These values are used with WAPI and CCX and reserving the definitions
here reduces the number of merge conflicts with repositories that
include these functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
This introduces new AKM for SAE and FT-SAE and adds the initial parts
for going through the SAE Authentication frame exchange. The actual SAE
algorithm and new fields in Authentication frames are not yet included
in this commit and will be added separately. This version is able to
complete a dummy authentication with the correct authentication
algorithm and transaction values to allow cfg80211/mac80211 drivers to
be tested (all the missing parts can be handled with
hostapd/wpa_supplicant changes).
Signed-hostap: Jouni Malinen <j@w1.fi>
Otherwise it's difficult to determine if the supplicant was built with
CONFIG_AP, CONFIG_IBSS_RSN, CONFIG_P2P, etc. CONFIG_AP and CONFIG_P2P
can be inferred from the introspection data of the Interface object,
but CONFIG_IBSS_RSN does not change the introspection data at all and
thus it's impossible to determine whether the supplicant supports it
without knowing its compile-time options.
Signed-hostap: Dan Williams <dcbw@redhat.com>
intended-for: hostap-1
The wpa_s->p2p_in_provisioning flag did not get cleared in some cases
where p2p_cancel command is used to stop group formation. This can result
in some operations (like p2p_find) failing afterwards. Fix this by using
wpas_group_formation_completed() when processing p2p_cancel for a group
that has not yet completed group formation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the keystore:// prefix is used in the private_key entry, convert that
to the OpenSSL engine style configuration used for Android JB keystore.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The pending GAS entry must be removed from the list when it is removed.
This fixes an issue with potential segfault due to freed memory being
accessed if the driver fails to accept a GAS query.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
External programs can use this new parameter to prevent wpa_supplicant
from connecting to a list of BSSIDs and/or SSIDs. The disallowed BSSes
will still be visible in scan results and it is possible to run ANQP
operations with them, but BSS selection for connection will skip any
BSS that matches an entry in the disallowed list.
The new parameter can be set with the control interface SET command
using following syntax:
SET disallow_aps <disallow_list>
disallow_list ::= <ssid_spec> | <bssid_spec> | <disallow_list> | “”
SSID_SPEC ::= ssid <SSID_HEX>
BSSID_SPEC ::= bssid <BSSID_HEX>
For example:
wpa_cli set disallow_list "ssid 74657374 bssid 001122334455 ssid 68656c6c6f"
wpa_cli set disallow_list
(the empty value removes all entries)
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows hostapd_cli and wpa_cli all_sta command to be used to
display connected time (in seconds) of each station in AP mode.
Signed-hostap: Raja Mani <rmani@qca.qualcomm.com>
Commit 6b56cc2d97 added clearing of the
p2p->pending_action_state too early in this function. This should not
be done if we are going to silently ignore the frame due to dialog
token mismatch. Fix this by moving the code around to check the dialog
token first.
This issue resulted in PD Request retries getting stopped too early if
the peer is sending out an unexpected PD Response (e.g., because of it
being excessively slow with the response so that the response is
received only after the next TX attempt with a new dialog token).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for the P2P client group to be removed while waiting for
a pending scan operation (e.g., when p2p_group_idle timeout hits after
getting disconnected from the GO with something else than
Deauthentication with reason code 3). If this happens with a P2P
interface that is used both for P2P Device and group roles, scan state
could get stuck while waiting for the next scan to complete since no
more station (P2P client) mode scans are scheduled. Fix this by clearing
sta_scan_pending when removing the temporary group network block.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Make Invitation process for re-invoking a persistent group behave
similarly to GO Negotiation as far as channel negotiation is concerned.
The Operating Channel value (if present) is used as a starting point if
the local device does not have a forced operating channel (e.g., due to
concurrent use). Channel lists from devices are then compared to check
that the selected channel is in the intersection. If not, channel is
selected based on GO Negotiation channel rules (best channel preferences
etc.). Invitation Request is rejected if no common channel can be
selected.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If two P2P_FIND commands and a station mode SCAN command are issued in a
sequence with the second P2P_FIND and SCAN commands started before the
initial scan from the first P2P_FIND command has completed,
sta_scan_pending may be left set without an automatic way of getting it
cleared. This can get P2P search stuck if no further station mode scan
operations are run.
Fix this by clearing the sta_scan_pending flag whenever station mode scans
are stopped due to no enabled networks resulting in INACTIVE mode getting
entered. In addition, avoid setting sta_scan_pending flag when a special
scan_res_handler is set so that this does not get enabled on the P2P
Device interface during a P2P search operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If there are any disabled networks, show a debug print with the count
of those networks when no enabled networks are found. This can be
helpful in trying to figure out why scans are being skipped.
Signed-hostap: Jouni Malinen <j@w1.fi>
The ASCII hexdump is somewhat difficult to search for (especially on
Android builds), so make the debug log easier to parse by printing the
full control interface command as a text string. In addition, use
wpa_dbg() to get the interface name printed so that multi-interface
cases can be debugged.
Signed-hostap: Jouni Malinen <j@w1.fi>
Setting just ssid->passphrase is not enough to complete the network
block for the GO entry. Also the PSK needs to be derived so that the
network is considered enabled by wpas_network_disabled(). The previous
version worked as long as something else allowed the scan request to be
performed (this is needed even though the actual scan is skipped when
starting GO).
