Commit graph

112 commits

Author SHA1 Message Date
Arik Nemtsov
4f73d88afa Maintain internal copy of Probe Response offload capabilities
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2011-12-10 21:11:32 +02:00
Szymon Bigos
9337e876ab Fix generated WPS PIN values to use zero-padding
The dynamically generated PINs are supposed to have 8 digits, but
some PIN generatation cases were not zero-padding these properly.
2011-12-02 23:04:39 +02:00
Jouni Malinen
c0f83f3104 WPS: Disable WPS(v2) in WPA/TKIP-only configuration
When using wpa_supplicant AP mode, WPS support is enabled by default for
WPA/WPA2-Personal. Change this to enforce the WPS2 rules on not allowing
WPS to be used with WPA/TKIP-only configuration (i.e., at minimum, mixed
mode with WPA/TKIP and WPA2/CCMP has to be used for WPS to be enabled).

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-12-01 21:46:19 +02:00
Arik Nemtsov
79b8c60f81 Set ht_capab from based on driver capabilities when in P2P GO mode
Set the HT capabilities of a P2P GO according to the wiphy supported
ones. Mask-in a white-list of HT capabilities that won't cause problems
for non-supporting stations.

Signed-hostap: Arik Nemtsov <arik@wizery.com>
2011-11-29 23:45:07 +02:00
Dmitry Shmidt
8a5e75f60f P2P: Send STA connected/disconnected events to parent ctrl_iface
Send the connection events from P2P group to both the group interface
and parent interface ctrl_ifaces to make it easier for external monitor
programs to see these events without having to listen to all group
interfaces when virtual group interfaces are used.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2011-11-25 23:56:13 +02:00
Johannes Berg
dd840f793c AP: Add explicit EAPOL TX status event
The new event can be used when EAPOL TX status can't be reported as a
complete 802.11 frame but is instead reported as just the EAPOL data as
originally passed to hapd_send_eapol().

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2011-11-19 13:00:30 +02:00
Vasanthakumar Thiagarajan
0399f2e4e5 wpa_supplicant: Set configured auth_algs for AP mode
In AP mode, authentication algorithm is reset in
hostapd_config_defaults_bss() and never set to the configured one. This
would pass the default auth_algs (OPEN|SHARED) to driver regardless of
what the wpa_supplicant configuration is requesting.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
2011-11-16 16:30:36 +02:00
Jouni Malinen
04ed4e984e AP: Only enable WPS for open and WPA/WPA2-Personal configuration
When wpa_supplicant AP mode is used, WPS was enabled by default
regardless of security mode. This is not desired for WEP, so change
the AP configuration to enable WPS only for open and WPA/WPA2-Personal
networks.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-14 16:16:29 +02:00
Jouni Malinen
a17539ebcd Remove unnecessary include file inclusion
Signed-hostap: Jouni Malinen <j@w1.fi>
2011-11-13 22:13:04 +02:00
Christian Lamparter
6bf731e8ce wpa_supplicant: Unify hardware feature data
The hardware feature data is required in several different places
throughout the code. Previously, the data was acquired and freed on
demand, but with this patch wpa_supplicant will keep a single copy
around at runtime for everyone to use.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2011-10-23 17:21:50 +03:00
Johannes Berg
9b90955ec7 AP: Pass only bssid/addr/wds to EVENT_RX_FROM_UNKNOWN 2011-10-20 21:51:32 +03:00
Johannes Berg
bcf24348ed AP: Do station poll in driver wrapper
This offloads the station polling to driver wrappers, which may offload
it again to the driver. The hostap driver wrapper uses "real" data
frames while nl80211 uses null data frames.

