Use shared functions for converting Primary Device Type between binary
and string formats. In addition, use array of eight octets instead of a
specific structure with multiple fields to reduce code complexity.
Mainly, this is including header files to get definitions for functions
which is good to verify that the parameters match. None of these are
issues that would have shown as incorrect behavior of the program.
The WPS 1.0h specification is quite unclear on what exactly should be
used as the MAC Address value in the Credential and AP Settings. It
looks like this should after all be the MAC Address of the Enrollee,
so change Registrar implementation to use that address instead of the
AP BSSID.
In addition, add validation code to the Enrollee implementation to
check the MAC Address value inside Credential (and also inside AP Settings)
to make sure it matches with the Enrollee's own address. However, since
there are deployed implementations that do not follow this interpretation
of the spec, only show the mismatch in debug information to avoid breaking
interoperability with existing devices.
Previously, WSC_MSG was hardcoded for every message from ER, but
this needs to be changed based on message type to send a valid
message to the Enrollee via EAP transport.
New PINs can now be added to WPS ER. This results in the ER code
using SetSelectedRegistrar to modify AP state so that Enrollees
will be able to notice the actice registrar more easily.
Though we have such a timeout when handling SetSelectedRegistrar UPnP
message from an external registrar, it looks like we don't have one when
the internal registrar is activated for PIN connection. Thus we set the
SelectedRegistrar flag when AP is activated for PIN connection but we
never reset it - not by some timeout, nor when registration succeeds.
This lead to situations where AP everlastingly declare that it is
activated for WPS PIN connection when in reality it is not.
Use the same timeout (and also success with PIN) to clear the selected
registrar flag when using internal registrar, too.
If PBC session overlap is detected during an ongoing PBC protocol run,
reject the run (if M8, i.e., credentials, have not yet been sent). This
provides a bit longer monitoring time at the Registrar for PBC mode to
catch some cases where two Enrollees in PBC mode try to enroll
credentials at about the same time.
This provides information about PBC mode result from the WPS Registrar
module. This could be used, e.g., to provide a user notification on the
AP UI on PBC failures.
If PBC session overlap is detected between button press on the registrar
and M1 is reception, report session overlap with the Config Error
attribute in M2D to the Enrollee.
Store a copy of device attributes during WPS protocol run and make it
available for external programs via the control interface STA MIB
command for associated stations. This gives access to device name and
type which can be useful when showing user information about associated
stations.
wpa_supplicant can now reconfigure the AP by acting as an External
Registrar with the wps_reg command. Previously, this was only used
to fetch the current AP settings, but now the wps_reg command has
optional arguments which can be used to provide the new AP
configuration. When the new parameters are set, the WPS protocol run
is allowed to continue through M8 to reconfigure the AP instead of
stopping at M7.
Since we do not currently support changing the AP settings received
from M7, there is no point in actually sending out the M8 that would
likely trigger the AP to reconfigure itself and potentially reboot.
For now, we just receive the AP settings in M7 and add a local network
configuration block based on those, but NACK the message. This makes
wps_reg work like wps_pin, but by using the AP PIN instead of a client
PIN.
hostapd_cli wps_pin command can now have an optional timeout
parameter that sets the PIN lifetime in seconds. This can be used
to reduce the likelihood of someone else using the PIN should an
active PIN be left in the Registrar.
Some deployed implementations seem to advertise incorrect information
in this attribute. For example, Linksys WRT350N seems to have a
byteorder bug that breaks this negotiation. In order to interoperate
with existing implementations, assume that the Enrollee supports
everything we do.
Update credential to only include a single authentication and
encryption type in case the AP configuration includes more than one
option. Without this, the credential would be rejected if the AP was
configured to allow more than one authentication type.
Windows XP and Vista clients can get confused about EAP-Identity/Request
when they probe the network with EAPOL-Start. In such a case, they may
assume the network is using IEEE 802.1X and prompt user for a
certificate while the correct (non-WPS) behavior would be to ask for the
static WEP key. As a workaround, use Microsoft Provisioning IE to
advertise that legacy 802.1X is not supported.
This seems to make Windows ask for a static WEP key when adding a new
network, but at least Windows XP SP3 was still marking IEEE 802.1X
enabled for the network. Anyway, this is better than just leaving the
network configured with IEEE 802.1X and automatic WEP key distribution.
I tried PBC with the hostapd registrar.
I pushed the button with "hostap_cli WPS_PBC".
But hostapd registrar always sends Selected Registrar Config Methods
attribute=0x0000 in beacon/probe response.
Allow more than one pending PutWLANMessage data to be stored (M2/M2D
from multiple external Registrars) and drop pending M2/M2D messages when
the Enrollee replies with M3.
It looks like we don't set correspondent Device Password ID attribute in
M2 message during PBC registration. Without it TG185n STA was not able
to connect to our AP in PBC mode. Attached patch fixes this.
This adds mostly feature complete external Registrar support with the
main missing part being proper support for multiple external Registrars
working at the same time and processing of concurrent registrations when
using an external Registrar.
This code is based on Sony/Saice implementation
(https://www.saice-wpsnfc.bz/) and the changes made by Ted Merrill
(Atheros) to make it more suitable for hostapd design and embedded
systems. Some of the UPnP code is based on Intel's libupnp. Copyrights
and licensing are explained in src/wps/wps_upnp.c in more detail.
If a Registrar tries to configure the AP, but fails to validate the
device password (AP PIN), lock the AP setup after four failures. This
protects the AP PIN against brute force guessing attacks.
This operation can now be moved into an external program by configuring
hostapd with wps_cred_processing=1 and skip_cred_build=1. A new
ctrl_iface message (WPS-REG-SUCCESS <Enrollee MAC addr> <UUID-E>) will
be used to notify external programs of each successful registration and
that can be used as a tricker to move from unconfigured to configured
state.
This callback is now used to stop wpa_supplicant from trying to continue
using parameters (most likely, device password) that do not work in a
loop. In addition, wpa_gui can now notify user of failed registration.
Instead of sending out EAP-Failure on errors (on AP) or stopping (on
Supplicant), send a NACK message based on the allowed EAP state machine
transitions for EAP-WSC.
Since the Registrar may not yet know the UUID-E when a new PIN is
entered, use of a wildcard PIN that works with any UUID-E can be useful.
Such a PIN will be bound to the first Enrollee trying to use it and it
will be invalidated after the first use.
Fragment WPS IE if needed to fit into the IE length limits in hostapd
and Reassemble WPS IE data from multiple IEs in wpa_supplicant.
In addition, moved WPS code from events.c into wps_supplicant.c to clean
up module interfaces.
Previously, wpa_supplicant as Enrollee case was handled using a
different callback function pointer. However, now that the wps_context
structure is allocated for all cases, the same variable can be used in
all cases.
This allows the network to be used after the Registrar configuration
step. The local WPS network is replaced with a new network block
similarly to the case of acting as an Enrollee.
