This is not really of that much use since rc4_skip() can be used as
easily. In addition, rc4 has caused some symbol conflicts in the past,
so it is easier to live without that as an exported symbol.
Do not initialize EAPOL state machine for the STA when hostapd is
configured to use WPS with open or shared WEP networks. This allows the
STA to use EAPOL-Start to indicate it wants to start WPS in such a case
and hostapd does not end up running through EAPOL authentication timeout
and disconnecting the STA if WPS is not used.
There was already code for starting EAPOL state machines based on
received EAPOL packets, but that was not working properly since
portEnabled was not set to TRUE on that code path. This is now fixed,
too.
driver.h contains the definitions needed in driver wrapper
implementations (driver_*.c) and driver_i.h contains the definitions
that are used in core hostapd code to interact with the driver wrappers.
There is not really much else the Authenticator can do if it does not
receive valid EAP response from the Supplicant/EAP peer. EAP-Failure
would need to be sent before trying to start again with
EAP-Request/Identity, but that is not allowed before the EAP peer
actually replies. Anyway, forcing a new association is likely to clean
up peer state, too, so it can help fixing some issues that could have
caused the peer not to be able to reply in the first place.
It looks like this never survived the move from IEEE 802.1X-2001 to
IEEE 802.1X-2004 and EAP state machine (RFC 4137). The retransmission
scheduling and control is now in EAP authenticator and the
calculateTimeout() producedure is used to determine timeout for
retransmission (either dynamic backoff or value from EAP method hint).
The recommended calculations based on SRTT and RTTVAR (RFC 2988) are not
yet implemented since there is no round-trip time measurement available
yet.
This should make EAP authentication much more robust in environments
where initial packets are lost for any reason. If the EAP method does
not provide a hint on timeout, default schedule of 3, 6, 12, 20, 20, 20,
... seconds will be used.
If a STA reassociates and changes key_mgmt (e.g., from WPA-PSK to WPS),
hostapd needs to reset some of the existing STA and WPA state machine
variables to allow correct processing for the new association.
This adds WPS support for both hostapd and wpa_supplicant. Both programs
can be configured to act as WPS Enrollee and Registrar. Both PBC and PIN
methods are supported.
Currently, hostapd has more complete configuration option for WPS
parameters and wpa_supplicant configuration style will likely change in
the future. External Registrars are not yet supported in hostapd or
wpa_supplicant. While wpa_supplicant has initial support for acting as
an Registrar to configure an AP, this is still using number of hardcoded
parameters which will need to be made configurable for proper operation.
Changed accounting_sta_start() to call accounting_sta_get_id()
internally in accounting.c so that external callers do not need to do
anything to allocate unique accounting id. When starting a new session,
a unique identifier is needed anyway, so no need to keep these
operations separate.
Changed EAP-FAST configuration to use separate fields for A-ID and
A-ID-Info (eap_fast_a_id_info) to allow A-ID to be set to a fixed
16-octet len binary value for better interoperability with some peer
implementations; eap_fast_a_id is now configured as a hex string.
eap_fast_prov config parameter can now be used to enable/disable different
EAP-FAST provisioning modes:
0 = provisioning disabled
1 = only anonymous provisioning allowed
2 = only authenticated provisioning allowed
3 = both provisioning modes allowed
IEEE 802.11w/D6.0 defines new AKMPs to indicate SHA256-based algorithms for
key derivation (and AES-CMAC for EAPOL-Key MIC). Add support for using new
AKMPs and clean up AKMP processing with helper functions in defs.h.
