When an EVENT_SIGNAL_CHANGE occurs the bgscan is informed about this
change but the new RSSI value is not stored. In consequence, when
roaming candidates are evaluated, the RSSI value of the current BSS used
to compare is an old one obtained during the last scan rather than the
new one given by the signal change event. This leads sometimes to bad
decision when selecting a new BSS for roaming.
This patch solves the issue by updating the current BSS level when
receiving a signal change event in order to have a very up-to-date
current signal value when choosing an new BSS.
Signed-off-by: Matthieu Mauger <matthieux.mauger@intel.com>
When stopping the TKIP countermeasures, it would be preferable to
connect immediately. However if scheduled scan is in progress,
a connection attempt will be done only when scan results are received,
so cancel the scheduled scan to allow immediate scan and connection
attempt.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Read p2p_go_ctwindow (0-127 TUs) from the config file, and pass it to
the driver on GO start.
Use p2p_go_ctwindow=0 (no CTWindow) by default.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
In addition, add support for returning the capability list through
the BSS control interface command.
Signed-off-by: ASHUTOSH NARAYAN <ashutoshx.narayan@intel.com>
In addition, add support for returning the capability list through the
BSS control interface command.
Signed-off-by: ASHUTOSH NARAYAN <ashutoshx.narayan@intel.com>
Instead of calling a dummy printf function use preprocessor to determine
if debugging mode is enabled. Also use native Qt debug function.
Signed-off-by: Arkadiusz Bokowy <arkadiusz.bokowy@gmail.com>
If a matching IBSS is found in scan results, change requested frequency
to match and disable OBSS scan.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Add fixed_freq=<0/1> network block parameter and pass it to the driver
when starting or joining an IBSS. If this flag is set, IBSS should not
try to look for other IBSS networks to merge with on different channels.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
The new reassoc_same_bss_optim=1 configuration parameter can now be used
to request wpa_supplicant to bypass the unnecessary Authentication frame
exchange when reassociating back to the same BSS with which the device
is already associated. This functionality is disabled by default since
it may cause undesired interoperability issues with some APs.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit c35e35ed81 ('Add passive_scan
configuration parameter') used incorrect parameter name when writing the
passive_scan parameter into a configuration file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new "DUMP" and "SET <variable>" control interface commands can be
used to fetch global wpa_supplicant configuration parameters.
Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
This can be used to provide more control to upper layers on network
blocks generated as part of Interworking network selection.
INTERWORKING_ADD_NETWORK behaves otherwise identically to
INTERWORKING_CONNECT, but it does not request a new connection after
having added the network block and it returns the network id of the
added network.
INTERWORKING_ADD_NETWORK followed by REASSOCIATE would behave more or
less identically to INTERWORKING_CONNECT, but this allows the created
network profile to be modified, if desired, and/or stored externally.
SELECT_NETWORK can also be used with the network id returned from
INTERWORKING_ADD_NETWORK to enforce that specific network profile to be
used for the next connection (though, it should be noted that this
behavior may not meet all Hotspot 2.0 requirements if there were other
enabled networks that could have higher priority).
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit b31be3a0fd ('P2P: Add automatic GO
Negotiation vs. join-a-group selection') added this P2P_CONNECT 'auto'
parameter, but did not update any documentation on it.
Signed-off-by: Jouni Malinen <j@w1.fi>
If a separate P2P group interface was used, P2P_CONNECT-auto fallback to
GO Negotiation could result in use of freed memory and segmentation
fault. This happened in cases where the peer GO was found in some old
scans, but not in the first scan triggered by the P2P_CONNECT-auto
command ("P2P: Peer was found running GO in older scan -> try to join
the group" shows up in the debug log). In addition, the GO would still
need to reply to PD Request to allow this code path to be triggered.
When five scans for the GO were completed in this sequence, the P2P
group interface was removed as part of falling back to GO Negotiation.
However, that ended up dereferencing the freed wpa_s instance at the end
of scan event processing. Fix this by reordering code a bit and breaking
out from EVENT_SCAN_RESULTS processing if the interface could have been
removed.
Signed-off-by: Jouni Malinen <j@w1.fi>
When SAE authentication fails, wpa_supplicant retries four times. If all
the retries result in failure, SAE state machine enters BLOCKED state.
Once it enters this state, wpa_supplicant doesn't retry connection. This
commit allow connection retries even if the state machine entered
BLOCKED state.
There could be an opinion "Is this patch needed? User could know the SAE
state machine is in the BLOCKED mode by MESH-SAE-AUTH-BLOCKED event.
Then user can retry connection. By user action, SAE state machine can
change the state from BLOCKED to another.". Yes, this is a true at the
joining mesh STA. However, a STA that is already a member of existing
mesh BSS should not retry connection because if the joining mesh STA
used wrong password, all the existing STA should do something from UI to
retry connection.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Send MESH-SAE-AUTH-BLOCKED event if SAE authentication is blocked. The
BLOCK state will finish when a new peer notification event is sent for
the same MAC address.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
SAE authentication fails likely with wrong password. This commit adds a
notification of the failure to the upper application (UI) so that the
application can notify suspection of a wrong password to the user. The
control interface monitor even for this is "MESH-SAE-AUTH-FAILURE
addr=<peer>".
