Commit graph

3042 commits

Author SHA1 Message Date
Jouni Malinen
568475b70b HS 2.0: Allow CANCEL_FETCH_OSU to stop at scan completion
There is no need to start the GAS/ANQP fetch if the FETCH_OSU operation
has already been canceled.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-14 02:28:03 +02:00
Jouni Malinen
f77cedc11a WPS ER: Remove unnecessary return value
wps_er_deinit() cannot fail and it does not return anything, so neither
should wpas_wps_er_stop().

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-14 02:28:03 +02:00
Jouni Malinen
5407c69d15 Remove unnecessary STA_AUTOCONNECT handler function
This function could not fail and it can be replaced with a single
line variable update that takes less code than the function call.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-13 19:27:41 +02:00
Jouni Malinen
a1144000cd Remove unnecessary return value
wpa_bss_flush*() cannot fail and as such, there is no need for
wpa_supplicant_ctrl_iface_bss_flush() to return a value either.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-13 19:22:23 +02:00
Jouni Malinen
5ac73acf12 Simplify eapol_sm_get_mib() result handling
This function cannot return negative value, so no need to check for
that. If there is not enough room in the buffer or if something
unexpected happens, 0 is returned.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-13 19:15:38 +02:00
Jouni Malinen
43a66ecba3 Fix SCAN control interface command error cases
Update the scan parameters in wpa_s only in case the scan command is
going to be executed. In other words, do not change the parameters for
an ongoing scan (the SCAN command is rejected with FAIL-BUSY) or if any
of the parameters is invalid.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-12 01:12:15 +02:00
Jouni Malinen
2961bfa8e1 Remove unused send_eapol() driver op
The send_eapol() callback was used by driver_test.c, but with that
removed, there is no remaining users of the alternative EAPOL frame
transmitting mechanism in wpa_supplicant, i.e., all remaining driver
interfaces use l2_packet instead. Remove the send_eapol() to get rid of
unused code.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-11 15:40:07 +02:00
Jouni Malinen
b68d602dc4 Fix ANQP_GET/HS20_GET_ANQP parsing to skip space after address
The space following the BSSID was not skipped properly if the following
parameter started with the "hs20:" prefix. For other cases, atoi() ended
up ignoring the space, but it is cleaner to skip it anyway for all
cases.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-11 15:18:11 +02:00
Jouni Malinen
42a697256e P2P: Allow cross connection on the parent interface
Previously, any P2P capable interface was skipped in cross connection
uplink consideration. However, this ends up skipping more or less all
nl80211-based driver cases now since they mark the main interface P2P
capable. Relax this rule to allow the parent interface to be used as the
non-P2P station interface for cross connection purposes.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-10 01:54:27 +02:00
Jouni Malinen
97cfe110dc Clear wpa_s->disconnected on ctrl_iface FLUSH
This is needed to get into more consistent state after the FLUSH
command. DISCONNECT followed by FLUSH could result in
wpa_s->disconnected being left to 1 and this resulted in a test failure,
e.g., when running wpas_ctrl_dup_network followed by
wpas_ctrl_enable_disable_network where the latter was expecting
ENABLE_NETWORK on a disabled network to connect automatically and that
does not happen if wpa_s->disconnected == 1.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-08 16:22:13 +02:00
Jouni Malinen
aaadd72733 Check os_snprintf() result more consistently - more checks
Add more os_snprintf() result validation checks.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
1d39977136 Check os_snprintf() result more consistently
While these are using practically large enoungh buffer sizes, it is
better to be more consistent with checking os_snprintf() return value.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
1f102d3bb0 Check os_snprintf() result more consistently - manual
This converts os_snprintf() result validation cases to use
os_snprintf_error() for cases that were note covered by spatch and
semantic patches.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
eeab4f2fda Check os_snprintf() result more consistently - automatic 3
This converts os_snprintf() result validation cases to use
os_snprintf_error() where the comparison was 'res > size' instead of
'res >= size - 1'. These changes were done automatically with spatch
using the following semantic patch:

@@
identifier E1;
expression E2,E3,E4,E5,E6;
statement S1;
@@

(
  E1 = os_snprintf(E2, E3, ...);
|
  int E1 = os_snprintf(E2, E3, ...);
|
  if (E5)
	E1 = os_snprintf(E2, E3, ...);
  else
	E1 = os_snprintf(E2, E3, ...);
|
  if (E5)
	E1 = os_snprintf(E2, E3, ...);
  else if (E6)
	E1 = os_snprintf(E2, E3, ...);
  else
	E1 = 0;
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	return -1;
  }
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else if (E6) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	return -1;
  }
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	E1 = os_snprintf(E2, E3, ...);
  }
)
? os_free(E4);
- if (E1 < 0 || (size_t) E1 >= E3 - 1)
+ if (os_snprintf_error(E3, E1))
(
  S1
|
{ ... }
)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
7bdd8981f7 Check os_snprintf() result more consistently - automatic 2
This converts os_snprintf() result validation cases to use
os_snprintf_error() where the comparison was 'res > size' instead of
'res >= size'. These changes were done automatically with spatch using
the following semantic patch:

