In case the current channel has regulatory WMM limitations, take them
into account when filling the WMM element. Also check if the new WMM
element is different from the previous one and if so change the
parameter_set_count to imply stations to look into it.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
When a new station is added, let it have some supported rates
(they're empty without this change), using the basic rates
that it must support to connect.
This, together with the kernel-side changes for client-side,
lets us finish the complete auth/assoc handshake with higher
rates than the mandatory ones, without any further config.
However, the downside to this is that a broken station that
doesn't check the basic rates are supported before it tries
to connect will possibly not get any response to its auth
frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a config option to allow setting a custom Basic NSS/MCS set. As a
default we use single stream HE-MCS 0-7.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Process HE information in (Re)Association Request frames and add HE
elements into (Re)Association Response frames when HE is enabled in the
BSS.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
The HE Capibilities element has dynamic size due to the variable length
and optional fields at the end. Mask out the channel width capabilities
that are less than the configured. Only add the MCS/NSS sets for the
announced channel widths and also add the PPET elements.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
This is used for both VHT and HE, so remove the misleading prefix.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
These are used for both VHT and HE, so remove the misleading prefix.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
These are used for both VHT and HE, so remove the misleading prefix.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Bandwidth is used for both VHT and HE here.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
oper_chwidth is used for both VHT and HE here.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
The bandwidth values are shared between VHT and HE mode so remove the
VHT specific prefix.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
These bits might be set by the capabilities read from the kernel, so
mask them out if beamforming is not enabled in the local configuration.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
This copying attempt was added incorrectly since that element is never
actually present in (Re)Association Request frames. It is only valid to
copy that element from the mesh peering frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
gcc 8.3.0 was apparently clever enough to optimize away the previously
used os_memset() to explicitly clear a stack buffer that contains keys
when that clearing happened just before returning from the function.
Since memset_s() is not exactly portable (or commonly available yet..),
use a less robust mechanism that is still pretty likely to prevent
current compilers from optimizing the explicit clearing of the memory
away.
Signed-off-by: Jouni Malinen <j@w1.fi>
The IE header length check was off-by-one and that could allow the loop
to read one octet beyond the end of the buffer before breaking out in
the second check.
Credit to OSS-Fuzz: https://bugs.chromium.org/p/oss-fuzz/issues/detail?id=14927
Fixes: 0a66ce3c49 ("WNM: Add support for SSID List element matching")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This AP behavior was missing from IEEE Std 802.11ai-2016, but it is
needed for the RSNE validation to work correctly and for a FILS STA to
be able to perform the mandatory check for RSNE matching when processing
the (Re)Association Response frame (as described in 802.11ai). REVmd
will be updating the standard to cover this AP case, so prepare the
implementation to match that. Without this, a FILS STA might reject
association whenever using FILS authentication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If none of the sr_control bits are set, we do not neet to add the IE to
the Beacon frame.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
While this should not happen in practical use cases,
wpa_get_ntp_timestamp() could return the same value when called twice in
a row quickly. Work around that case by enforcing a new Replay Counter
value based on stored last value.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds support to hostapd for configuring airtime policy settings for
stations as they connect to the access point. This is the userspace
component of the airtime policy enforcement system PoliFi described in
this paper: https://arxiv.org/abs/1902.03439
The Linux kernel part has been merged into mac80211 for the 5.1 dev
cycle.
The configuration mechanism has three modes: Static, dynamic and limit.
In static mode, weights can be set in the configuration file for
individual MAC addresses, which will be applied when the configured
stations connect.
In dynamic mode, weights are instead set per BSS, which will be scaled
by the number of active stations on that BSS, achieving the desired
aggregate weighing between the configured BSSes. Limit mode works like
dynamic mode, except that any BSS *not* marked as 'limited' is allowed
to exceed its configured share if a per-station fairness share would
assign more airtime to that BSS. See the paper for details on these
modes.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
This provides a mechanism for configuring per-STA airtime weight for
airtime policy configuration.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
This allows authenticator side to complete FT initial mobility domain
association using FT-EAP with PMKSA caching.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When completing FT initial mobility domain association with EAP, store
XXKey/MPMK in the PMKSA cache instead of MSK. The previously stored MSK
was of no use since it could not be used as the XXKey for another FT
initial mobility domain association using PMKSA caching.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It is apparently possible to somehow trigger the driver to report a
channel switch event during ACS operation when the interface information
is not yet complete. hapd->iface->current_mode could be NULL in that
case and that would result in process termination due to NULL pointer
dereference.
