1. The comparison between SCI's of two servers with identical priority
is broken, and would always return TRUE. Just use os_memcmp(), which
provides the ordering we need.
2. If no peer can be key server but this instance can, then become the
key server.
3. The ordering of blocks between peer as key server and ourself as key
server overwrites settings. Simple reordering fixes this.
4. Default to being the key server, so that we advertise our ability in
the MKPDUs we send. That's the only way peers can know we can be key
server. Cleared automatically as soon as we find a better peer.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
There's no need to have a separate variable and open-code a more
complicated version of this, just use is_broadcast_ether_addr().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In preparation for adding further command completion support
to hostapd_cli move some cli related utility functions out of
wpa_cli into a new common cli file.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
This commit defines QCA vendor subcommand and attributes for IE based
access control, i.e., the specific configured IE (full IE) is matched
with the frames originated by the Wi-Fi STA / AP to accept or deny the
connection. A specific IE can either be a whitelist or blacklist.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces a new vendor sub command
QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND and associated
attributes to configure GPIO pins.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes wpa_supplicant set default scan IEs to the driver (if the
vendor command is supported). The driver can use these IEs in the scan
requests initiated by the driver itself. Also the driver can merge these
IEs into further scan requests that it receives, in case if the scan
request doesn't carry any of the IEs sent in this command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, HT/VHT state was shown in STATUS based on the configuration
parameter instead of the runtime operational parameters. This could
result in claiming HT/VHT to be enabled even when it was forced to be
disabled due to an incompatible configuration. Clear HT/VHT information
in the STATUS output if HT/VHT has been disabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If params->freq is NULL here, it leads to a segfault. Do not initialize
bss->bandwidth if params->freq is NULL.
Signed-off-by: Chaitanya T K <Chaitanya.Mgit@gmail.com>
Previously, HT capability IE and HT information IE were included in
Beacon and Mesh Peering Open/Confirm frames even if HT is disabled with
disable_ht=1. This patch removes these.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
If a peer stops sending adv_service_instance, we should clear the
existing dev->info.p2ps_instance.
This commit fixes the following scenario:
When peer device stops sending adv_service_instance, wpa_supplicant did
not remove old dev->info.p2ps_instance from device's property. This
variable should be updated as per peer behavior and should be cleared
when peer stops sending this information.
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
Remove the unnecessary os_free() call from p2p_deinit() since
p2p_flush() called just above this takes care of freeing
p2p->after_scan_tx and the second call here ends up being no-op
os_free(NULL) in practice.
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Previously, mesh power management functionality works only with kernel
MPM. Because user space MPM did not report mesh peer AID to kernel,
the kernel could not identify the bit in TIM element. So this patch
reports mesh peer AID to kernel.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This commit introduces a new vendor sub command
QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH and associated
attributes which aim to configure selected frequencies on which the AP
can conditionally switch onto for preferred operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 49fe2ada20 ('OpenSSL: Support
OpenSSL 1.1.0 DH opacity') started using the new accessor functions, but
used incorrect success check for the DH_set0_key() call. This resulted
in dh5_init_fixed() failures and double-free on error path if the build
was linked against OpenSSL 1.1.0. Fix this by checking DH_set0_key()
return value to be 1 for the success case.
Signed-off-by: Jouni Malinen <j@w1.fi>
These control interface event message are used by external programs, so
define them a bit more formally in the header file.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows P2P Listen to be offloaded to device to enhance power
saving.
To start P2P listen offload, from wpa_cli interface, issue the command:
p2p_lo_start <freq> <period> <interval> <count>
To stop P2P listen offload, issue the command:
p2p_lo_stop
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Provides operating frequency in EVENT_ASSOC when IBSS is joined so that
wpa_s->assoc_freq can be updated when any IBSS network is joined.
Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
During the P802.11s draft development, there were separate LISTEN and
IDLE states. However, the current IEEE 802.11 standards uses only the
IDLE state while the implementation called this LISTEN. Rename the state
in the implementation to match the one used in the standard to avoid
confusion. In addition, rename OPEN_{SENT,RCVD} to OPN_{SNT,RCVD} to
match the exact spelling of these states in the standard.
Signed-off-by: Jouni Malinen <j@w1.fi>
OpenSSL 1.1.0 (master branch) apparently ended up modifying the API
after the beta 2 release that was supposed to complete the work. Mark
the variables const to fix the compilation with the modified OpenSSL
API.
Signed-off-by: Jouni Malinen <j@w1.fi>
These elements can be used for pre-standard publication testing of HE
before P802.11ax draft assigns the element ID. The payload of these
vendor specific elements is defined by the latest P802.11ax draft.
Please note that the draft is still work in progress and the element
payload is subject to change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is now annotated as be16, so use it as such in all cases instead of
first storing host byte order value and then swapping that to big endian
in other instances of the same structure. This gets rid of number of
sparse warnings.
Signed-off-by: Jouni Malinen <j@w1.fi>
driver_wired.c pulls in utils/common.h before net/if.h as a workaround
for NetBSD build. This results in IFNAMSIZ getting redefined and sparse
warning about this. Silence that warning by undefining the IFNAMSIZ
definition from common.h to allow the one from net/if.h being used. In
addition, remove duplicated inclusion of net/if.h.
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of a sparse warning and also allows the compatibility of
the declarations to be verified (a missing const declaration is fixed
here as well).
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of number of sparse warnings and also allows the
compatibility of the declarations to be verified (number of missing
const declarations are fixed here as well).
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows the compiler to check that function prototypes match the
implementation. In addition, this gets rid of sparse warnings.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These are called through function pointers, so no need to make the
function symbols directly available outside this file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This converts some of the PAE code to use a design that gets rid
unnecessary warnings from sparse and allows more thorough validation of
byte order operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These are called through function pointers, so no need to make the
function symbols directly available outside this file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These little endian fields were not marked properly and the type case in
the get_unaligned_* helper macros were causing warnings from sparse.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Couple of fsts_id and llt fields were not properly swapped from host
byte order to little endian byte order used in the frames. Fix this and
use the le32 type to make this more consistent and verifiable with
sparse.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Since crypto_openssl.c is now implementing couple of functions
internally, pull in the relevant header files md5.h and aes_wrap.h to
make sure the function declaration are consistent.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Freeing memory for subjectAltName in parse_cert(), will give cert_cb
pointers to freed memory zone that may already been overwritten. Memory
for subjectAltName is released in parse_cert_free().
