This will need some additional code in wps_er_pbc() to handle PBC mode
enabling for a single AP only. For now, this can only be expected to work
when the ER is connected to a single AP.
UPnP device architecture specification requires all evented variables to
be included in the initial event message after subscription. Since this
can happen before we have seen any events, generated a dummy event
(WSC_ACK with all-zeros nonces) if needed.
This will notify control points of the services going away and allows
them to notice this without having to wait timeout on the
initial advertisements.
This removes following WFA WLANConfig Service actions and the related
state variables: GetAPSettings, SetAPSettings, DelAPSettings,
GetSTASettings, SetSTASettings, DelSTASettings, RebootAP,
ResetAP, RebootSTA, ResetSTA.
While WFA WLANConfig Service version 1.0 claims that some of these are
mandatory to implement for an AP, there are no known implementations
supporting these actions neither in an AP/proxy or an External Registrar
that would use them. These are unlikely to be supported in the future
either and as such, it is just simpler to get rid of them to clean up
the implementation and reduce code size.
When using UPnP transport, the Op-Code is not included, but the WPS
frame processing will need this. Generate a matching Op-Code based
on the message type.
Previously, WSC_MSG was hardcoded for every message from ER, but
this needs to be changed based on message type to send a valid
message to the Enrollee via EAP transport.
New PINs can now be added to WPS ER. This results in the ER code
using SetSelectedRegistrar to modify AP state so that Enrollees
will be able to notice the actice registrar more easily.
This keeps STA/Enrollee entries up to date and sets up registration
protocol session. M1 is processed and M2D generated, but the there
is no code yet to transmit the response back to the AP with
PutWLANResponse.
Always bring down the wlan interface, even when not changing the
BSSID, the interface also needs to be down for changing its type
from managed to AP mode.
The receive Probe Request and EAP-WSC notifications are now parsed
(including the TLVs in them) and contents is shown in the debug log.
Actual processing of the received information is still missing (TODO
comments indicate the needed functionality).
rand would be the address of rand() function and never NULL. The previous
version could have crashed on invalid AKA-AUTS command. Though, these
commands are only from hostapd which sends valid requests and as such,
the actual issue did not show up.
This is like wpa_msg(), but the output is directed only to
ctrl_interface listeners. In other words, the output will not be
shown on stdout or in syslog.
Change scan result reporting to use wpa_msg_ctrl() for
CTRL-EVENT-SCAN-RESULTS message at info level and wpa_printf() at
debug level to avoid showing scan result events in syslog in the
common configuration used with NetworkManager.
This adds code to start a HTTP server and to subscribe to UPnP events
from each discovered WPS AP. The event messages are received, but there
is not yet any code to actually parse the contents of the event.
Clean up code so that UPnP implementation does not need to include all
the HTTP functionality. In addition, make it easier to share HTTP server
functionality with other components in the future.
Instead of implementing HTTP client functionality inside
wps_upnp_event.c, use a generic HTTP client module to do this. The HTTP
client code can now be shared more easily for other purposes, too.
This is the first step in adding support for using wpa_supplicant as a
WPS External Registrar to manage APs over UPnP. Only the device
discovery part is implemented in this commit.
While the actual use here would be unlikely to be broken by any C
optimization, it is better to use explicit union construction to let
gcc know about the aliasing and avoid warnings from gcc 4.4.
gcc 4.4 ends up generating strict-aliasing warnings about some very common
networking socket uses that do not really result in a real problem and
cannot be easily avoided with union-based type-punning due to struct
definitions including another struct in system header files. To avoid having
to fully disable strict-aliasing warnings, provide a mechanism to hide the
typecast from aliasing for now. A cleaner solution will hopefully be found
in the future to handle these cases.
Though we have such a timeout when handling SetSelectedRegistrar UPnP
message from an external registrar, it looks like we don't have one when
the internal registrar is activated for PIN connection. Thus we set the
SelectedRegistrar flag when AP is activated for PIN connection but we
never reset it - not by some timeout, nor when registration succeeds.
This lead to situations where AP everlastingly declare that it is
activated for WPS PIN connection when in reality it is not.
Use the same timeout (and also success with PIN) to clear the selected
registrar flag when using internal registrar, too.
If PBC session overlap is detected during an ongoing PBC protocol run,
reject the run (if M8, i.e., credentials, have not yet been sent). This
provides a bit longer monitoring time at the Registrar for PBC mode to
catch some cases where two Enrollees in PBC mode try to enroll
credentials at about the same time.
