This updates a previous patch did more or less the same thing by
providing the qosinfo as a single variable to the driver wrappers.
Signed-hostap: Jason Young <jason.young@dspg.com>
Add uapsd_queues and max_sp fields to sta_info struct,
and pass them to the sta_add callback.
These values are determined by the WMM IE in the (Re)Association Request.
Signed-off-by: Eliad Peller <eliad@wizery.com>
In some situations it might be benefical to send a unicast frame without
the need for getting it ACKed (probe responses for example). In order to
achieve this add a new noack parameter to the drivers send_mlme callback
that can be used to advise the driver to not wait for an ACK for this
frame.
Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
This offloads the station polling to driver wrappers, which may offload
it again to the driver. The hostap driver wrapper uses "real" data
frames while nl80211 uses null data frames.
Also add a specific event to indicate that a poll was successful for
future use with the nl80211 driver.
Remove the separate driver_ops functions set_cts_protect(),
set_preamble(), set_short_slot_time(), and set_ht_params(). These
belong into same set of operations as set_ap(), so there is no need
to maintain separate functions that just make the driver wrapper
more complex.
Since these have only been used with driver_nl80211.c, the driver_ops
can be removed immediately instead of maintaining backwards
compatibility period with the old functions.
This change is a first step in better supporting different driver
architectures for AP mode operations with nl80211. This commit in
itself does not add new functionality, but it makes it easier to add
new AP mode parameters to address needs of drivers that have more of
the MLME/SME in firmware or kernel.
When adding a new station, set the STA flags as part of the sta_add()
command. This ensures the flags are up to date when the station is added
by lower level drivers.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
This should fix EAPOL reauthentication and rekeying timeout issues
with Intel clients when using WMM (e.g., with IEEE 802.11n). These
stations do not seem to be able to handle EAPOL data frames as
non-QoS Data frames after the initial setup.
This adds STA flags to hapd_send_eapol() driver op to allow
driver_nl80211.c to mark the EAPOL frames as QoS Data frame
when injecting it through the monitor interface.
Getting rid of these inline functions seems to reduce the code size
quite a bit, so convert the most commonly used hostapd driver ops to
function calls.
This is not needed anymore and just makes things more difficult
to understand, so move the remaining function pointers to direct
function calls and get rid of the struct hostapd_driver_ops.
send_eapol, set_key, read_sta_data, sta_clear_stats,
set_radius_acl_auth, set_radius_acl_expire, and set_beacon
to use inline functions instead of extra abstraction.
Commit bf65bc638f started the path to
add this new abstraction for driver operations in AP mode to allow
wpa_supplicant to control AP mode operations. At that point, the
extra abstraction was needed, but it is not needed anymore since
hostapd and wpa_supplicant share the same struct wpa_driver_ops.
Start removing the unneeded abstraction by converting
send_mgmt_frame() to an inline function, hostapd_drv_send_mlme().
This is similar to the design that is used in wpa_supplicant and
that was used in hostapd in the past (hostapd_send_mgmt_frame()
inline function).
For now, this applies to the test command that can be used to set
periodic NoA (p2p_set noa). The value are stored and periodic NoA
is enabled whenever there are no non-P2P STAs connected to the GO.
There is no absolute requirement for separating address allocation
into separate functions, so simplify the driver wrapper interface
to use just if_add and if_remove instead of adding the new
alloc_interface_addr() and release_interface_addr() functions.
if_add() can now indicate if the driver forced a different interface
name or address on the virtual interface.
This patch allows the nl80211 driver to create its own per-bss context
and pass it to the drv_priv pointer of the hostapd bss state.
With this and the following patch, stations can associate to and switch
between multiple BSS interfaces of a single wiphy.
This obsoletes a few instances of passing ifname to a callback, those
can be removed in a separate patch.
It might also be useful to move more fields from the driver data to the
per-bss data structure in the future.