Signed-off-by: Cedric Izoard <cedric.izoard@ceva-dsp.com>
The "Accepting Additional Mesh Peerings bit == 0" means the peer cannot
accept any more peers, so suppress attempt to open a connection to such
a peer.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This moves pairwise, group, and management group ciphers to various mesh
data structures to avoid having to hardcode cipher in number of places
through the code. While CCMP and BIP are still the hardcoded ciphers,
these are now set only in one location.
Signed-off-by: Jouni Malinen <j@w1.fi>
The AMPE element includes number of optional and variable length fields
and those cannot really be represented by a fixed struct
ieee80211_ampe_ie. Remove the optional fields from the struct and
build/parse these fields separately.
This is also adding support for IGTKdata that was completely missing
from the previous implementation. In addition, Key RSC for MGTK is now
filled in and used when configuring the RX MGTK for a peer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous implementation was incorrect in forcing the MGTK to be used
as the IGTK as well. Define new variable for storing IGTK and use that,
if set, to configure IGTK to the driver. This commit does not yet fix
AMPE element parsing to fill in this information.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends the data structures to allow variable length MGTK to be
stored for RX. This is needed as an initial step towards supporting
different cipher suites.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is initial step in fixing issues in how PMF configuration for RSN
mesh was handled. PMF is an optional capability for mesh and it needs to
be configured consistently in both hostapd structures (to get proper
RSNE) and key configuration (not included in this commit).
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 0603bcb7fe ('hostapd: Process MAC
ACLs on a station association event (SME in driver)') processes MAC ACL
on a station association event for drivers which use AP SME offload but
does not consider the scenario where the drivers offload ACL. This can
result in station disconnection, though the driver accepts the
connection. Address this by avoiding the hostapd ACL check for the
drivers offloading MAC ACL.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit also introduces a new attribute MANDATORY_FREQUENCY_LIST
which aims for AP operation in a channel that ensures best concurrency
sessions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
eloop deinit calls could trigger segmentation fault if the early error
path is hit before eloop_init() gets called.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify that fst_global_init() has been called before deinitializing the
global FST context. This makes it a bit easier to handle failure paths
from initialization.
Signed-off-by: Jouni Malinen <j@w1.fi>
Set max peer links to kernel even when wpa_supplicant MPM is used. This
sets the correct value for the "Accepting Additional Mesh Peerings bit"
in "Mesh Capability field" in "Mesh Configuration element" in the Beacon
frame.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Recent versions of engine_pkcs11 are set up to be autoloaded on demand
with ENGINE_by_id() because they don't need explicit configuration.
But if we *do* want to explicitly configure them with a PKCS#11 module
path, we should still do so.
We can't tell whether it was already initialised, but it's harmless to
repeat the MODULE_PATH command if it was.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Michael Schaller <misch@google.com>
Any data accessible from nla_data() is freed before the
send_and_recv_msgs() function returns, therefore we need to allocate
space for info.flags ourselves.
Signed-off-by: Paul Stewart <pstew@google.com>
gas_address3=1 can now be used to force hostapd to use the IEEE 802.11
standards compliant Address 3 field value (Wildcard BSSID when not
associated) even if the GAS request uses non-compliant address (AP
BSSID).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously all TX status events with wildcard BSSID were ignored. This
did not allow Public Action frame TX status to be processed with the
corrected wildcard BSSID use. Fix this to be allowed. In practice, this
affects only test cases since Action frame TX status was not used for
anything else.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE Std 802.11-2012, 10.19 (Public Action frame addressing) specifies
that the wildcard BSSID value is used in Public Action frames that are
transmitted to a STA that is not a member of the same BSS. hostapd used
to use the actual BSSID value for all such frames regardless of whether
the destination STA is a member of the BSS.
Fix this by using the wildcard BSSID in cases the destination STA is not
a member of the BSS. Leave group addressed case as-is (i.e., the actual
BSSID), since both values are accepted. No such frames are currently
used, though.
This version is still using the AP BSSID value in the Address 3 field
for GAS response frames when replying to a GAS request with AP BSSID
instead of Wildcard BSSID. This is left as a workaround to avoid
interoperability issues with deployed STA implementations that are still
using the non-compliant address and that might be unable to process the
standard compliant case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds the necessary changes to support extraction and use of the
extended capabilities specified per interface type (a recent
cfg80211/nl80211 extension). If that information is available,
per-interface values will be used to override the global per-radio
value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new "timeout" argument to the event message if the nl80211 message
indicates that the connection failure is not due to an explicit AP
rejection message. This makes it easier for external programs to figure
out why the connection failed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the simplest case of SAE group negotiation to occur by
selecting the next available group if the peer STA indicates the
previous one was not supported. This is not yet sufficient to cover all
cases, e.g., when both STAs need to change their groups, but at least
some cases are no covered.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd deinit functions were not ready to handle a case where the data
structures were not fully initialized. Make these more robust to allow
wpa_supplicant mesh implementation to use the current deinit design in
OOM error cases without causing NULL pointer dereferences.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids internal access of structs and also removes the dependency
on the reimplemented TLS PRF functions when EAP-FAST support is not
enabled. Notably, BoringSSL doesn't support EAP-FAST, so there is no
need to access its internals with openssl_get_keyblock_size().
Signed-Off-By: David Benjamin <davidben@google.com>
Most protocols extracting keys from TLS use RFC 5705 exporters which is
commonly implemented in TLS libraries. This is the mechanism used by
EAP-TLS. (EAP-TLS actually predates RFC 5705, but RFC 5705 was defined
to be compatible with it.)
EAP-FAST, however, uses a legacy mechanism. It reuses the TLS internal
key block derivation and derives key material after the key block. This
is uncommon and a misuse of TLS internals, so not all TLS libraries
support this. Instead, we reimplement the PRF for the OpenSSL backend
and don't support it at all in the GnuTLS one.