This provides information about PBC mode result from the WPS Registrar
module. This could be used, e.g., to provide a user notification on the
AP UI on PBC failures.
If PBC session overlap is detected between button press on the registrar
and M1 is reception, report session overlap with the Config Error
attribute in M2D to the Enrollee.
This functionality fits better with src/tls (i.e., internal TLS
implementation), so move it there to make crypto_internal.c more
of a wrapper like other crypto_*.c files.
Private keys can now be used in either unencrypted or encrypted
PKCS #8 encoding. Only the pbeWithMD5AndDES-CBC algorithm (PKCS #5)
is currently supported.
Recognize the PEM header "BEGIN PRIVATE KEY" as base64-decode the data
to be able to use PEM encoded, unencrypted PKCS#8 private keys with the
internal TLS implementation. Previously, only DER encoding of the
PKCS#8 private key was supported.
OpenSSL 0.9.7 does not include get_rfc3526_prime_1536() function, so
provide that functionality internally if needed. In addition, make
sha256_vector() building depend on whether SHA256 support is included
in the OpenSSL library. This with CONFIG_INTERNAL_SHA256=y in .config
allows OpenSSL without SHA256 support to be used.
Both hostapd/wpa_supplicant compilation fails on DragonFly BSD.
This patch solves this issue.
I have tested only compilation. Not functionality.
Because I don't have any device which can work on DragonFly BSD.
mac80211 does not currently allow (re)authentication when we are already
authenticated. In order to work around this, force deauthentication if
nl80211 authentication command fails with EALREADY. Unfortunately, the
workaround code in driver_nl80211.c alone is not enough since the
following disconnection event would clear wpa_supplicant authentication
state. To handle this, add some code to restore authentication state
when using userspace SME.
This workaround will hopefully become unnecessary in some point should
mac80211 start accepting new authentication requests even when in
authenticated state.
Reorganize the TLS/crypto library segments into a single set of blocks
for each library instead of multiple locations handling library-specific
operations. Group crypto functionality together and get wpa_supplicant
and hostapd Makefile closer to eachother in order to make it easier to
eventually move this into a shared makefile.
Crypto library wrappers can now override the internal DH (group 5)
implementation. As a starting point, this is done with OpenSSL. The
new mechanism is currently available only for WPS (i.e., IKEv2 still
depends on the internal DH implementation).
Replace "nl80211: Ignored unknown event (cmd=33)" with
"nl80211: Scan trigger" to make debug output clearer. We do not
currently do anything with this event apart from showing it in
the debug log.
This allows NSS to be used to derive EAP-TLS/PEAP/TTLS keying material.
NSS requires a patch from
https://bugzilla.mozilla.org/show_bug.cgi?id=507359
to provide the new API. In addition, that patch needs to be modified to
add the 16-bit context length value in SSL_ExportKeyingMaterial() only if
contextlen != 0 in order to match with the EAP-TLS/PEAP/TTLS use cases.
This issue seems to be coming from the unfortunate incompatibility in
draft-ietf-tls-extractor-07.txt (draft-ietf-tls-extractor-00.txt would
have used compatible PRF construction).
At this point, it is unclear how this will be resolved eventually, but
anyway, this shows a mechanism that can be used to implement EAP key
derivation with NSS with a small patch to NSS.
This brings in the first step in adding support for using NSS
(Mozilla Network Security Services) as the crypto and TLS library
with wpa_supplicant. This version is able to run through EAP-PEAP
and EAP-TTLS authentication, but does not yet implement any
certificate/private key configuration. In addition, this does not
implement proper key fetching functions either, so the end result
is not really of much use in real world yet.
On DragonFly BSD, wired IEEE 802.1X fails with this message:
ioctl[SIOC{ADD/DEL}MULTI]: Invalid argument
This patch solves this issue.
I have tested with these:
OS : DragonFly BSD 2.4.0
EAP : EAP-TLS
Switch : Cisco Catalyst 2950
This reverts commit 5aa9cb5cca.
The nested key attribute is using different attribute values
(NL80211_KEY_* vs. NL80211_ATTR_KEY_*), so cannot share the same routine
for these purposes..
Current wpa_supplicant has a bug with WEP keys, it adds a zero-length
sequence counter field to netlink which the kernel doesn't accept.
Additionally, the kernel API slightly changed to accept keys only when
connected, so we need to send it the keys after that. For that to work
with shared key authentication, we also include the default WEP TX key
in the authentication command.