@@
identifier E1;
expression E2,E3,E4,E5,E6;
statement S1;
@@

(
  E1 = os_snprintf(E2, E3, ...);
|
  int E1 = os_snprintf(E2, E3, ...);
|
  if (E5)
	E1 = os_snprintf(E2, E3, ...);
  else
	E1 = os_snprintf(E2, E3, ...);
|
  if (E5)
	E1 = os_snprintf(E2, E3, ...);
  else if (E6)
	E1 = os_snprintf(E2, E3, ...);
  else
	E1 = 0;
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	return -1;
  }
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else if (E6) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	return -1;
  }
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	E1 = os_snprintf(E2, E3, ...);
  }
)
? os_free(E4);
- if (E1 < 0 || \( E1 > E3 \| (size_t) E1 > E3 \| E1 > (int) E3 \))
+ if (os_snprintf_error(E3, E1))
(
  S1
|
{ ... }
)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
d85e1fc8a5 Check os_snprintf() result more consistently - automatic 1
This converts os_snprintf() result validation cases to use
os_snprintf_error() where the exact rule used in os_snprintf_error() was
used. These changes were done automatically with spatch using the
following semantic patch:

@@
identifier E1;
expression E2,E3,E4,E5,E6;
statement S1;
@@

(
  E1 = os_snprintf(E2, E3, ...);
|
  int E1 = os_snprintf(E2, E3, ...);
|
  if (E5)
	E1 = os_snprintf(E2, E3, ...);
  else
	E1 = os_snprintf(E2, E3, ...);
|
  if (E5)
	E1 = os_snprintf(E2, E3, ...);
  else if (E6)
	E1 = os_snprintf(E2, E3, ...);
  else
	E1 = 0;
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	return -1;
  }
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else if (E6) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	return -1;
  }
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	E1 = os_snprintf(E2, E3, ...);
  }
)
? os_free(E4);
- if (E1 < 0 || \( E1 >= E3 \| (size_t) E1 >= E3 \| (unsigned int) E1 >= E3 \| E1 >= (int) E3 \))
+ if (os_snprintf_error(E3, E1))
(
  S1
|
{ ... }
)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
a80ba67a26 Check os_snprintf() result more consistently - success case
This converts os_snprintf() result validation cases to use
os_snprintf_error() in cases where success condition was used to execute
a step. These changes were done automatically with spatch using the
following semantic patch:

@@
expression E1,E2,E3;
statement S1;
@@

  E1 = os_snprintf(E2, E3, ...);
- if (\( E1 >= 0 \| E1 > 0 \) && \( (size_t) E1 < E3 \| E1 < (int) E3 \| E1 < E3 \))
+ if (!os_snprintf_error(E3, E1))
  S1

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
a9aaacbb50 Check os_snprintf() result more consistently - maximum length
This adds verification of os_snprintf() result against the maximum
buffer length. These changes were done automatically with spatch
using the following semantic patch:

@@
expression E1,E2,E3;
statement S1;
@@

  E1 = os_snprintf(E2, E3, ...);
- if (\( E1 < 0 \| E1 <= 0 \))
+ if (os_snprintf_error(E3, E1))
(
  S1
|
{ ... }
)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
faebdeaa9e Use os_calloc() instead of os_zalloc()
Automatic changes with spatch using the following semantic patch:

@@
constant C;
type T;
@@

- os_zalloc(C*sizeof(T))
+ os_calloc(C,sizeof(T))

@@
expression E;
type T;
@@

- os_zalloc((E)*sizeof(T))
+ os_calloc(E,sizeof(T))

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
c054190603 Fix DUP_NETWORK debug print on error case
Incorrect network id was printed in debug output if DUP_NETWORK
destination network was not found.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
49328f0756 Remove unnecessary ctrl_iface command check
MESH_GROUP_REMOVE always passes in the cmd pointer, so this cannot
really be NULL.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:06 +02:00
Jouni Malinen
d02dcb28bc Remove unnecessary ctrl_iface cmd check
This pointer cannot be NULL sicne it is called only from this file and
with a valid pointer to the received command.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:07:56 +02:00
Jouni Malinen
d84416a2af Interworking: Make bounds checking easier for static analyzers
'num * 5 > end - pos' handles bounds checking a bit more efficiently,
but apparently that is not clear enough for all static analyzers.
Replace with 'num > left / 5' to avoid false reports. (CID 68117)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-06 19:25:14 +02:00
Jouni Malinen
8105821b39 Replace send_ft_action() driver_op with send_action()
This reduced number of unnecessarily duplicated driver interface
callback functions for sending Action frames by using the more generic
send_action() instead of FT specific send_ft_action().

