The driver wrappers can now inform wpa_supplicant how many SSIDs can
be used in a single scan request (i.e., send multiple Probe Requests
per channel). This value is not yet used, but it can eventually be used
to allow a new scan command to specify multiple SSIDs to speed up
scan_ssid=1 operations. In addition, a warning could be printed if
scan_ssid=1 is used with a driver that does not support it
(max_scan_ssids=0).
If wpa_supplicant is started with -u but the DBus service is already
registered wpa_supplicant will bail out. However, it will segfault
in wpa_supplicant_deinit because global->drv_priv wasn't allocated
yet.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
RSN IBSS uses authentication per-STA and that is initialized separately,
so there is no need to enable the per-BSS like authentication that is
used with APs.
This commit adds a new build option, CONFIG_IBSS_RSN=y, that can be used
to enable RSN support for IBSS. This links in RSN Authenticator code
from hostapd and adds code for managing per-peer information for IBSS. A
new wpa_cli command or driver event can be used to request RSN
authentication with an IBSS peer. New RSN Authenticator and Supplicant
will be allocated for each peer.
The basic state machine setup code is included in this commit, but the
state machines are not properly started yet. In addition, some of the
callback functions are not yet complete.
When using ap_scan=1, we know before the association request that MFP
will be supported, so we can as well require it. This helps mac80211 in
configuring whether to enable MFP.
It seems that for WPS registration we should use the same authentication
timeout as for ieee8021x, no? (See patch attached.) On slow platforms
public keys computation may take around 4-5 seconds (we actually stuck
on this issue).
Driver wrappers can now register global_init() and global_deinit()
driver_ops handlers to get a global data structure that can be shared
for all interfaces. This allows driver wrappers to initialize some
functionality (e.g., interface monitoring) before any interfaces have
been initialized.
Change association behavior to match with ap_scan=1 when WPS is used in
ap_scan=2 mode with wildcard SSID matching. In addition, allow hardcoded
BSSID to be used to select AP even if selected registrar attribute is
not present.
This adds support for setting of a regulatory domain to wpa_supplicant
drivers. It also adds regulatory domain setting for the nl80211 driver.
We expect an ISO / IEC 3166 alpha2 in the wpa configuration file as a
global.
Previously, this was only done when the new connection is using
WPA-Personal. However, it looks like it was possible to trigger an
infinite busy loop if altAccept or altReject were left set to true and
an EAPOL frame is received (eapolEap is set to true). Clearing altAccept
and altReject for each association prevents this loop from happening in
the beginning of the next association.
The wps_context data is now managed at wpa_supplicant, not EAP-WSC. This
makes wpa_supplicant design for WPS match with hostapd one and also
makes it easier configure whatever parameters and callbacks are needed
for WPS.
This adds WPS support for both hostapd and wpa_supplicant. Both programs
can be configured to act as WPS Enrollee and Registrar. Both PBC and PIN
methods are supported.
Currently, hostapd has more complete configuration option for WPS
parameters and wpa_supplicant configuration style will likely change in
the future. External Registrars are not yet supported in hostapd or
wpa_supplicant. While wpa_supplicant has initial support for acting as
an Registrar to configure an AP, this is still using number of hardcoded
parameters which will need to be made configurable for proper operation.
Find attached the patch that creates a new driver: roboswitch. This
driver adds support for wired authentication with a Broadcom
RoboSwitch chipset. For example it is now possible to do wired
authentication with a Linksys WRT54G router running OpenWRT.
LIMITATIONS
- At the moment the driver does not support the BCM5365 series (though
adding it requires just some register tweaks).
- The driver is also limited to Linux (this is a far more technical
restriction).
- In order to compile against a 2.4 series you need to edit
include/linux/mii.h and change all references to "u16" in "__u16". I
have submitted a patch upstream that will fix this in a future version
of the 2.4 kernel. [These modifications (and more) are now included in
the kernel source and can be found in versions 2.4.37-rc2 and up.]
USAGE
- Usage is similar to the wired driver. Choose the interfacename of
the vlan that contains your desired authentication port on the router.
This name must be formatted as <interface>.<vlan>, which is the
default on all systems I know.
A bug just got reported as a result of this for mac80211 drivers.
https://bugzilla.redhat.com/show_bug.cgi?id=459399
The basic problem is that since taking the device down clears the keys
from the driver on many mac80211-based cards, and since the mode gets
set _after_ the keys have been set in the driver, the keys get cleared
on a mode switch and the resulting association is wrong. The report is
about ad-hoc mode specifically, but this could happen when switching
from adhoc back to managed mode.
IEEE 802.11w/D6.0 defines new AKMPs to indicate SHA256-based algorithms for
key derivation (and AES-CMAC for EAPOL-Key MIC). Add support for using new
AKMPs and clean up AKMP processing with helper functions in defs.h.
This adds most of the new frame format and identifier definitions from IEEE
802.11w/D6.0. In addition, the RSN IE capability field values for MFP is
replaced with the new two-bit version with MFPC (capable) and MFPR
(required) processing.
Depending on how the driver implements IBSS searching and creation, it
may need to perform one or more scans before successfully completing the
association operation. Therefore, increase the timeout for IBSS
association operations so that the supplicant doesn't interrupt the
driver as much.