To upload the keys properly _after_ associating, add a new flag
WPA_DRIVER_FLAGS_SET_KEYS_AFTER_ASSOC_DONE indicating that the driver
needs the keys at that point and not earlier.
Commit 0b55b934ee broke this by not
initializing drv->ap = 1 in hostapd case since the mode updating
code ended up unlinking the socket file. Setting drv->ap = 1
removes the mode change and as such, unlinking of the socket file.
It is simpler to just build in all the test driver code regardless
of whether this is for hostapd or wpa_supplicant (which will eventually
get AP mode support with driver_test, too).
radius_server_encapsulate_eap() resets sess->eap->if->eap{Success,Fail}
to FALSE, such that the completion condition is never true.
The net effect is that completed sessions would linger for
RADIUS_SESSION_TIMEOUT seconds.
Signed-off-by: Alex Badea <vamposdecampos@gmail.com>
Previously, the default settings allowed 100 sessions in 60 seconds.
With this fix, the default limit is now 100 sessions per 10 seconds.
[Bug 329]
Store a copy of device attributes during WPS protocol run and make it
available for external programs via the control interface STA MIB
command for associated stations. This gives access to device name and
type which can be useful when showing user information about associated
stations.
wpa_supplicant can now reconfigure the AP by acting as an External
Registrar with the wps_reg command. Previously, this was only used
to fetch the current AP settings, but now the wps_reg command has
optional arguments which can be used to provide the new AP
configuration. When the new parameters are set, the WPS protocol run
is allowed to continue through M8 to reconfigure the AP instead of
stopping at M7.
This is an initial step in adding support for the new connect command.
For now, we just add the capability query. The actual use of the new
command will be added separately.
This is a patch for OpenBSD wired IEEE 802.1X. This is only for wired,
not wireless, because OpenBSD uses wpa_supplicant only on wired now.
http://www.openbsd.org/cgi-bin/cvsweb/ports/security/wpa_supplicant/
I have tested with these.
OS : OpenBSD 4.5
EAP : EAP-TLS
Switch : CentreCOM 8724SL
Previously, both the command replies and unsolicited events were
received from the same socket. This could cause problems if an event
message is received between a command and the response to that command.
Using two sockets avoids this issue.
When Linux has Path MTU discovery enabled, it sets by default the DF bit
on all outgoing datagrams, also UDP ones. If a RADIUS message is bigger
than the smallest MTU size to the target, it will be discarded.
This effectively limits RADIUS messages to ~ 1500 Bytes, while they can
be up to 4k according to RFC2865. In practice, this can mean trouble
when doing EAP-TLS with many RADIUS attributes besides the EAP-Message.
[Bug 326]
When Linux has Path MTU discovery enabled, it sets by default the DF bit
on all outgoing datagrams, also UDP ones. If a RADIUS message is bigger
than the smallest MTU size to the target, it will be discarded.
This effectively limits RADIUS messages to ~ 1500 Bytes, while they can
be up to 4k according to RFC2865. In practice, this can mean trouble
when doing EAP-TLS with many RADIUS attributes besides the EAP-Message.
[Bug 326]
These could, at least in theory, be used to generate unexpected common
name or subject alternative name matches should a CA sign strings with
NUL (C string termination) in them. For now, just reject the certificate
if an embedded NUL is detected. In theory, all the comparison routines
could be made to compare these strings as binary blobs (with additional
X.509 rules to handle some exceptions) and display NUL characters
somehow. Anyway, just rejecting the certificate will get rid of
potential problems with the C string getting terminated and it should
not really be used in certificates, so this should not break valid use
cases.
The BLOCK_SIZE define can be made more specific by using AES_ prefix and
by moving it to aes.h. After this, most aes-*.c do not really need to
include anything from the internal aes_i.h header file. In other words,
aes_i.h can now be used only for the code that uses the internal AES
block operation implementation and none of the code that can use AES
implementation from an external library do not need to include this
header file.
Better not specify EVP_CIPHER again for the second init call since that
will override key length with the default value. The previous version
was likely to work since most use cases would be likely to use the
default key length. Anyway, better make this handle variable length
ciphers (mainly, RC4), too, just in case it is needed in the future.
This is not really of that much use since rc4_skip() can be used as
easily. In addition, rc4 has caused some symbol conflicts in the past,
so it is easier to live without that as an exported symbol.
wpa_supplicant can now be built with FIPS capable OpenSSL for FIPS mode
operation. Currently, this is only enabling the FIPS mode in OpenSSL
without providing any higher level enforcement in wpa_supplicant.
