If the p2p_group_add command does not specify the operating channel,
make sure the operating channel set in the configuration file meets
the P2P requirements in the same way as is done with the frequency
specified as the command parameter.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The WPA/RSN IE in EAPOL-Key 2/4 is more reliable than the one in
(Re)Association Request frame. Update the STA info base don the
EAPOL-Key frame so that the correct cipher information is used
even if the (Re)Association Request frame is missing or corrupted
in the capture.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When the driver (or firmware) implements AP mode SME, the use of raw
management frame TX functions is not working properly at the moment. As
an initial step, convert these AP mode operations to use
NL80211_CMD_DEL_STATION and do not claim that driver provides TX status
for deauth/disassoc frames. While this does not address all use cases
(e.g., reason code is not specified in the command), this fixes number
of issues where the station does not get disconnected properly.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Group properties are now accessible individually. The function to retrieve
the dictionary containing the group properties is removed in favor of the
individual functions. The group member properties are removed as well as
they erroneously retrieved the group properties via the old function.
Signed-hostap: Todd Previte <toddx.a.previte@intel.com>
Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
intended-for: hostap-1
After reallocation of the bss struct, current_bss wasn't updated and
could hold an invalid pointer (which might get dereferenced later).
Update current_bss if the pointer was changed.
Signed-hostap: Eliad Peller <eliad@wizery.com>
intended-for: hostap-1
Commit 30680e9332 changed the length
of the implicit challenge result to match with the exact length used
in TTLS. However, it failed to update the peer_challenge generation
to use a separate random value. Previously, this was generated as
part of the implicit challenge, but more correct way would have been
to generate a random value for it separately. Do this now to fix the
read after the allocated buffer (16 bytes after the implicit
challenge).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
If multiple station mode radios are bridged together on the same device,
it is possible for wpa_supplicant to receive EAPOL frames from the
bridge interface and then process them separately for each interface.
This can results in problems since multiple instances of supplicant side
could end up trying to process a single 4-way handshake. Avoid this
problem by filtering bridge interface EAPOL RX based on the desctination
MAC address. It should be noted that this works only when unicast
addresses are used (e.g., with WLAN) and not with the IEEE 802.1X EAPOL
group address (e.g., most wired networks).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use separate mnc_len parameter instead of expecting the imsi parameter
to be in special MCC|MNC|-|<MSIN> format to make this function more
generic.
Signed-hostap: Jouni Malinen <j@w1.fi>
This DO has a maximum length of 127 bytes (TS 102 221), so better use
large enough buffer when reading the record.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows Interworking network selection to be used with EAP-TLS
(client certificate/private key based credential).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, this provisioning info was cleared using the P2P Interface
Address of the GO as the key. That did not always work in the case the
where we joined an already running group. This could result in the next
connection to that same GO skipping provision discovery. Fix this by
finding the peer entry based on its P2P Device Address instead of the
P2P Interface Address which may not always be set.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
Commit 6bf731e8ce broke handling of
EVENT_CHANNEL_LIST_CHANGED by introducing a cached copy of the driver
channel list that does not get updated even if driver changes its list.
Fix this by synchronizing the cacched wpa_s->hw.modes information
whenever EVENT_CHANNEL_LIST_CHANGED is processed. This fixes P2P channel
list updates based on regulatory domain hints that may trigger driver to
change its supported channel list.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
When wpa_supplicant disconnects, e.g., due to authentication timeout,
we need to go through the EVENT_DISASSOC/DEAUTH processing similarly
to the driver triggered cases to get correct events delivered to the
ctrl_iface. Fix this by calling wpa_supplicant_event() in these cases
and by filtering out the confusing CTRL-EVENT-DISCONNECTED event with
all zeros BSSID.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If a GO Negotiation peer is found, wpas_p2p_stop_find() stops the
negotiation and p2p_cancel can return success.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If a wildcard PIN is used on any of the radios that hostapd is
controlling, invalidate the matching PIN on all the other radios
to avoid multiple uses of the same PIN.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since P2P GO cannot change the SSID after WPS provisioning step, we
can use the specific SSID for the scan for data connection. In addition,
mark this as p2p_probe to avoid unnecessary use of 802.11b rates.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Copy the SSID and frequency of the selected group into go_params in
join-a-running-group case so that the scan optimization can be used for
the provisioning step similarly to the case of group formation. This
uses a specific SSID and a single channel scan to avoid unnecessary
frames during the step.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since the P2P client learns the SSID of the group during GO Negotiation,
use the specific SSID in the Probe Request frames during the
provisioning step. This helps in avoiding unnecessary Probe Response
frames from other P2P GOs or APs.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use Device Password ID in WSC IE of Probe Request and Probe Response
frames to advertise immediate availability of WPS credentials per P2P
specification sections 3.1.2.1.1 (Listen State), 3.1.2.1.2 (Scan Phase),
and 3.1.2.1.3 (Find Phase).