Since these two are very different operations, split
tls_connection_prf() in two. tls_connection_export_key() implements the
standard RFC 5705 mechanism that we expect most TLS libraries to
support. tls_connection_get_eap_fast_key() implements the
EAP-FAST-specific legacy mechanism which may not be implemented on all
backends but is only used by EAP-FAST.
Signed-Off-By: David Benjamin <davidben@google.com>
Commit 68ae4773a4 ('OpenSSL: Use library
wrapper functions to access cert store') fixed most of these, but missed
a few.
Signed-Off-By: David Benjamin <davidben@google.com>
This makes changes such that hostapd (and wpa_supplicant AP mode)
registers to kernel for specific Action frames instead of generically
registering for all Action frames. This makes it easier for other
programs to register for some Action frames that hostapd does not handle
today without having to somehow coordinate directly with hostapd.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add P2PS config flag only when config_methods are set. This restores the
pre-P2PS behavioer for the cases where Display or Keypad config method
is specified for a peer (i.e., do not add the new P2PS method in that
case).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
eap_proto_sake_errors test case where the result was used after the
failed eap_sake_compute_mic() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
eap_proto_pax_errors test case where the result was used after the
failed eap_pax_mac() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
eap_proto_fast_errors test case where the result was used after the
failed sha1_t_prf() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
wpas_ctrl_error test case where the result was used after the failed
sha256_vector() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
hostapd_oom_wpa2_eap_connect test case where the result is used after
failed md5_vector() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
hostapd_oom_wpa2_eap_connect test case where memcmp is used after failed
hmac_md5() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
hostapd_oom_wpa2_eap test case where memcmp is used after failed
md5_vector() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Check for hmac_sha256() failures and exit from wps_derive_psk() without
printing out the derived keys if anything fails. This removes a valgrind
warning on uninitialized value when running the ap_wps_m3_oom test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In some terminal, verified with gtkterm and teraterm, backspace key is
not properly processed. For instance, type 'abc', 3 times of backspace
key press then '123' shows the result of 'abc123' instead of '123'. To
fix this, add a routine to process '\b' character input when using
edit_simple.c instead of edit.c (i.e., without CONFIG_WPA_CLI_EDIT=y).
Signed-off-by: Siwon Kang <kkangshawn@gmail.com>
If there's ever a driver that, like nl80211, requires radiotap,
we need to have a NEED_RADIOTAP variable to avoid trying to link
the radiotap helpers twice. Introduce that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Commit 4104267e81 ('Fix memory leak on NFC
DH generation error path') modified the generic (non-OpenSSL)
implementation of dh5_init() to free the previously assigned public key,
if any. However, that commit did not modify the OpenSSL specific version
of this function. Add the same change there to maintain consistent
behavior between these two implementations of the same function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 4104267e81 ('Fix memory leak on NFC
DH generation error path') modified dh5_init() behavior in the
non-OpenSSL implementation to free the public key (if any was previously
set). However, this did not update one of the callers to make sure the
publ argument in the call is initialized. This could result in trying to
free invalid pointer and segmentation fault when hostapd or
wpa_supplicant was built against some other crypto library than OpenSSL.
Signed-off-by: Rujun Wang <chinawrj@gmail.com>
BoringSSL added OpenSSL 1.1.0's SSL_get_client_random() and friends in
working towards opaquifying the SSL struct. But it, for the moment,
still looks more like 1.0.2 than 1.1.0 and advertises
OPENSSL_VERSION_NUMBER as such. This means that there is no need to
define those in BoringSSL and defining them causes conflicts. (C does
not like having static and non-static functions with the same name.)
As requested, this is conditioned on defined(BORINGSSL_API_VERSION) so
wpa_supplicant may continue to support older BoringSSLs for a time.
(BoringSSL revisions without the accessors predate BoringSSL maintaining
a BORINGSSL_API_VERSION.)
Also add a missing opensslv.h include. tls_openssl.c is sensitive to
OPENSSL_VERSION_NUMBER, so it should include the header directly rather
than rely on another header to do so.
Signed-off-by: David Benjamin <davidben@google.com>
Spurious newlines output while writing the config file can corrupt the
wpa_supplicant configuration. Avoid writing these for the network block
parameters. This is a generic filter that cover cases that may not have
been explicitly addressed with a more specific commit to avoid control
characters in the psk parameter.
Signed-off-by: Paul Stewart <pstew@google.com>
WPA/WPA2-Personal passphrase is not allowed to include control
characters. Reject a Credential received from a WPS Registrar both as
STA (Credential) and AP (AP Settings) if the credential is for WPAPSK or
WPA2PSK authentication type and includes an invalid passphrase.
This fixes an issue where hostapd or wpa_supplicant could have updated
the configuration file PSK/passphrase parameter with arbitrary data from
an external device (Registrar) that may not be fully trusted. Should
such data include a newline character, the resulting configuration file
could become invalid and fail to be parsed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
One of supported code paths already allows this scenario. It is used if
driver doesn't report NL80211_ATTR_DEVICE_AP_SME and doesn't support
monitor interface. In such situation:
1) We don't quit if subscribing for WLAN_FC_STYPE_PROBE_REQ fails
2) We don't try subscribing for WLAN_FC_STYPE_ACTION
3) We fallback to AP SME mode after failing to create monitor interface
4) We don't quit if subscribing for WLAN_FC_STYPE_PROBE_REQ fails
Above scenario is used, e.g., with brcmfmac. As you can see - thanks to
events provided by cfg80211 - it's not really required to receive Probe
Request or action frames.
However, the previous implementation did not allow using hostapd with
drivers that:
1) Report NL80211_ATTR_DEVICE_AP_SME
2) Don't support subscribing for PROBE_REQ and/or ACTION frames
In case of using such a driver hostapd will cancel setup after failing
to subscribe for WLAN_FC_STYPE_ACTION. I noticed it after setting flag
WIPHY_FLAG_HAVE_AP_SME in brcmfmac driver for my experiments.