Consequently, invalid configuration will fail during the authentication
run. Proper configuration (e.g., WPA2-Enterprise with EAP-TLS) allows
the connection to be completed.
Instead of using low level, digest-specific functions, use the generic
EVP interface for digest functions. In addition, report OpenSSL errors
in more detail.
Some crypto libraries can return in these functions (e.g., if a specific
hash function is disabled), so we better provide the caller a chance to
check whether the call failed. The return values are not yet used
anywhere, but they will be needed for future changes.
On NetBSD 5.0, when I use wired 802.1X, "Invalid argument" occurs
on SIOCADDMULTI ioctl and 802.1X fails.
I tried FreeBSD code, but "Address family not supported by protocol family"
occurs on SIOCADDMULTI ioctl and 802.1X fails, too.
This patch solves this issue.
I have tested with these:
OS : NetBSD 5.0
EAP : EAP-MD5
Switch : CentreCOM 8724SL
This is a (hopefully) temporary workaround to allow the same source code
tree to be used for building hostapd and wpa_supplicant without having
to manually force recompilation of some files. Currently, some of the
driver wrapper files need to be built separately for hostapd and
wpa_supplicant (#ifdef's in the files based on AP functionality).
This is somewhat racy as far as parallel make execution is concerned,
i.e., it may be necessary to run "make -j#" twice (plain "make" works
fine. Since this is supposed to be a temporary workaround, there is not
much point in trying to fix this with any more complex make processing.
Instead of having all driver stuff collected across wpa_supplicant
and hostapd, create a common snippet that they both include and
that handles the build configuration.
If base64_encode() were to be used with a huge data array, the
previous version could have resulted in overwriting the allocated
buffer due to an integer overflow as pointed out in
http://www.freebsd.org/cgi/query-pr.cgi?pr=137484. However, there
are no know use cases in hostapd or wpa_supplicant that would do that.
Anyway, the recommended change looks reasonable and provides additional
protection should the base64_encode() function be used for something
else in the future.
Current wpa_supplicant has a bug with WEP keys, it adds a zero-length
sequence counter field to netlink which the kernel doesn't accept.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
hostapd currently tries to encrypt all auth frames,
except for "OPEN" and "SHARED with transaction 3".
This means that it will send an encrypted "unknown
auth algorithm" reply for all other algorithsm. Fix
this by changing the logic to only encrypt shared
key auth frames with transaction 3.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Change existing CONFIG_LIBNL20 compatibility code in
driver_nl80211.c to be used by both wpa_supplicant
and hostapd, but take care of nl_handle too now.
Propagate CONFIG_LIBNL20 out of .config file and onto
CFLAGS in the Makefile.
Use libnl-gen now too.
Signed-off-by: Jon Loeliger <jdl@bigfootnetworks.com>
---
This removes need for local configuration to ignore *.o and *~
and allows the src/*/.gitignore files to be removed (subdirectories
will inherit the rules from the root .gitignore).
This attribute is not supposed to be used in the response frame (i.e.,
it is only in the EAP-Request/SIM-Notification frame) per RFC 4186
chapters 10.1 and 9.9. This is a minor bug since the server is required
to ignore the contents of the EAP-Response/SIM-Notification during
protected result indication per chapter 6.2.
EAP-AKA peer was already following the similar specification in RFC 4187,
but this was somehow missed in the EAP-SIM peer implementation.
The driver wrappers should not need to include wps_hostapd.h, so let's
make this easier by introducing a driver callback for reporting Probe
Request frames.
Since we do not currently support changing the AP settings received
from M7, there is no point in actually sending out the M8 that would
likely trigger the AP to reconfigure itself and potentially reboot.
For now, we just receive the AP settings in M7 and add a local network
configuration block based on those, but NACK the message. This makes
wps_reg work like wps_pin, but by using the AP PIN instead of a client
PIN.
Old way does not work with all drivers on NetBSD and FreeBSD are
also using this so should be a safe change. [Bug 312]
Signed-off-by: Roy Marples <roy@marples.name>
Add generic functions to get/set 80211 vars, set 80211 params and
get/sid ssid.
Change NetBSD defines to match the ioctl used for portability.
Check size we're copying into instead of assuming IFNAMSIZ.
Signed-off-by: Roy Marples <roy@marples.name>
If hostapd segfaults, or is killed with -9, or the interface already exists,
when the interface is created, it will fail.
Configuration file: /tmp/hostapd/hostapd.conf
Failed to create interface mon.wlan0_0.
