The local ifindex list needs to be updated only if the current bridge
interface is the correct one. If hostapd is going to move the interface
to another bridge, the old bridge ifindex must not be added. In
addition, when removing the bridge interface on deinit, it may need to
be set down to allow bridge removal.
Signed-off-by: Jouni Malinen <j@w1.fi>
The interface was incorrectly changed to station mode between the two
IBSS join requests and that made the second attempt fail. Remove that
undesired mode clearing from this special case of IBSS leave sequence.
Signed-off-by: Jouni Malinen <j@w1.fi>
These hostapd configuration parameter was left at the default values
(WPA-PSK/TKIP) even for cases where WPA was disabled. While these
parameters are not really used much in non-WPA cases, they do get used
for one corner case in nl80211 configuration to disable encryption of
EAPOL frames in IEEE 802.1X WEP case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 9f12614b8c ('nl80211: Do not
encrypt IEEE 802.1X WEP EAPOL') tried to use
NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT to disable encryption of EAPOL
frames for WEP IEEE 802.1X. However, it used incorrect key management
suite (IEEE 802.1X with WPA/WPA2 while the non-WPA version is needed
here). Consequently, the no-encrypt flag was never set to the driver
(WPA/WPA2 cases do not meet the WEP as pairwise criteria).
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to wait for the timeout if the ROAM command itself
failed. This could happen if an earlier test case had left hidden SSIDs
in the cfg80211 BSS table.
Signed-off-by: Jouni Malinen <j@w1.fi>
Leaving hidden SSIDs in the cfg80211 BSS table can result in errors in
the following test cases, so use special care to clear all BSS entries
at the end of the wext_hidden test case.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows code coverage report to be generated must faster with the
help of parallel VMs executing test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit faf9a8585d added mechanism for
selecting 2.4 or 5 GHz band for scan operation. However, no mechanism
for setting the setband value was added at that time. This commit adds a
new SET ctrl_iface parameter to allow the setband functionality to be
used. "SET setband <AUTO/5G/2G>" can be used to select all bands, 5 GHz
band only, or 2.4 GHz band only.
Signed-off-by: Jouni Malinen <j@w1.fi>
Android framework maintains a state to process the scan results after
the scan is issued. If wpa_supplicant issues the scan during the
initialization, the one issued by the framework may fail (with EBUSY) if
the host driver is already processing the scan. Thus, the scan results
returned for the first scan triggered by wpa_supplicant are not
processed for getting displayed resulting in delay for the display of
the first scan results after the Wi-Fi subsystem initialization. Thus,
trigger the scan only based on the framework request on Android.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
FAIL-BUSY was already returned for the case where a scan had been
started, but with the radio work design, it would have been possible to
schedule multiple scan requests if a non-scan radio work was in
progress. Multiple back-to-back scans are not usually very helpful, so
reject this type of cases where the SCAN command would be used to build
such a sequence.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Makefile always installs to /usr/local/bin and on some platforms,
/usr/local/bin is not in default search path. Modify the Makefile such
that bin path can be configurable so that build system can pass
appropriate path for installation. If bin path is not specified then by
default binaries are installed in /usr/local/bin.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that offchannel TX (PD in this specific case) does not
stop ongoing long P2P_LISTEN operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
On receiving the cancel remain on channel event, the pending_tx
is scheduled immediately and returned. This was preventing
the wpas_p2p_listen_start function from execution thereby resulting
in termination of the long listen operation.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
There were couple of typos in the IP addresses and there was no coverage
for the normal unicast ARP response from the bridge (since non-wireless
device does not get proxied by the AP). In addition, it is better to
change the IP address used here to be unique to make the sniffer logs
easier to interpret.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds transmission of number of NS/NA frames to test ProxyARP
behavior. The actual validation of the AP behavior is still manual,
i.e., a separate inspectation of the capture files is needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This may be needed in some corner cases where broadcast frames with two
associated stations are received by both devices.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The final invitation case in this test was verified incorrectly. The GO
was already operatign in that case, so there was not supposed to be a
new P2P-GROUP-STARTED message from GO. That happened to be show up in
the pending event messages from the last instance, but that was just by
accident and any additional dump_monitor() operation added here would
cause this test to fail. Fix this by handling the final invitation
separately and verifying that only the client side indicates
P2P-GROUP-STARTED.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for WpaSupplicant instance to be used without the global
control socket, so allow dump_monitor() to handle this case cleanly.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