The first GO start was allowed because wpa_s->scan_req is initialized to
1 in wpa_supplicant_alloc(). However, other attempts may fail if
wpa_s->scan_req is cleared. This failure shows up as "No enabled
networkas - do not scan" in debug log followed by state change to
INACTIVE when trying to start GO.
Fix this by deriving PSK from the passphrase for GO mode.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 30ee769235 started skipping P2P
group removal if wpa_s->current_ssid is not set and commit
0d30cc240f started clearing
wpa_s->current_ssid on disconnection. This combination broke
p2p_group_idle timeout on P2P client interface in a case where no
separate P2P group interface is used and when the disconnection is
triggered by something else than an explicit indication of GO
terminating the group.
Fix this by relaxing network block matching rules when figuring out
whether any of the configured network blocks could be in P2P use. The
p2p_group flag alone should be enough for this since temporary P2P group
network blocks are removed once the P2P group is terminated.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the AP creation failed (missing freq= or driver error) the supplicant
would previously stay in SCANNING state forever. Instead, it should
handle the error a bit better and drop back to DISCONNECTED so clients
know something went wrong.
Signed-hostap: Dan Williams <dcbw@redhat.com>
intended-for: hostap-1
As long as WLAN_STA_ASSOC_REQ_OK is set in sta->flags, Class 3 frames do
not trigger a disassoc/deauth. If it is still set even after the assoc
response tx has already failed, it may take somewhat longer for clients
to realize that the connection wasn't fully established.
Signed-hostap: Felix Fietkau <nbd@openwrt.org>
Channel 14 is available only in Japan and is DSSS-only according to
IEEE 802.11-2012 19.4.3 and MIC Equipment Ordinance (EO)
for Regulating Radio Equipment article 49.20.
At the same time, P2P should avoid using DSSS modulation in normal
operation according to P2P specification v1.2 2.4.1.
Signed-hostap: Mykyta Iziumtsev <mykyta.iziumtsev@gmail.com>
intended-for: hostap-1
This avoids extra latency caused by establishing an aggregation session
and makes the initial connection attempt more reliable
Signed-hostap: Felix Fietkau <nbd@openwrt.org>
This patch fixes an issue where removing a WDS VLAN interface also
removed the main AP interface from the same bridge.
Signed-hostap: Felix Fietkau <nbd@openwrt.org>
Commit 4d32c0c44d added another use for the
local pos variable and that broke the mechanism used to determine wheter
the peer address was provided. Fix this by using a separate pointer to the
peer address.
Signed-hostap: Jouni Malinen <j@w1.fi>
When I use CONFIG_WPS_NFC=y a warning appears.
wps_supplicant.c:1872:12: warning: 'wpas_wps_add_nfc_password_token'
defined but not used [-Wunused-function]
This patch removes this warning.
Signed-hostap: Masashi Honma <masashi.honma at gmail.com>
If a connection operation is started on an interface based on scan
results, other virtual interfaces should not be information about the
results to avoid potential concurrent operations during the association
steps. Since the sibling notification of scan results received was added
as an optimization, skipping it for this type of cases is the simplest
way of avoiding unnecessary concurrent operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes sure that the interrupted station mode scan can be completed
after the P2P operations have had their chance of using the radio.
Signed-hostap: Jouni Malinen <j@w1.fi>
Driver could reject the new scan based on any virtual interface
running a concurrent scan. As such, mark the pending scan callback
for P2P based on any interfaces instead of just the one used for
the p2p_scan operation.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since we have a global P2P module, the flag to trigger scan completion
events to it needs to be in similar context. The previous design
maintained this separately for each virtual interface and if P2P module
did not run its scan operation on the virtual interface that completed
the scan, P2P module would not be allowed to restart operations
properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
The BSS pointer may change if the entry needs to be reallocated
and the new pointer has to be added to the last_scan_res array
to avoid using pointers to freed memory.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is a generic AES CCM implementation that can be used for other
purposes than just implementing CCMP, so it fits better in a separate
file in src/crypto.
Signed-hostap: Jouni Malinen <j@w1.fi>
Now that the internal AES implementation supports 256-bit keys, enable
use of the TLS cipher suites that use AES-256 regardless of which crypto
implementation is used.
Signed-hostap: Jouni Malinen <j@w1.fi>
AES uses the same 128-bit block size with 128, 192, 256 bit keys, so use
the fixed block size definition instead of trying to dynamically set the
block size based on key length. This fixes use of 192-bit and 256-bit
AES keys with crypto_cipher_*() API when using the internal AES
implementation.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is otherwise identical to aes_gcm_ae() but does not use the
plain/crypt pointers since no data is encrypted.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds 192-bit and 256-bit key support to the internal AES
implementation and extends the AES-GCM functions to accept key length to
enable longer AES key use.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is a generic AES GCM and GMAC implementation that can be used for
other purposes than just implementing GCMP, so it fits better in a
separate file in src/crypto.
Signed-hostap: Jouni Malinen <j@w1.fi>
There is no need to allocate a temporary buffer and build GHASH input
data into it. Instead, ghash() is trivial to split into update part that
can be called separately for each segment.
Signed-hostap: Jouni Malinen <j@w1.fi>
GCMP encodes length of AAD differently, so remove the unnecessary
code that got copied from the CCMP implementation.
Signed-hostap: Jouni Malinen <j@w1.fi>