Using interface wlan0_0 with hwaddr 00:13:01:01:08:0a and ssid 'IG_0405_LAN'
Failed to set beacon head/tail or DTIM period
Failed to create interface wlan0_1.
Try to remove the interface and re-create it before aborting.
To ensure the supplicant starts and ends with a clean slate (keys are
already cleaned up at init and deinit time), force a null BSSID and
bogus SSID to ensure the driver isn't connected to anything.
Signed-off-by: Dan Williams <dcbw@redhat.com>
4853d5ac84 had a small bug in the order
of these function calls in _wext_deauthenticate() (_disassociate()
did have the correct order). The deauthentication frame is supposed
to go out (if driver supports that) before we disconnect more
forcefully.
Otherwise the driver might interpret the request as a request to
create/join a new adhoc network with the bogus SSID.
Signed-off-by: Dan Williams <dcbw@redhat.com>
hostapd_cli wps_pin command can now have an optional timeout
parameter that sets the PIN lifetime in seconds. This can be used
to reduce the likelihood of someone else using the PIN should an
active PIN be left in the Registrar.
The attached patch will replace get_scan_results with get_scan_results2.
This is a preparation for WPS on BSD.
And I erased "wpa_scan_result_compar". Because scan result
sorting will be done with "wpa_scan_result_compar" on
"scan_helpers.c".
I have done below tests on NetBSD with an atheros card.
- WPA2-PSK(CCMP)
- WPA-PSK(TKIP)
- PEAP(MSCHAPv2)
- EAP-TLS
- EAP-TTLS(MSCHAPv2)
This adds a cleaner mechanism for protecting against unauthorized
data frames than the previously used drop_unencrypted mechanism
(which is not even available with nl80211 and had to use a WEXT
ioctl.
The old drop_unencrypted code is left in for now as the final
surviving WEXT use in driver_nl80211.c. However, it can be removed
from the build by defining NO_WEXT. It may also be removed
eventually when most users are expected to be using recent enough
kernel version.
For now, the old code using NL80211_ATTR_STA_FLAGS is left in for
backwards compatibility with older kernel versions. It may be removed
eventually when most users are expected to be running with new
enough kernel version.
Some deployed implementations seem to advertise incorrect information
in this attribute. For example, Linksys WRT350N seems to have a
byteorder bug that breaks this negotiation. In order to interoperate
with existing implementations, assume that the Enrollee supports
everything we do.
Attached is a patch for the RoboSwitch driver in trunk. It is a
general revision of the source code.
Changes:
- Improved IEEE 802.1X conformance ([1])
- Better conformity to Broadcom specifications
- Fixed compatibility with different chipset revisions
It is worth noting that performance may drop a little using the new
driver. This can be overcome by using "multicast_only=1" as a
parameter. In that case only packets to the PAE group address are
regarded, as the previous revision of the driver did. A more detailed
description of the parameter and it's consequences is available at [2]
(summary: use "multicast_only=1" whenever possible).
[1] http://lists.shmoo.com/pipermail/hostap/2009-February/019398.html
[2] http://forum.openwrt.org/viewtopic.php?id=19873
None of the driver wrappers user this. hostapd-controlled broadcast SSID
hiding can only be used with drivers that use hostapd for handling
Beacon and Probe Request/Response frames.
None of the driver wrappers use this. Only the drivers that use hostapd
for Beacon and Probe Request/Response handling can now use IEEE 802.11d
properly.
Note: This changes values for existing NL80211_ATTR_MAX_SCAN_IE_LEN
and NL80211_ATTR_KEY_TYPE (for some reason, they ended up getting
swapped in wireless-testing.git) and as such, could break Michael
MIC error reporting (well, at least partially).
When in AP mode, wpa_supplicant is now enabling WPS (only Internal
Registrar). wpa_cli wps_pbc and wps_pin commands can be used to initiate
WPS negotiation similarly to how this is done in station mode (though,
the BSSID parameter is ignored).
There is no point in trying to continue if a 4-way handshake frame is
discarded or if PTK/GTK/IGTK configuration fails. Force the client to
disconnect in such a case to avoid confusing user by claiming the
connection was successfully completed.
These driver wrappers use UNIX domain sockets and as such, won't be
built with Microsoft compiler. Consequently, use of C99-style designated
initializers can be used to make these files easier to maintain. Only
driver_ndis.c needs to support the old C89-style due to Microsoft
compiler not supporting newer C standard.
This was not really supported by any of the included driver wrappers. If
this functionality is desired in the future, this (or something similar)
can be added with the changes needed into a driver wrapper to use the
mechanism.