This patch allows working with such drivers with just a small warning
printed as debug message.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
This reduces duration that private keying material might remain in the
process memory by clearing wpabuf data used in WPS operations when there
is possibility of the buffer including keys or related material.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new parameter allows hostapd to add Vendor Specific elements into
(Re)Association Response frames similarly to the way vendor_elements
parameter can be used for Beacon and Probe Response frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The OpenSSL 1.1.0 Beta 2 release made DH opaque and that broke
compilation of crypto_openssl.c. Fix this by using the new accessor
functions when building against OpenSSL 1.1.0 or newer.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 66d464067d ('FT: Register RRB
l2_packet only if FT-over-DS is enabled') disabled RRB l2_packet socket
if ft_over_ds is disabled, but this socket is required for FT
over-the-air, too (FT key distribution). Enable the socket regardless of
ft_over_ds setting if FT is enabled.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
This adds QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION and the attributes used
with these commands.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows local GO to fetch the P2P Interface Address of a P2P Client
in the group based on the P2P Device Address for the client. This
command should be sent only on a group interface (the same peer may be
in multiple concurrent groups).
Usage:
P2P_GROUP_MEMBER <P2P Device Address>
Output:
<P2P Interface Address>
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
Trigger an event when wpa_supplicant accepts an invitation to re-invoke
a persistent group. Previously wpa_supplicant entered group formation
without triggering any specific events and it could confuse clients,
especially when operating with a driver that does not support
concurrency between P2P and infrastructure connection.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
The os_snprintf() call here cannot really fail in practice, but since
its result was stored into the local variable and not checked, static
analyzers could warn about the unused assignment. Clean this up by
checking the return value.
Signed-off-by: Jouni Malinen <j@w1.fi>
Set the global RRM flag if global RRM is supported by the device. Also,
allow RRM in (Re)Association Request frame if the global RRM flag is
set.
Signed-off-by: Beni Lev <beni.lev@intel.com>
This flag indicates that RRM can be used in (Re)Association Request
frames, without supporting quiet period.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Register to receive Radio Measurement Request frames since LCI request
is supported by wpa_supplicant.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add FTM range request via RRM. The AP sends Radio measurement request
with FTM range request as a request for the receiving STA to send FTM
requests to the given list of APs. The neighbor report part of the
request is taken from the neighbor database.
The control interface command is:
REQ_RANGE <dst addr> <rand_int> <min_ap> <responder> [<responder>..]
dst addr: MAC address of an associated STA
rand_int: Randomization Interval (0..65535) in TUs
min_ap: Minimum AP Count (1..15); minimum number of requested FTM ranges
between the associated STA and the listed APs
responder: List of BSSIDs for neighboring APs for which a measurement
is requested
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add a hostapd control interface command REQ_LCI to request LCI from an
associated station using radio measurement.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Save RM enabled capability element of an associating station if radio
measurement is supported in its capability field.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Process Neighbor Report Request frame and send Neighbor Report Response
frame based on the configured neighbor report data.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add a configurable neighbor database that includes the content of
Nighbor Report element, LCI and Location Civic subelements and SSID.
All parameters for a neighbor must be updated at once; Neighbor Report
element and SSID are mandatory, LCI and civic are optional. The age of
LCI is set to the time of neighbor update.
The control interface API is:
SET_NEIGHBOR <BSSID> <ssid=SSID> <nr=data> [lci=<data>] [civic=<data>]
To delete a neighbor use:
REMOVE_NEIGHBOR <BSSID> <SSID>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Extend the radio_measurements parameter to save all the supported
RRM capabilities as it's used in RM enabled capabilities element.
Make this parameter not directly configurable via config file (though,
keep the radio_measurements parameter for some time for backwards
compatibility). Instead, add a configuration option to enable neighbor
report via radio measurements. Other features can be added later as
well.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add a function that parses SSID in text or hex format. In case of the
text format, the SSID is enclosed in double quotes. In case of the hex
format, the SSID must include only hex digits and not be enclosed in
double quotes. The input string may include other arguments after the
SSID.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Make the function available as part of the wpabuf API.
Use this renamed function where possible.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
The hostapd "POLL_STA <addr>" control interface command can be used to
check whether an associated station ACKs a QoS Data frame. The received
ACK for such a frame is reported as an event message ("AP-STA-POLL-OK
<addr>").
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The optional tx=0 parameter can be added to the hostapd
DEAUTHENTICATE/DISASSOCIATE command to request disconnection without
transmitting the Deauthentication/Disassociation frame to the STA.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows external programs to fetch the driver inactivity value for a
specific STA ("STA <addr>" hostapd control interface command).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new VENDOR_ELEM value 14 can now be used to add a vendor element
into Probe Request frames used by non-P2P active scans.
For example:
VENDOR_ELEM_ADD 14 dd05001122330a
and to clear that:
VENDOR_ELEM_REMOVE 14 *
Signed-off-by: Jouni Malinen <j@w1.fi>
Implement configure_data_frame_filters() callback by using
the net-sysfs interfaces (if these are available).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add a new function declaration that will allow wpa_supplicant to request
the driver to configure data frame filters for specific cases.
Add definitions that will allow frame filtering for stations as
required by Hotspot 2.0:
1. Gratuitous ARP
2. Unsolicited NA
3. Unicast IP packets encrypted with GTK
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
If a legacy client with no P2P PS support is trying to connect to
a P2P GO, the driver should know that, and change its PS behavior
accordingly.
Add a parameter to hostapd_sta_add_params() indicating if P2P PS is
supported by the station and pass this parameter to kernel with nl80211
driver when the station is added/set.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Fix a possible memory leak in decode_tunnel_passwords() if an invalid
passphrase is received from the RADIUS server.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
This was previously handled for the case where the non-success
Invitation Response frame was sent out during the Listen phase. However,
in the case the Action frame TX ended up getting scheduled when the
Search phase scan had already started (e.g., due to the driver reporting
Invitation Request RX late enough for the Listen-to-Search transition
having already started), the postponed Action frame TX status processing
did not cover the specific case of non-success Invitation Response. This
could result in the p2p_find operation getting stopped (stuck in SEARCH
state) unexpectedly.
Fix this by calling p2p_check_after_scan_tx_continuation() from
Invitation Response TX callback handler if the invitation was rejected.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The Secure bit in the Key Information field of EAPOL-Key frames is
supposed to be set to 1 when there is a security association. This was
done for other frames, but not for the EAPOL-Key Request frame where
supplicant is requesting a new PTK to be derived (either due to Michael
MIC failure report Error=1 or for other reasons with Error=0). In
practice, EAPOL-Key Request frame is only sent when there is a PTK in
place, so all such frames should have Secure=1.