For now, the Device Password ID is set only for the case where we are
active GO Negotiation with a specific peer. In practice, this means that
the Probe Response frames during pending GO Negotiation (whenever in
Listen state) indicate availability of the credential.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_flush did not explicit stop all P2P operations, i.e., the exact
behavior depended on the P2P module state at the time the p2p_flush
command was issued. Make this more consistent by explicitly calling
p2p_stop_find() from p2p_flush().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If Listen state was in progress on another channel when a request to
send an Action frame (e.g., Provision Discovery Request or Invitation
Request to a peer on the peer's Listen channel that is different from
our Listenc hannel) is issued, wpa_supplicant tried to use concurrent
remain-on-channel operations. While some drivers can handle this
cleanly, there are drivers that don't and wpa_supplicant is not expected
to request concurrent remain-on-channel operations.
Fix this by cancelling the ongoing remain-on-channel with stop_listen
prior to sending the Action frame on another channel. If a P2P search
was in progress, it will be continued after the timeout on the new
operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This also disables WPS support if hidden SSID is enabled in AP mode.
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new venue_name configuration parameter can now be used to configure
the ANQP Venue Name values that stations can request through GAS.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds GAS/ANQP implementation into hostapd. This commit brings in
the basic GAS/ANQP functionality, but only the ANQP Capability List
element is supported.
For testing purposes, hostapd control interface SET command can be used
to set the gas_frag_limit parameter dynamically.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
New global configuration parameters pcsc_reader and pcsc_pin can now be
used to initialize PC/SC reader context at start of wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
Definition of ANonce selection in IEEE Std 802.11i-2004 is somewhat
ambiguous. The Authenticator state machine uses a counter that is
incremented by one for each 4-way handshake. However, the security
analysis of 4-way handshake points out that unpredictable nonces help in
preventing precomputation attacks. Instead of the state machine
definition, use an unpredictable nonce value here to provide stronger
protection against potential precomputation attacks.
Signed-hostap: Jouni Malinen <j@w1.fi>
These are from Android wpa_supplicant_8.git initial 0.8.X commit
8d520ff1dc2da35cdca849e982051b86468016d8 with some additional edits and
renaming of .config files to android.config.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This can be used to disable wpa_supplicant controlled roaming. It should
be noted that the WPA_DRIVER_FLAGS_BSS_SELECTION capability is the
preferred way for this and CONFIG_NO_ROAMING should be obsoleted once
drivers support the new NL80211_ATTR_ROAM_SUPPORT capability
advertisement.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Move disassociate and deauthenticate commands to ctrl_iface_ap.c, so
that they ares accessible for wpa_supplicant AP mode and wpa_cli (with
CONFIG_AP option enabled).
Signed-hostap: Jithu Jance <jithu@broadcom.com>
The org.freedesktop.DBus.Properties interface is now supported for peer
properties. Ensure that GetAll will work by having the IEs property
function return NULL data instead of a failure until it is implemented.
Signed-hostap: Reinette Chatre <reinette.chatre@intel.com>
intended-for: hostap-1
Commit 3f6e50ac28 made it possible to access
P2P peer properties using the org.freedesktop.DBus.Properties interface.
While maintaining the original intent of that patch we make two changes
to it here:
First, 3f6e50ac28 changed the type used to
represent the WPS vendor extension data from bytes to a string. In
addition to the type change the way in which the vendor extension data
was provided to the function creating the string was incorrect and would
not present the correct vendor extension data even in string format.
Revert the type change made in 3f6e50ac28
and present the WPS vendor extension data as an array of an array of
bytes as it was before.
Second, 3f6e50ac28 changes the secondary
device types representation from an array of an array of bytes to an
array of bytes. Revert that change to make secondary device types
accessible via an array of an array of bytes again.
Signed-hostap: Reinette Chatre <reinette.chatre@intel.com>
intended-for: hostap-1