This simplifies driver wrapper operations and removes last direct
struct hostapd_data dereferences from driver_nl80211.c. In addition,
some of the TX callbacks are now fixed for secondary BSSes.
This fixes deauth/disassoc frames in secondary BSSes when using
multi-BSSID. In addition, it reduces need to dereference
struct hostapd_data inside driver wrappers.
NO_WEXT can be defined to disable all remaining WEXT uses from
driver_nl80211.c. This breaks some functionality, so the code is still
in use by default. Anyway, the new #ifdef blocks make it easy to search
for areas that need to be converted to nl80211.
Instead of adding a new driver_ops for fetching neighbor BSS data (that
nl80211 driver interface had to scan during initialization), share the
same scan operations that wpa_supplicant is using. This gets rid of
duplicated scan code in driver_nl80211.c (and better yet, removes large
part of old WEXT code).
hostapd interface initialization is now completed in a callback, if
needed, i.e., he_features channel/hw_mode selection can use as much time
as needed. This can also help with radar detection in the future.
hostapd ended up with unregistered send_mlme() in commit
9f324b61ba. Fix this by registering the
handler both for wpa_supplicant-AP and hostapd use. [Bug 310]
Use a parameter structure to pass in information that can be more easily
extended in the future. Include some of the parameters that were
previously read directly from hapd->conf in order to reduce need for
including hostapd/config.h into driver wrappers.
This was not documented properly and was not really used nor would it be
suitable to be used in generic way as it was implemented. It is better
to just remove the parameter since there does not seem to be any
reasonable use for it.
nl80211 interface has a trivial bug that prevents it to work correctly
with channel 14. Channel frequency is erroneously 2848 instead of 2484.
To correct it just apply this patch. [Bug 308]
This merges the driver wrapper implementations to use the same
implementation both for hostapd and wpa_supplicant operations to avoid
code duplication.
This commit merges the driver_ops structures and implementations from
hostapd/driver*.[ch] into src/drivers. This is only an initial step and
there is room for number of cleanups to share code between the hostapd
and wpa_supplicant parts of the wrappers to avoid unnecessary source
code duplication.
Need to set WEP keys before requesting authentication in order to get
Shared Key authentication working. Previously, the WEP keys were not set
at all when using SME in wpa_supplicant.
IEEE 802.11r KDF uses key length in the derivation and as such, the PTK
length must be specified correctly. The previous version was deriving
using 512-bit PTK regardless of the negotiated cipher suite; this works
for TKIP, but not for CCMP. Update the code to use proper PTK length
based on the pairwise cipher.
This fixed PTK derivation for both IEEE 802.11r and IEEE 802.11w (when
using AKMP that specifies SHA-256-based key derivation). The fixed
version does not interoperate with the previous versions. [Bug 307]
mac80211 does not use this type of Michael MIC event, so this is not
really used and proper Michael MIC failure processing will be added
using an nl80211 event once that gets added into wireless-testing.git.
It looks like both new nl80211 operations (scan and auth/assoc) end up
being added in Linux 2.6.30, so we do not need to maintain the backwards
compatibility code in wpa_supplicant.
Update credential to only include a single authentication and
encryption type in case the AP configuration includes more than one
option. Without this, the credential would be rejected if the AP was
configured to allow more than one authentication type.
A new network block parameter, scan_freq, can be used to specify subset
of frequencies to scan. This can speed up scanning process considerably
if it is known that only a small subset of channels is actually used in
the network. A union of configured frequencies for all enabled network
blocks is used in scan requests.
Currently, only driver_nl80211.c has support for this functionality.
For example, following parameter marks 2.4 GHz channels 1, 6, 11 to be
scanned: scan_freq=2412 2437 2462
Move the shared IEEE 802.11w enum definition into src/common/defs.h to
avoid redefinition when both configuration structures are included into
the same file.
The memcpy was using incorrect size (of pointer; should have been of
data structure) for the client address. This ended up working on 64-bit
targets, but left part of the address uninitialized on 32-bit targets.
This version is adding the configuration option (mode=2) for this and
driver capability reporting to figure out whether AP mode can be used.
However, this does not actually implement any real functionality yet.
Need to set drv->ifindex before calling set_mode(). In addition, set the
mode before setting the interface up to avoid having to set it down
again.
Add more useful error message on mode changes.
All these driver handlers can be implemented in associate() handler
which gets all the needed information in the parameters structure. The
old functions that provided only a single parameter will be removed
eventually to clean up the driver_ops structure, so driver wrappers
should start using the newer mechanism.