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Commit 07cb45ccb2 ('mesh: Add no_auto_peer
config option') added a new struct wpa_ssid argument and added an
unnecessary parsing and setting of the value in
wpa_supplicant_ctrl_iface_update_network(). This is not needed since
wpa_config_set() takes care of parsing the parameters.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for a network profile to change its type from P2P
persistent group to a normal network and back. The D-Bus interface uses
different types of objects for those, so the object needs to
re-registered in case of type change. This fixes issues in leaving
behind an incorrect type of object and leaking memory when freeing such
a network block that has had its disabled parameter changed.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is a chance that wpa_supplicant may get killed during
the time it is writing config file. If this happens, user
information like SSIDs and passwords can be lost forever.
This change works around that by writing config to a
temporary file and then renaming the file to the correct name.
Signed-off-by: Vinit Deshpande <vinitd@google.com>
We should not enable HT if WEP or TKIP is configured.
Without the patch and WEP configuration we will get message:
Association request to the driver failed
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Do not claim to change the Listen channel in a debug message when
previously configured channel prevents this. In addition, fix a typo in
another related debug print.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The pending interface created during provision discovery should
not be removed on stopping p2p_find. This pending interface has
to be used after completing GO negotiation. Earlier the pending
interface is created just before GO negotiation so there was no
problem.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to allow P2PS related new control interface commands to
be redirected for proper context processing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If P2PS config method is used for provisioning, upon forming a new GO,
start WPS registrar for the provisioned peer automatically.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This introduces a P2P module callback function that will be used to
create the pending P2PS group after sending PD Response and receiving
ACK status for it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When the peer device is trying to form a new group despite having
old persistent group with same roles, remove the stale persistent
group.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds new wpa_supplicant control interface commands
P2P_ASP_PROVISION and P2P_ASP_PROVISION_RESP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpas_p2p_prov_disc() implementation to accept P2PS
parameters. None of the callers are yet using this functionality; the
following commit introduces a user.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a data structure for storing P2PS PD information and code to
add the related attributes into PD Request. The actual operation to
trigger this behavior will be added in a separate commit.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support to parse received GAS requests for ASP services and
prepare GAS responses accordingly.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the P2P_SERV_DISC_REQ control interface command with a new
"asp" service type. This takes service id, service string, and optional
service info as arguments.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In addition, add a new P2P_SERVICE_REP command that can be used to
replace existing ASP advertisements.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This provides additional WPS definitions and rules for negotiating use
of P2PS default PIN configuration method.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
P2PS seek strings can now be specified in the P2P_FIND control interface
command with one or more optional "seek=<str>" parameters.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for a Action frame sequence completion to stop an
ongoing offchannel remain-on-channel operation unexpectedly in cases
where TX operation was offloaded to the driver and such an operation
happened to occur during a previously started remain-on-channel (e.g.,
for P2P listen state).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the previously requested remain-on-channel for P2P
listen state to get canceled before having received driver event
indicating start of that remain-on-channel operation. In such a case,
the event was able to trigger P2P module to start processing listen
timeout even though there was not supposed to be a following listen
operation anymore. Skip the driver event if we are not waiting for a new
listen state.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When noise floor measurements are not available, compute SNR
using default values for the noise floor. This helps steer us
towards 5 GHz BSSes in high signal strength environments.
In more detail...
Existing code prefers a 5 GHz BSS when the 5 GHz BSS's signal
strength is "close" to that of the 2.4 GHz BSS, or when both SNRs
are large. However, the mwifiex driver does not provide noise
floor measurements, so we can't compute SNRs.
Because mwifiex doesn't provide NF measurements, the "large SNR"
code wasn't effective. By using default values for the noise floor,
we can again compute SNRs, and decide that the SNR is high enough
that we shouldn't worry about the exact difference in SNR.
The default noise floor values (one for 2.4 GHz, and one for 5 GHz)
were chosen by measurement in a noisy environment, so they should be
conservative.
Note that while this patch is motivated by mwifiex, it affects
ath9k as well. Although ath9k provides noise floor measurements
in general, it will sometimes fail to provide a measurement for
one or more specific channels.
As a result of this patch, we'll always compare BSSes based on SNR
(either measured or estimated), rather than sometimes comparing
based on signal strength. ("Always" assumes that the
WPA_SCAN_LEVEL_DBM flag is set. It is for mwifiex and ath9k.)
While there:
- fix a whitespace issue (spaces -> tab)
- clean up existing comments
- update dump_scan_res to indicate whether the noise floor is
measured, or default
Signed-hostap: mukesh agrawal <quiche@chromium.org>
For wired IEEE 802.1X authentication, phase1="allow_canned_success=1"
can now be used to configure a mode that allows EAP-Success (and
EAP-Failure) without going through authentication step. Some switches
use such sequence when forcing the port to be authorized/unauthorized or
as a fallback option if the authentication server is unreachable. By
default, wpa_supplicant discards such frames to protect against
potential attacks by rogue devices, but this option can be used to
disable that protection for cases where the server/authenticator does
not need to be authenticated.
When enabled, this mode allows EAP-Success/EAP-Failure as an immediate
response to EAPOL-Start (or even without EAPOL-Start) and EAP-Success is
also allowed immediately after EAP-Identity exchange (fallback case for
authenticator not being able to connect to authentication server).
Signed-off-by: Jouni Malinen <j@w1.fi>