Signed-off-by: Jouni Malinen <j@w1.fi>
This struct in the union is empty, but the design of using a zero-length
u8 array here is not fully compatible with C++ and can result in
undesired compiler warnings. This struct is not used anymore, so it can
be removed from the struct ieee80211_mgmt definition to complete the
changes started in commit d447cd596f
('Updates for stricter automatic memcpy bounds checking').
Signed-off-by: Jouni Malinen <j@w1.fi>
This struct in the union is empty, but the design of using a zero-length
u8 array here is not fully compatible with C++ and can result in
undesired compiler warnings. Since there are no non-IE fields in the
Probe Request frames, get the location of the variable length IEs simply
by using the pointer to the frame header and the known header length.
Signed-off-by: Jouni Malinen <j@w1.fi>
This struct in the union is empty, but the design of using a zero-length
u8 array here is not fully compatible with C++ and can result in
undesired compiler warnings. Since there are no non-IE fields in the
Probe Request frames, get the location of the variable length IEs simply
by using the pointer to the frame header and the known header length.
Signed-off-by: Jouni Malinen <j@w1.fi>
This reverts commit 4ca16b5fd7.
Configuration for this will be done using a previously assigned more
generic command. This new command
QCA_NL80211_VENDOR_SUBCMD_SET_TXRX_AGGREGATION has not been used in any
driver version and won't be used, so the assigned command id can be
freed for future use.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no strong need for pulling in linux/if_ether.h here since all
that is needed if ETH_P_IP and we already cover multiple other ETH_P_*
values in utils/common.h.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was only used for providing an option to use linux/if_packet.h
instgead of netpacket/packet.h in src/ap/iapp.c. However,
netpacket/packet.h is nowadays commonly available and hostapd already
depends on it through src/l2_packet/l2_packet_linux.c, so there is no
need to continue to provide this option for the kernel header.
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of need to include linux/if_vlan.h and additional defines
in vlan_ioctl.c to avoid issues with missing definitions in libc
headers.
Signed-off-by: Jouni Malinen <j@w1.fi>
Due to both <netinet/in.h> (in "utils/includes.h") and <linux/in6.h> (in
<linux/if_bridge.h>) being included, the in6_addr is being redefined:
once from the C library headers and once from the Linux kernel headers.
This causes some build failures with for example the musl C library:
In file included from /usr/include/linux/if_bridge.h:18,
from ../src/ap/vlan_init.c:17:
/usr/include/linux/in6.h:32: error: redefinition of 'struct in6_addr'
/usr/include/linux/in6.h:49: error: redefinition of 'struct sockaddr_in6'
/usr/include/linux/in6.h:59: error: redefinition of 'struct ipv6_mreq'
Mixing C library and Linux kernel headers is a bit problematic [1] and
should be avoided if possible [2]. In order to fix this, define just the
macros needed from <linux/if_bridge.h> as done in Busybox for the brctl
applet [3].
[1] https://sourceware.org/bugzilla/show_bug.cgi?id=15850
[2] http://www.openwall.com/lists/musl/2015/10/06/1
[3] https://git.busybox.net/busybox/commit/?id=5fa6d1a632505789409a2ba6cf8e112529f9db18
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
With this, vlan_init.c does not need any special header files anymore
and vlan_ifconfig.c does not need hostapd-specific header files that
might conflict with net/if.h on NetBSD.
Signed-off-by: Jouni Malinen <j@w1.fi>
Move the ioctl-based VLAN implementation to a separate file to avoid
need for conditional blocks within vlan_ioctl.c. This removes the
internal CONFIG_VLAN_NETLINK define, i.e., this is now used only in
build configuration (.config) to select whether to include the
vlan_util.c (netlink) or vlan_ioctl.c (ioctl) implementation of the
functions.
Signed-off-by: Jouni Malinen <j@w1.fi>
caddr_t is legacy BSD and should be avoided [1]. While glibc may still
use __caddr_t as the type, Linux kernel does not (it is "void __user *
ifru_data").
This fixes compile errors with the musl libc:
../src/ap/vlan_init.c: In function 'br_delif':
../src/ap/vlan_init.c:218:18: error: '__caddr_t' undeclared (first use in this function)
ifr.ifr_data = (__caddr_t) args;
[1] http://stackoverflow.com/questions/6381526/what-is-the-significance-of-caddr-t-and-when-is-it-used
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
cfg80211 reports a deauth/disassoc event when internally clearing
connection with the previous BSS. Ignore that event to allow the new
connect command to complete.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier for drivers that use the Connect command instead of
separate Auth+Assoc commands to determine when to use reassociation
instead of association. Matching changes are still needed in cfg80211 to
allow this parameter to be used, but it is safe for wpa_supplicant to
start including this attribute now since it will be ignored by older
cfg80211 versions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
pmksa->pmk or pmksa->pmkid cannot be NULL since they are arrays. Remove
the unnecessary NULL checks and use the provided pmksa pointer directly
to simplify the implementation. (CID 138519)
Signed-off-by: Jouni Malinen <j@w1.fi>
Interface additions/removals are not guaranteed to be for the driver
listening to the kernel events. As such, send the events to
wpa_supplicant_event_global() which can then pick the correct interface
registered with wpa_supplicant to send the event to.
Signed-off-by: Roy Marples <roy@marples.name>
Commit 1889af2e0f ('VLAN: Separate station
grouping and uplink configuration') added an ap_sta_set_vlan() function
that gets called from pmksa_cache_auth.c. This broke CONFIG_IBSS_RSN=y
build if src/ap/sta_info.c did not get included in the build, i.e., if
CONFIG_AP=y was not set.
Fix this by making the ap_sta_set_vlan() call conditional on
CONFIG_NO_VLAN being undefined and define this for CONFIG_IBSS_RSN=y
builds. This is fine for wpa_supplicant since CONFIG_AP=y case was
already defining this. For hostapd, this function call is not needed for
CONFIG_NO_VLAN case either.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This patch add functionality of mesh SAE PMKSA caching. If the local STA
already has peer's PMKSA entry in the cache, skip SAE authentication and
start AMPE with the cached value.