This can be used, e.g., with mac80211-based Linux drivers with
nl80211. This allows over-the-air FT protocol to be used (IEEE
802.11r).
Since the nl80211 interface needed for this is very recent (added
today into wireless-testing.git), driver_nl80211.c has backwards
compatibility code that uses WEXT for association if the kernel does
not support the new commands. This compatibility code can be
disabled by defining NO_WEXT_COMPAT. That code will also be removed
at some point to clean up driver_nl80211.c.
On "eap_tnc_process" function error case, data->in_buf keeps reference
to a local scope variable. For example this will cause segmentation
fault in "eap_tnc_deinit" function "wpabuf_free(data->in_buf)"
statement.
This was broken by 510c02d4a3 which added
validation of eap_ttls_phase2_eap_init() return value. The main problem
in the code trying to initialize a new phase 2 EAP method
unconditionally; this should only happen if there is a new method in the
inner method sequence.
This is based on a patch and report by Masashi Honma
<honma@ictec.co.jp>. The issue is more generic than just TNC, though,
since failure to initialize any phase 2 EAP method can result in NULL
dereference.
On PEAP(TNC), hostapd integrated RADIUS server doesn't return
EAP-Failure when "Recommendation = none". So, EAP data retransmittion
occurs.
My co-worker "Ryuji Ohba" made below patch.
hostapd will now go through the RIC Request and process each RDIE. Only
WMM TSPEC requests are currently supported; all other request
descriptors will be declined.
RIC Response is written by hostapd and verified by wpa_supplicant (MIC
validation). wpa_supplicant does not yet have code to notify the driver
about the resource request results.
This adds first part of FT resource request as part of Reassocition
Request frame (i.e., FT Protocol, not FT Resource Request Protocol).
wpa_supplicant can generate a test resource request when driver_test.c
is used with internal MLME code and hostapd can verify the FTIE MIC
properly with the included RIC Request.
The actual RIC Request IEs are not processed yet and hostapd does not
yet reply with RIC Response (nor would wpa_supplicant be able to
validate the FTIE MIC for a frame with RIC Response).
Windows XP and Vista clients can get confused about EAP-Identity/Request
when they probe the network with EAPOL-Start. In such a case, they may
assume the network is using IEEE 802.1X and prompt user for a
certificate while the correct (non-WPS) behavior would be to ask for the
static WEP key. As a workaround, use Microsoft Provisioning IE to
advertise that legacy 802.1X is not supported.
This seems to make Windows ask for a static WEP key when adding a new
network, but at least Windows XP SP3 was still marking IEEE 802.1X
enabled for the network. Anyway, this is better than just leaving the
network configured with IEEE 802.1X and automatic WEP key distribution.
When using the internal TLS implementation, EAP-FAST unauthenticated
provisioning ends up proposing multiple cipher suites. It looks like
Cisco AP (at least 350 and 1200 series) local authentication server does
not know how to search cipher suites from the list and seem to require
that the last entry in the list is the one that it wants to use.
However, TLS specification requires the list to be in the client
preference order. As a workaround, ass anon-DH AES-128-SHA1 again at the
end of the list to allow the Cisco code to find it.
This fixed EAP-FAST provisioning with the following IOS version:
Cisco IOS Software, C350 Software (C350-K9W7-M), Version 12.3(8)JEA3,
RELEASE SOFTWARE (fc2)
Compiled Wed 21-Nov-07 14:08 by ccai
This is just there very first step on being able to do something with
wireless LAN on Vista. There is some example code for requesting a scan,
but it does not work in its current form. Anyway, this adds a wpa_printf
noting that Native 802.11 drivers are not yet supported.
This is done with wired interfaces to fix IEEE 802.1X authentication
when the authenticator uses the group address (which should be happening
with wired Ethernet authentication).
This allows wpa_supplicant to complete wired authentication successfully
on Vista with a NDIS 6 driver, but the change is likely needed for
Windows XP, too.
Do not use just the driver name for this since driver_ndis.c supports
both wired and wireless NDIS drivers and needs to indicate the driver
type after initialization.
Calculate the estimated medium time using integer variables since there
is no real need to use floating point arithmetics here. In addition,
make sure there is no division by zero regardless of how invalid the
request from the station is. Reject invalid parameters and refuse
requests that would take most of the bandwidth by themselves.
Add test code into wpa_supplicant mlme.c to allow WMM-AC negotiation to
be tested with driver_test.