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-06 18:13:29 +02:00
Jouni Malinen
bc0ba01d70 WFD: Allow WFD_SUBELEM_SET/GET all to be used with full IE buffer
This extends the previously used WFD_SUBELEM_SET/GET <subelem id> design
to allow special "all" value to be used as an id to indicate that all
WFD subelements are to be set/get. This uses similar interface as was
previously added over D-Bus.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-05 15:22:33 +02:00
Jouni Malinen
f80936094e WMM-AC: Use DEBUG verbosity for ignoring Action frame messages
There is no point in flooding the log with WARNING or ERROR level
messages if WMM-AC related Action frames are ignored in cases where they
were not expected. In addition, WARNING/ERROR should not really be used
in cases an invalid frame is dropped especially if this is not related
to a security setup since external devices could otherwise generate log
entries.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-05 13:17:57 +02:00
Jouni Malinen
0570a3ea7d HS 2.0: Clarify OSU Provider list length validation
The previous version was somewhat too complex for some static analyzers.
Use local variables for the extracted length fields and explicitly
compare these against the remaining buffer length. (CID 68121)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-05 00:56:05 +02:00
Jouni Malinen
65d9a5e254 ERP: Add wpa_supplicant ERP_FLUSH ctrl_iface command
This can be used to flush all the ERP keys.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-04 12:16:29 +02:00
Jouni Malinen
02a8d45ace ERP: Add support for ERP on EAP peer
Derive rRK and rIK on EAP peer if ERP is enabled. The new wpa_supplicant
network configuration parameter erp=1 can now be used to configure the
EAP peer to derive EMSK, rRK, and rIK at the successful completion of an
EAP authentication method. This functionality is not included in the
default build and can be enabled with CONFIG_ERP=y.

If EAP authenticator indicates support for re-authentication protocol,
initiate this with EAP-Initiate/Re-auth and complete protocol when
receiving EAP-Finish/Re-auth.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-04 12:16:29 +02:00
Dmitry Shmidt
f34891a3af Return only full network line in list_networks
It makes more sense to truncate at line boundary especially with the new
LAST_ID parameter.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-12-03 22:31:53 +02:00
Vinit Deshpande
90903a77ef List all networks despite message limit of 4096 bytes
This change creates 'LIST_NETWORK LAST_ID=x' form to allow
retrieval of all networks saved in the system. Without this form,
only first few (whatever fills in first 4096 bytes) can be
retrieved.

Signed-off-by: Vinit Deshpande <vinitd@google.com>
2014-12-02 23:47:27 +02:00
Jouni Malinen
44177b69e8 Allow a BSS entry with all-zeros BSSID to expire
wpa_bss_in_use() used to determine that a BSS with BSSID of
00:00:00:00:00:00 is in use in almost every case since either
wpa_s->bssid or wpa_s->pending_bssid was likely to be cleared. This
could result in a corner case of a BSS entry remaining in the BSS table
indefinitely if one was added there with a (likely bogus) address of
00:00:00:00:00:00. Fix this by ignore wpa_s->bssid and
wpa_s->pending_bssid if the BSSID in the BSS table entry is
00:00:00:00:00:00.

In theory, that address is a valid BSSID, but it is unlikely to be used
in any production AP, so the potential expiration of a BSS entry with
that address during a connection attempt would not be a concern
(especially when a new scan would be enough to recover from that).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-02 19:46:58 +02:00
Jouni Malinen
e374522827 Do not start new radio work on scan completion during ext work
Externally triggered scan could result in a new radio work item getting
started even when external radio work was in progress. Delay such start
until the external work is completed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-01 20:17:08 +02:00
Jouni Malinen
4f9a5ea5cc WPS: Fix current_ssid clearing on duplicate network removal
It was possible for the current network profile to be deleted when
merging duplicated WPS credentials. However, this did not clear
wpa_s->current_ssid and it was possible for something else to end up
dereferencing that pointer to now freed memory. This could be hit, e.g.,
with ap_wps_mixed_cred. Fix this by clearing current_ssid also in this
code path similarly to other cases of network block getting removed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-30 15:53:11 +02:00
Jouni Malinen
e4a35f07d9 mesh: Skip fast-association when using connect_without_scan
The mesh group addition was designed to use wpa_s->connect_without_scan
to skip a scan. That path was skipped if wpa_supplicant_fast_associate()
allowed previous scan results to be used. This could result in undesired
double-initialization attempt for the mesh interface. Avoid this by not
using wpa_supplicant_fast_associate() when wpa_s->connect_without_scan
is set.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-30 15:53:11 +02:00
Jouni Malinen
608b0ff52a mesh: Check for initialization failures
It is possible that these location ended up getting called before mesh
startup operations had been completed and that could result in
dereferencing NULL pointers. Address those error cases by verifying that
the needed parameters are available before using them.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-30 15:53:11 +02:00
Jouni Malinen
9a700ff9ef Ignore auth/assoc timeout events in mesh configuration
It was possible for auth/assoc timeout/failure event from the driver to
result in unexpected processing during mesh group setup if that
operation was started before the previously started driver operation to
association/connect had completed. Since those events cannot happen in
mesh cases, ignore them to avoid issues due to this corner case.