If the peer does not support PMKSA caching or does not have the local
STA's PMKSA entry in the cache, AMPE will fail and the PMKSA cache entry
of the peer will be removed. Then STA retries with ordinary SAE
authentication.
If the peer does not support PMKSA caching and the local STA uses
no_auto_peer=1, the local STA can not retry SAE authentication because
NEW_PEER_CANDIDATE event cannot start SAE authentication when
no_auto_peer=1. So this patch extends MESH_PEER_ADD command to use
duration(sec). Throughout the duration, the local STA can start SAE
authentication triggered by NEW_PEER_CANDIDATE even though
no_auto_peer=1.
This commit requires commit 70c93963ed
('SAE: Fix PMKID calculation for PMKSA cache'). Without that commit,
chosen PMK comparison will fail.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends the wpa_supplicant PMKSA_FLUSH control interface command to
allow the PMKSA list from the authenticator side to be flushed for AP
and mesh mode. In addition, this adds a hostapd PMKSA_FLUSH control
interface command to flush the PMKSA entries.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends the wpa_supplicant PMKSA control interface command to allow
the PMKSA list from the authenticator side to be listed for AP and mesh
mode. In addition, this adds a hostapd PMKSA control interface command
to show the same list for the AP case.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This group capability bit was previously added unconditionally which
could result in the P2P Client assuming the functionality is available
even though the GO would always reject the request (not reply to it with
an assigned IP address) during the 4-way handshake.
Fix this by advertising the capability only if the GO configuration
allow IP address assignment to be completed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 732b1d20ec ('nl80211: Clean up
ifidx properly if interface in a bridge is removed') added
drv->if_indices_reason array similarly to the previously used
drv->if_indices. However, it had a copy-paste error here on the error
path where a reallocation failure after at least one successful
reallocation would result in the drv->if_indices being overridden
instead of restoring drv->if_indices_reason to the old value. Fix this
by setting the correct variable on the error path. (CID 138514)
Signed-off-by: Jouni Malinen <j@w1.fi>
SMPS mode is applicable only for HT and including an attribute to
configure it when HT is disabled could result in the AP start operation
failing. Fix this by adding the attribute only in cases where HT is
enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Since this function needs to allocate memory, it might fail. Check that
the returned memory pointer is not NULL before trying to parse the
output.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While this function could return NULL if the parameter issued to it were
NULL, that does not really happen here. Anyway, since this can result in
a warning from a static analyzer that does can see the return NULL
without fully understanding what it means here, check the return value
explicitly against NULL to avoid false warnings.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Since commit cb05808c46 ('nl80211: Generic
Linux master interface support for hostapd'), hostapd is listening for
EAPOL frames on any master which the interface is enslaved under.
This commit allows hostapd to support network hierarchy in which the
interface is enslaved under some master which in turn is enslaved under
a bridge.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
In scenarios where only DFS channels are available (e.g., outdoor,
special country codes), hostapd must be able to handle situations
where all are unavailable.
The two possibilities to get there are
1) while operating on the last available DFS channel a radar is
detected
2) hostapd is started while all channels are unavailable
In both cases, hostapd instead of terminating should better
wait for the NOPs to pass and re-try operation after the CAC.
This patch provides that feature by using the condition
(iface->state == HAPD_IFACE_DFS && !iface->cac_started)
as NOP mode signature to retry operation from within
hostapd_dfs_nop_finished().
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Upon receiving FST setup request on old band, the peer is searched on
new band. The assumption is that MB IE from this peer on new band
previously received either in assoc event or in FST setup request.
There are cases in which above assumption doesn't work, peer is not
found and session setup fails. For example:
- STA connects over 11ac. Due to driver limitation, MB IE is not included
in assoc event
- STA connects over 11ad. MB IE included in assoc event.
- FST session established on 11ac band, with AP as initiator. i.e. FST
setup request sent in AP=>STA direction. STA searches for peer's (AP)
MB IE on 11ad band which exists.
- FST switch occur
- FST session established on 11ad band, with STA as initiator. i.e. FST
setup request sent in STA=>AP direction. AP searches for peer's (STA)
MB IE on 11ac band which are absent.
For fixing the above, consider also peers without MB IE as candidates in
the search algorithm.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
In the 60 GHz band, service discovery management frames are sent over
the control PHY and have a smaller maximum frame size (IEEE Std
802.11ad-2012, 21.4.3.2). Fix the code to use sufficiently small
fragment size when operating in the 60 GHz band.
The 60 GHz fragment size (928) is derived from the maximum frame size
for control PHY (1023) and subtracting 48 bytes of header size, and some
spare so we do not reach frames with the absolute maximum size.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Add a new 'use_driver_iface_addr' configuration parameter to allow use
of the default interface address generated by the driver on interface
creation. This can be useful when specific MAC addresses were allocated
to the device and we want to use them for multi-BSS operation.
Signed-off-by: Eliad Peller <eliad@wizery.com>
There is a race condition in which AP might receive the EAPOL-Start
frame (from the just-associated station) before the TX completion of the
Association Response frame. This in turn will cause the EAPOL-Start
frame to get dropped, and potentially failing the connection.
Solve this by saving EAPOL frames from authenticated-but-not-associated
stations, and handling them during the Association Response frame TX
completion processing.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Add UDP support for ctrl_iface:
New config option could be set:
CONFIG_CTRL_IFACE=udp
CONFIG_CTRL_IFACE=udp-remote
CONFIG_CTRL_IFACE=udp6
CONFIG_CTRL_IFACE=udp6-remote
And hostapd_cli usage:
hostapd_cli -i localhost:8877
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This is preparation for sharing a single implementation for ctrl_iface
functionality in wpa_supplicant and hostapd.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Update the peer WFD IE information based on WFD elements received in
Provision Discovery Response and GO Negotiation Response frames.
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Kyeong-Chae Lim <kcya.lim@samsung.com>
In case a Probe Request frame is received from a known peer P2P Device,
update the listen channel based on the P2P attributes in the Probe
Request frame. This can be useful for cases where the peer P2P Device
changed its listen channel, and the local P2P device is about to start a
GO Negotiation or invitation signaling with the peer.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Currently, when scan is stuck in the kernel/driver/fw,
the nl80211 driver tries to recover by faking a SCAN_RESULTS flow.