It should not really be possible to trigger a channel switch during ACS
is running (i.e., before the AP mode operation has been started), but
since that has been seen in an arbitrary test sequence with interface
start/stop operations with various parameters (both valid and invalid),
better prevent a crash here by ignoring the unexpected event instead of
trying to process it.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Unexpected CHAN_SWITCH command could get this function using a NULL
pointer if the channel switch was requested while the interface was
already disabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
driver->hapd_deinit() is going to free the memory that the cached
pointers are pointing to, so clear the pointers to avoid possibility of
dereferencing used memory. It seemed to be possible to hit a code path
using those fields by issuing a CHAN_SWITCH command on disabled hostapd
interface in some cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds a ieee80211ax=0/1 line to the STATUS output to indicate
the configuration of ieee80211ax, which similar to ieee80211n and
ieee80211ac.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The first four octets of the element were used as a host byte order u32.
That is not correct on bigendian CPUs, so handle byte swapping needs
properly. Mark the he_oper_params field as le32 to explicitly indicate
the byte order and swap the generated params content based on CPU byte
order.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The current code will always use the size required when all optional
elements are present. This will cause the Linux kernel to consider the
field to be malformed if the elements are not actually flagged as being
present.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
SPR allows us to detect OBSS overlaps and allows us to do adaptive CCA
thresholds. For this to work the AP needs to broadcast the element
first.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Properly populate the the HE Capabilities element with the info read
from the kernel.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
According to P802.11ax/D4.0 9.4.2.238 (HE Operation element) the BSS
Color Information field is located after the HE Operation Parameters
field. Fix the ordering of the bit masks/offsets for fields in these 3+1
octets used as a single 32-bit value. With these changes, Wireshark 3.2
is able to properly parse and display Beacon frames.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
IEEE P802.11ax/D4.0 9.4.2.243 "HE Operation element" indicates that the
special value 1023 in the TXOP Duration RTS Threshold field is used to
indicate that TXOP duration-based RTS is disabled. Use that value as the
default instead of the previously used value 0 which would really mean
threshold of 0 usec. Furthermore, the previous implementation did not
allow values larger than 255 to be used for this field while the field
is actually 10 bits in size.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
This makes it easier to upper layer components to manage operating
channels in cases where the same radio is shared for both station and AP
mode virtual interfaces.
Signed-off-by: Omer Dagan <omer.dagan@tandemg.com>
Logs involving IEEE 802.11 Status Codes output the Status Code value,
but do not provide any explanation of what the value means. This change
provides a terse explanation of each status code using the latter part
of the Status Code #define names.
Signed-off-by: Alex Khouderchah <akhouderchah@chromium.org>
The new hostapd configuration parameter dpp_controller can now be used
with the following subparameter values: ipaddr=<IP address>
pkhash=<hexdump>. This adds a new Controller into the configuration
(i.e., more than one can be configured) and all incoming DPP exchanges
that match the specified Controller public key hash are relayed to the
particular Controller.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not try to derive a PMK-R0 and PMK-R1 again for the case where an
association was started with FT protocol and PTK is rekeyed using 4-way
handshake. Instead, use the previously derived PMK-R1 to allow a new PTK
to be derived.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not try to derive a PMKID for EAPOL-key msg 1/4 when going through
4-way handshake to rekey PTK during an association that was started
through FT protocol.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed to allow PTK rekeying to be performed through 4-way
handshake in an association started through FT protocol.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed to avoid leaving some timers (e.g., for PTK rekeying)
running afrer a STA has disassociated.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
