
