However, the scan is still stuck in the kernel/driver/fw.
To avoid that stuck request, abort it upon scan timeout.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
syms is defined only for WPA_TRACE_BFD:
../src/utils/trace.c: In function ‘wpa_trace_deinit’:
../src/utils/trace.c:372:7: error: ‘syms’ undeclared (first use in this function)
free(syms);
^
../src/utils/trace.c:372:7: note: each undeclared identifier is reported only once for each function it appears in
make: *** [../src/utils/trace.o] Error 1
make: *** Waiting for unfinished jobs....
Add appropriate #ifdef.
Signed-off-by: Eliad Peller <eliad@wizery.com>
When building P2P IE for Probe Request frames in P2P scan, add the
device information attribute if the 60 GHz band is included in the scan,
since this is required by the P2P specification.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Expose the functions wpas_get_bands() and wpas_freq_to_band() and the
enum wpa_radio_work_band, since they will be needed outside
wpa_supplicant.c.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
STT guards the exchange of FST Action frames with the peer station.
It was observed that sometimes Action frames sending is delayed at
driver/FW layers for few hundreds millisec.
Enlarge the STT to overcome such cases.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
In case vendor ACS command returns invalid channel or hardware mode,
complete the interface setup with an error code instead of simply
return, so that hostapd can properly clean up the interface setup.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This tells to the server how long we have been trying to transmit the
message so that the actual time of the message generation can be
determined from receive time (ignoring network delays and only at
accuracy of one second).
For interim updates, only value 0 is used since there are no
retransmissions of the same message. For other accounting messages, the
initial attempt goes out with value 0 and the retransmissions, if
needed, show the number of seconds the message has been waiting in the
queue.
Update the Identifier and Authenticator in the messages whenever
updating the Acct-Delay-Time per RFC 2866, 4.1 requirements.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of using the RADIUS client retransmission design with the old
RADIUS message contents for each retry, trigger a completely new interim
accounting update instance more quickly (using the same schedule as
RADIUS message retransmissions) to improve accounting updates in cases
where RADIUS message delivery fails. This allows the server to get up to
date information from the time the "retry" message was sent instead of
the old information from the time the first failed attempt was sent.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to maintain two implementations of the functionality.
is_zero_ether_addr() is easier to understand, so use it.
Signed-off-by: Jouni Malinen <j@w1.fi>
Using rtnl_link_alloc_cache() is expensive as it fills in all configured
links. Using rtnl_link_get_kernel() is much more lightweight.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
When an interface is removed while it was in a bridge, the bridge was
not removed from the local ifidx list.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
As the Linux variant of l2_packet_init() does not use its own_addr
argument and l2_packet_receive() does not filter on destination MAC
address, this needs to be checked in the callback.
If there are multiple BSSes listening for FT RRB packets, all their
BSSIDs need to be local to the bridge interface. As l2_packet_init() is
going to receive all of them going for any local address, those RRB
messages started turning up on BSSes that were not destinated for and
cluttering logs.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
If the AP is slow, passphrase hashing takes too long to serve the client
before timeout. Extend the Tunnel-Password design to allow a 64
character value to be interpreted as a PSK and send SSID to RADIUS
server. This allows the RADIUS server to either take care of passphrase
hashing or to use raw PSK without such hashing.
This is especially important for FT-PSK with FT-over-air, where hashing
cannot be deferred.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Instead of copying the full struct hostapd_sta_wpa_psk_short, share the
existing entry and use reference counting to check when it needs to be
freed. This allows caching of PSKs derived from passphrases to avoid
having to perform the heavy hashing operation multiple times.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Hashing takes quite some time (can be about one second on a low-power
CPU for each passphrase provided), so hostapd can easily hit the 900 ms
Wi-Fi client authentication deadline (mac80211 uses 3x 300 ms). This can
be fixed by storing the passphrase instead of PSK with the STA and defer
the hashing into the WPA/RSN 4-way handshake, when enumerating all PSKs.
This applies for the case where a RADIUS server is used to store the
per-STA passphrases and this passphrase is delivered as part of the MAC
ACL check during IEEE 802.11 Authentication frame processing.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
The VLAN ifname is limited to the maximum length of IFNAMSIZ, so there
is no need to use heap allocation for it.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
r1_key_holder is an identifier that was always set to zero if unless
configured before.
See 11.6.1.7.4 of IEEE Std 802.11-2012 which reads
"R1KH-ID is a MAC address of the holder of the PMK-R1 in the
Authenticator of the AP"
See 12.2.2 of IEEE Std 802.11-2012 which reads
"Each R0KH-ID and R1KH-ID is assumed to be expressed as a unique
identifier within the mobility domain."
"The R1KH-ID shall be set to a MAC address of the physical entity
that stores the PMK-R1 ..."
Defaulting this to BSSID is a more reasonable value since we have not
rejected the missing r1_key_holder as invalid configuration.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
A malicious station could try to do FT-over-DS with a non WPA-enabled
BSS. When this BSS is located in the same hostapd instance, internal RRB
delivery will be used and thus the FT Action Frame will be processed by
a non-WPA enabled BSS. This processing used to crash hostapd as
hapd->wpa_auth is NULL. If the target BSS is on a different hostapd
instance, it will not listen for these packets and thus not crash.
Fix this by checking hapd->wpa_auth before delivery.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
The FT RRB hostapd packets have a length field. For PULL frames, it
counted the bytes starting with nonce and up to the last before pad. For
RESP frames, it counted the bytes starting with nonce and up to the last
before pad except for 2 bytes. For PUSH frames, it counted the bytes
starting with nonce and up to including pad.
As rounding is done with AES encryption, including pad does not make
sense. Not including the last field before pad does not make sense
either. These were broken in the earlier addition of the 2 octet
pairwise field in commit 1b484d60e5 ('FT:
Include pairwise cipher suite in PMK-R0 SA and PMK-R1 SA').
AES encryption is not affected, as rounding hides the differences. The
packets data_length field is not used, so the differences have no effect
there.
