The Linux kernel commit 113f3aaa81bd ("cfg80211: Prevent regulatory
restore during STA disconnect in concurrent interfaces") broke the
regulatory clearing attempt in this test case since
cfg80211_is_all_idle() is now returning false due to the AP interface
being up and that results in the Country IE -based regulatory
information not getting cleared back to defaults.
Work around this by stopping the AP interface first so that when the
station interface receives the disconnection, there are no other active
interfaces in the system. In addition, wait for REGDOM event for the
Country IE hint after association to avoid disconnection before the
regulatory events have been fully processed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Perform detailed tests with OCV enabled, for both the 4-way and group
key handshakes. These tests include establishing a working connection
with OCV enabled, assuring that a STA without OCV enabled can still
connect to a STA with OCV enabled (and vice versa), verifying that
invalid OCI elements get silently ignored, verifying that missing OCI
elements are reported, and so on.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Verify that EAP-AKA' client rejects Challenge with an appended AT_KDF
and a modified AT_KDF value during KDF negotiation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new wpa_supplicant network parameter group_mgmt can be used to
specify which group management ciphers (AES-128-CMAC, BIP-GMAC-128,
BIP-GMAC-256, BIP-CMAC-256) are allowed for the network. If not
specified, the current behavior is maintained (i.e., follow what the AP
advertises). The parameter can list multiple space separate ciphers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to attach the monitor interface was events when issuing
only a single INTERFACES command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for the P2P-GROUP-STARTED event to get delayed more than
one second especially when the GO Negotiation responder becomes the P2P
Client and the system is heavily loaded. Increase the default timeout
for the expected success case from 1 to 5 seconds to avoid failing test
cases that would have succeeded if given a bit more time to complete the
exchange.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Some operations take longer time on real hardware than on hwsim. This
commit increases two timeouts so that the tests will pass on real
hardware, too.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
Use increased timeouts for connect and disconnect since these operations
take a longer time on real harware than they do on hwsim.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
The generic cmd_execute() function was introduced in a manner that
converted the argument array to a string and used shell to run the
command unconditionally. This is not really desirable, so move back to
using the command array by default and use the single command string
with a shell only when really needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add the feature to execute shell commands on each wpa_supplicant/hostapd
interface host. When executing remote tests the interfaces are not all
on a single host so when executing shell commands the test needs to
execute the command on the host which the interface relevant for the
command is on. This patch enables tests to execute the command on the
relevant host.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
Start using the wpa_supplicant remote UDP interface for the control and
monitor sockets for P2P group interfaces so that P2P tests would work on
real hardware. Also have the group requests and events show in the test
log with the hostname and the interface name of the group interface.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
Commit afb2e8b891 ('tests: Store P2P
Device ifname in class WpaSupplicant') did not take into account the
possibility of capa.flags not existing in get_driver_status() and broke
WEXT test cases. Fix this by checking that capa.flags is present before
looking at its value.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is a regression test case to verify that MTK is calculated properly
also in this unexpected sequence.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Modify the persistent_group_profile_add test to support configurations
that use a dedicated P2P Device interface by sending the ADD_NETWORK and
SET_NETWORK commands on the global control interface and specifying the
P2P Device interface name.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add an attribute to class WpaSupplicant with the name of the
P2P Device interface. If a separate interface is not used for
P2P Device, this attribute will hold the name of the only used
interface (with functions also as the P2P Device management
interface).
This attribute will be used to direct P2P related commands to the
P2P Device interface, which is needed for configurations that use
a separate interface for the P2P Device.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
It is better to use a list of command line arguments for the local
execution case and convert that to a space-separated string for the
remote case.
Signed-off-by: Jouni Malinen <j@w1.fi>
The no self.global_iface case was not returning the result from the
self.request() case. While this is not really a path that is supposed to
be used, make it return the response since it is at least theoretically
possible to get here.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the dump_monitor() call to drop a P2P-GO-NEG-FAILURE
event that was indicated quickly after the P2P_CONNECT command was
issued. This could result in grpform_reject test case failing to see the
expected event and fail the test due to "Rejection not reported".
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This parameter is used only in couple of test cases and there is no need
to maintain the code to reset it in WpaSupplicant::reset().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This parameter is used only in couple of test cases and there is no need
to maintain the code to reset it in WpaSupplicant::reset().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This parameter is used only in couple of test cases and there is no need
to maintain the code to reset it in WpaSupplicant::reset().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This parameter is used only in couple of test cases and there is no need
to maintain the code to reset it in WpaSupplicant::reset().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This parameter is used only in couple of test cases and there is no need
to maintain the code to reset it in WpaSupplicant::reset().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