For example, monitor_iface_unknown_sta followed by wpas_mesh_secure test
case resulted in failure without this change.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-30 15:53:11 +02:00
Jouni Malinen
763041b2e8 mesh: Avoid a false maybe-uninitialized compiler warning
An earlier check of the action_field value above the switch statement
already took care of all other possible cases, but that was apparently
too difficult for the compiler to notice. Bring back the default case to
avoid incorrect warnings about the event variable being maybe
uninitialized.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-30 15:53:11 +02:00
Jouni Malinen
c932b43e56 mesh: Add more debug information to MPM Action frame processing
This makes it easier to figure out why a peering message is dropped.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-28 23:02:29 +02:00
Jouni Malinen
fc0ef7c0e7 Add DATA_TEST_FRAME for testing Data frame processing
The new wpa_supplicant control interface command can be used in
automated testing to verify how AP processes Data frames with arbitrary
contents. This is enabled only in builds with CONFIG_TESTING_OPTIONS=y.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 23:51:46 +02:00
Jouni Malinen
b925506a91 Clear RSN preauth and PMKSA cache state on FLUSH command
There is no need for this state to maintained when the wpa_supplicant
FLUSH ctrl_iface command is used to request flushing of all state.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 19:56:15 +02:00
Jouni Malinen
3882a70841 WMM AC: Fix memory leak on deinit without disassoc event
It was possible for wmm_ac_deinit() not getting called when an interface
was removed in a sequence where disassociation was not reported and
wmm_ac_notify_disassoc() did not get called. This resulted in leaking
whatever memory was allocated for WMM AC parameters. Fix that by calling
wmm_ac_notify_disassoc() from wpa_supplicant_cleanup().

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 19:00:02 +02:00
Jouni Malinen
5214f4fafc Clear scan_req to NORMAL_SCAN_REQ for connection attempt
This is needed to fix some sequencies where a real scan in ap_scan=2
case would be issued even when the connection case would expect direct
connection without a scan.

This fixed an issue shown in hwsim test case autoscan_exponential
followed by ibss_open_fixed_bssid.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 17:55:54 +02:00
Jouni Malinen
4e0990dc88 mesh: Send peering close message before leaving mesh
This is needed to allow proper Action frame transmission to work without
having to claim these to be offchannel operations.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 17:12:47 +02:00
Neelansh Mittal
3a7414b6a6 Do not re-open Android control sockets
On Android, the control socket being used may be the socket that is
created when wpa_supplicant is started as a /init.*.rc service. Such a
socket is maintained as a key-value pair in Android's environment.
Closing this control socket would leave wpa_supplicant in a bad state.
When wpa_supplicant re-opens the ctrl_iface socket, it will query the
Android's environment, and will be returned with the same socket
descriptor that has already been closed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-25 17:16:44 +02:00
Masashi Honma
a959a3b69d SAE: Fix Anti-Clogging Token request frame format
This commit inserts Finite Cyclic Group to Anti-Clogging Token request
frame because IEEE Std 802.11-2012, Table 8-29 says "Finite Cyclic Group
is present if Status is zero or 76".

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-11-25 16:08:53 +02:00
Jouni Malinen
849367afe9 SME: Fix a sign-compare warning
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-25 01:07:16 +02:00
Jouni Malinen
158211b2db WNM: Use country code, if available, to help in channel mapping
The country code from the current AP needs to be used in
ieee80211_chan_to_freq() to support cases where non-global operating
class table is used.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-24 10:57:38 +02:00
Jouni Malinen
5d017065a0 GAS: Clean up Query Response length validation
Previous version was correct, but apparently too complex for some static
analyzers. (CID 68119)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-23 21:03:40 +02:00
Jouni Malinen
355e17eb1b HS 2.0: Clarify OSU Server URI length validation
The previous version was valid, but apparently too complex for some
static analyzers. Use a local variable for uri_len and explicitly
compare it against the remaining buffer length. (CID 68121)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-23 21:03:40 +02:00