The new file wps_nfc.c and ndef.c implements NFC device independent
operation, wps_nfc_pn531.c implements NFC device dependent operation.
This patch is only for the following use case:
- Enrollee = wpa_supplicant
- Registrar = hostapd internal Registrar
Following NFC methods can be used:
- Enrollee PIN with NFC
- Registrar PIN with NFC
- unencrypted credential with NFC
Encrypted credentials are not supported.
Enrollee side operation:
Registrar side operation:
Example configuration.
CONFIG_WPS=y
CONFIG_WPS_NFC=y
CONFIG_WPS_NFC_PN531=y
I used NFC device "NXP PN531". The NFC device access method is
confidential, so I used outer library. Please download below files from
https://www.saice-wpsnfc.bz/index.php
[WPS NFC Library]
WpsNfcLibrary/WpsNfc.h
WpsNfcLibrary/WpsNfcType.h
WpsNfcLibrary/WpsNfcVersion.h
WpsNfcLibrary/linux/libnfc_mapping_pn53x.dll
WpsNfcLibrary/linux/wpsnfc.dll
[NFC Reader/Writer Kernel Driver]
NFCKernelDriver-1.0.3/linux/kobj/sonyrw.ko
<WiFi test>
The hostapd/wpa_supplicant with this patch passed below tests on
"Wi-Fi WPS Test Plan Version 1.6".
4.2.5 Add device using NFC Method with password token
(I used SONY STA instead of NXP STA.)
4.2.6 Add device using NFC Method with configuration token
5.1.9 Add to AP using NFC Method with password token
through internal registrar
(I used SONY AP instead of NXP AP.)
5.1.10 Add to AP using NFC Method with configuration token
through internal registrar
This updates the terminogy to match with the final WMM specification. In
addition, some of the WMM TSPEC structure fields were in incorrect order
and used without byte order swapping. Those are also taken care of this
cleanup patch.
The EAP server state machine will need to have special code in
getDecision() to avoid starting passthrough operations before having
completed Identity round in the beginning of reauthentication. This was
broken when moving into using the full authenticator state machine from
RFC 4137 in 0.6.x.
The old behavior of generating new DH keys can be maintained for non-OOB
cases and only OOB (in this case, with UFD) will use the pre-configured
DH keys to allow the public key hash to be checked.
Not all embedded devices have USB interface and it is useful to be able
to remove unneeded functionality from the binary. In addition, the
current implementation has some UNIX specific calls in it which may make
it not compile cleanly on all target systems.
Reduce startWhen from 3 to 1 second if WPS is included in the build.
While this is done regardless of runtime WPS configuration, it is fine
to use a smaller value here in general. This cuts two seconds out from
WPS negotiation if the driver does not support addition of WPS IE into
the (Re)Association Request frame.
Previously, both CONFIG_IEEE80211W=y and CONFIG_IEEE80211R=y were needed
to enable SHA256-based key handshake (WPA-PSK-SHA256 and
WPA-EAP-SHA256). This can now be done with just CONFIG_IEEE80211W=y.
These flags are used to mark which values (level, noise, qual) are
invalid (not available from the driver) and whether level is using dBm.
D-Bus interface will now only report the values that were available.
If session resumption fails for any reason, do not try it again because
that is just likely to fail. Instead, drop back to using full
authentication which may work. This is a workaround for servers that do
not like session resumption, but do not know how to fall back to full
authentication properly.
This fixes an issue where two AKA'/Challenge messages are received when
resynchronizing SEQ#. Previously, this used to trigger an authentication
failure since the second Challenge message did not duplicate AT_KDF.
This does not actually send out separate scan requests for each SSID,
but the debug output can be used to test scan2() functionality with
multiple SSIDs.
This can be used to provide support for scanning multiple SSIDs at a
time to optimize scan_ssid=1 operations. In addition, Probe Request IEs
will be available to scan2() (e.g., for WPS PBC scanning).
For example, -Dnl80211,wext could be used to automatically select
between nl80211 and wext. The first driver wrapper that is able to
initialize the interface will be used.
This workaround was needed with some drivers that used WEXT, but there
is no known nl80211-enabled driver that would need this, so lets get rid
of the extra delay.
The driver wrappers can now inform wpa_supplicant how many SSIDs can
be used in a single scan request (i.e., send multiple Probe Requests
per channel). This value is not yet used, but it can eventually be used
to allow a new scan command to specify multiple SSIDs to speed up
scan_ssid=1 operations. In addition, a warning could be printed if
scan_ssid=1 is used with a driver that does not support it
(max_scan_ssids=0).