This patch changes the constants to match the bytes used, thus excluding
the pad. To validate the changes, look at remainder modulo 8 of the sum
of the size constants and the padding sizes.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This makes hostapd track Supported Operating Classes information from
the associated STAs. The stored information is available through the STA
control interface command (supp_op_classes row) as a hexdump of the
Supported Operating Classes element starting from the Length field. This
information can be used as input to BSS transition management and
channel switching decisions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Inside management frame TX status callback, print the TX result where it
was missing. This is useful for debugging management frame drops.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
This adds parsing of non-preferred channel list on an MBO AP. The
information in (Re)Association Request and WNM Notification Request
frames is parsed to get the initial value and updates from each
associated MBO STA. The parsed information is available through the STA
control interface command non_pref_chan[i] rows.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the second memory allocation in ieee802_11_send_wnmsleep_resp() were
to fail and ieee80211_11_get_tfs_ie() succeed, the wnmtfs_ie allocation
would not have been freed on the error path.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While refactoring VLAN comparison into vlan_compare(), it was overlooked
that modifications are needed for tagged VLAN support.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
If WPA2 and MBO are enabled, PMF needs to be enabled in hostapd
configuration. If PMF is optional in the configuration, an MBO STA is
required to negotiate use of PMF.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes hostapd parse a received WNM Notification Request frame
subelements and if a WFA MBO cellular data capability subelement is
seen, update the cellular data capability for the STA.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes hostapd parse the MBO attribute in (Re)Association Request
frame and track the cellular data capability (mbo_cell_capa=<val> in STA
control interface command).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This removes multiple copies of wpabuf_resize() following by
wpabuf_put_{buf,data}() with the help of two simple helper functions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add an option to add MBO IE to BSS Transition Management Request frame.
The MBO IE includes the transition reason code, cellular data connection
preference, and, if the disassoc imminent bit is set, it may also
include re-association retry delay. Otherwise, the re-association retry
delay should be set to zero.
The additional BSS_TM_REQ argument uses the following format:
mbo=<reason>:<reassoc delay>:<cell pref>
reason: 0-9
reassoc delay: 0-65535 (seconds; 0 = disabled)
cell pref: 0, 1, 255
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add MBO IE with AP capability attribute to Beacon, Probe Response, and
(Re)Association Response frames to indicate the AP supports MBO.
Add option to add Association Disallowed attribute to Beacon, Probe
Response, and (Re)Association Response frames. Usage:
SET mbo_assoc_disallow <reason code>
Valid reason code values are between 1-5. Setting the reason code to
0 will remove the Association Disallowed attribute from the MBO IE
and will allow new associations.
MBO functionality is enabled by setting "mbo=1" in the config file.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add the transition candidate list to BSS Transition Management Response
frame. The candidates preference is set using the regular wpa_supplicant
BSS selection logic. If the BSS transition request is rejected and
updated scan results are not available, the list is not added.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add a function to derive phy type from frequency and bandwidth
as defined in IEEE Std 802.11ac-2013 Annex C (dot11PHYType).
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add parsing of MBO IE in BSS Transition Management Request frames. If
the MBO IE includes the association retry delay attribute, do not try to
reconnect to the current BSS until the delay time is over.
If the MBO IE includes the cellular data connection preference attribute
or the transition rejection reason attribute, send a message to upper
layers with the data.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add definitions for global operating classes. These definitions will be
used to construct supported operating classes information element.
The operating classes definitions used locally for P2P module will be
removed and included in the general operating classes definitions.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add a helper function to find a certain IE inside IEs buffer by ID and
use this function in several places that implemented similar
functionality locally.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
The recent VLAN changes added an explicit code path that sets vlan_desc
= NULL within ap_sta_set_vlan(). This makes some code analyzers warn
about the debug print that could potentially dereference this pointer.
Silence that warning by verifying the pointer more consistently within
this function.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the driver supports 64-bit TX/RX byte counters, use them directly.
The old 32-bit counter extension is maintained for backwards
compatibility with older drivers.
For nl80211 driver interface, the newer NL80211_STA_INFO_RX_BYTES64 and
NL80211_STA_INFO_TX_BYTES64 attributes are used when available. This
resolves the race vulnerable 32-bit value wrap/overflow. Rework RADIUS
accounting to use these for Acct-Input-Octets, Acct-Input-Gigawords,
Acct-Output-Octets, and Acct-Output-Gigawords, these values are often
used for billing purposes.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Previously, stations were added to the driver only after the
(Re)Association Response frame was acked. In the time period between the
station has acked the (Re)Association Response frame and the time the
station was added to the kernel, the station can already start sending
Data frames, which will be dropped by the hardware/driver. In addition
to the data loss, the driver may ignore NDPs with PM bit set from this
STA.
Fix this by setting/adding the STA with associated flag set to the
driver before the AP sends the (Re)Association Response frame with
status success. If the (Re)Association Response frame wasn't acked,
remove the station from the driver.
Note that setting a station to associated state before the non-AP
station acknowledges the (Re)Association Response frame is not compliant
with the IEEE 802.11 standard that specifically states that a non-AP
station should transition to authenticated/associated state only after
it acknowledged the (Re)Association Response frame. However, this is a
justifiable simplification to work around the issue described above since
1. The station will be removed in case it does not acknowledge the
(Re)Association Response frame.
2. All Data frames would be dropped until the station is set to
authorized state and there are no known issues with processing the
other Class 3 frames during the short window before the
acknowledgement is seen.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add support for drivers that support full AP client state, i.e., can
handle adding stations that are not associated yet. For such drivers,
add a station after processing the authentication request, instead of
adding it in the association response callback.
Doing so is beneficial in cases where the driver cannot handle the add
station request, in which case it is useless to perform the complete
connection establishment.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
This provides means for determining whether the driver supports full AP
station state and setting the needed STA flags for using this
functionality.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Do not use os_random() that uses a low quality PRNG to generate the
anti-clogging token. The construction can be improved upon by replacing
it with a call to os_get_random(), which uses a high quality PRNG. While
the RFC 5931 explictly recommends not to do this ("SHOULD NOT be from a
source of random entropy"), it does still mandate unpredicability ("MUST
be unpredictable"). The anti-clogging token is most unpredictable when
it is taken from a high quality PRNG.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