Also add a specific event to indicate that a poll was successful for
future use with the nl80211 driver.
2011-10-20 21:03:08 +03:00
Jouni Malinen
3c11382b6c Remove set_intra_bss() driver_ops
This has been replaced by the isolate parameter available through
set_ap() calls.
2011-10-17 23:04:27 +03:00
Janusz Dziedzic
a57db49c32 wpa_supplicant: AP mode, set drv_flags
In AP/P2P_GO mode we should have correct hostapd drv_flags.
2011-09-22 01:05:01 +03:00
Jouni Malinen
6bcb1c2ba5 wpa_supplicant AP: Set static WEP keys if configured
This is needed to configure static WEP keys to the driver through the
hostapd configuration structures.
2011-09-15 15:04:46 +03:00
Jouni Malinen
697cd03fc2 AP: Set pairwise/group cipher for non-WPA modes
This is needed to avoid confusing configuration in some nl80211
drivers that the new AP mode configuration alternatives for
setting security policy.
2011-09-15 15:02:59 +03:00
Jouni Malinen
64fa840a97 nl80211: Fix WPA_VERSIONS attribute for Connect command
The previous code was trying to figure out which WPA version is
used based on the extra IEs requested for Association Request. That
did not work properly in cases where non-WPA networks are used with
some extra IEs. Fix this by using more robust mechanism for passing
the WPA versions from core wpa_supplicant to the driver_ops
associate().
2011-09-02 20:40:23 +03:00
Eliad Peller
d26e45a44a wpa_supplicant AP: Enable uapsd in P2P GO mode if go_apsd was set
If uapsd is explicitly enabled, set conf->bss->wmm_enabled and
conf->bss->wmm_uapsd to enable (and advertise) uapsd.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2011-08-06 22:08:38 +03:00
Jouni Malinen
04a85e4401 P2P: Filter Probe Request frames based on DA and BSSID in Listen state
Only accept Probe Request frames that have a Wildcard BSSID and a
destination address that matches with our P2P Device Address or is the
broadcast address per P2P specification 3.1.2.1.1.
2011-07-15 20:28:46 +03:00
Johannes Berg
6cd930cb3c P2P: Fix p2p_intra_bss with nl80211
The current implementation of p2p_intra_bss doesn't work since the flag
isn't propagated into the corresponding hostapd config, so AP code will
never enable AP isolation and will in fact disable it again after it had
been enabled by the P2P code.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-07-15 17:13:44 +03:00
Angie Chinchilla
2db9174503 wpa_s AP mode: Enable HT20 if driver supports it
If the driver supports HT20, set the config parameter ieee80211n
to enable it. This does not enable HT40.

Signed-off-by: Angie Chinchilla <angie.v.chinchilla@intel.com>
2011-07-05 16:49:28 +03:00
Jouni Malinen
ca62e114aa wpa_supplicant AP: Disable AP mode on disassoc paths
Regardless of how the AP mode is disabled, wpa_supplicant_ap_deinit()
must be called. Make sure this happens on all paths by calling the
deinit function from wpa_supplicant_mark_disassoc().
2011-07-05 16:38:30 +03:00
Jean-Michel.Bachot
8be6450cb6 P2P: Fix WpsFailed signal in P2P D-Bus
Fix a NULL pointer dereference in commit
3734552f15 in the case of PBC overlap and
timeout case.

Signed-off-by: Jean-Michel.Bachot <jean-michelx.bachot@intel.com>
Signed-off-by: Jayant Sane <jayant.sane@intel.com>
Signed-off-by: Angie Chinchilla <angie.v.chinchilla@intel.com>
2011-06-25 15:29:31 +03:00
Jayant Sane
3734552f15 P2P: Add WpsFailed signal in P2P D-Bus
Signal is triggered if an error occurs during WPS provisioning phase.

Signed-off-by: Jean-Michel.Bachot <jean-michelx.bachot@intel.com>
Signed-off-by: Jayant Sane <jayant.sane@intel.com>
2011-06-25 11:47:04 +03:00
Jouni Malinen
e73edcaa6a wpa_s AP mode: Fix regression in P2P AP mode setup
Commit c76e5d7f9b moved the
ap_configured_cb() call into a completion callback from AP mode code.
However, this callback can be called before hostap_setup_interface()
returns. In that case, the ap_configured_cb() ended up getting
called before the wpa_supplicant connection information was updated.
Fix this by reordering code to set up everything before calling
hostapd_setup_interface().
2011-04-04 12:50:26 +03:00
Johannes Berg
c76e5d7f9b wpa_s AP mode: complete only when setup is complete
The AP code might, currently only in the case of HT40, defer actual
enabling to after a scan. In this case, the wpa_s AP code gets confused.
Add a callback for it to use and make it use it to finish only when the
setup has actually completed.

With appropriate hacks in place this allows using HT40 in P2P mode.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-03-19 13:11:15 +02:00
Johannes Berg
2f646b6e83 WPS: Store (secondary) device type as binary
Instead of converting back and forth from the string representation,
always use the binary representation internally.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-03-17 18:50:22 +02:00
Johannes Berg
d8a43924ec wpa_s AP mode: Add notification functions for STA authorized
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-03-16 15:58:41 +02:00
Jouni Malinen
ab45223b1a wpa_supplicant AP: Copy generated UUID for AP configuration
If the wpa_supplicant configuration file does not specify an UUID,
we need to copy the generated UUID, not the all zeros buffer
reserved for the configured UUID.
2011-03-10 18:40:16 +02:00
Jouni Malinen
d601247ca9 P2P: Allow WPS_PBC command on GO to select on P2P Device Address
An optional parameter, p2p_dev_addr, can now be given to WPS_PBC
command on P2P GO to indicate that only the P2P device with the
specified P2P Device Address is allowed to connect using PBC. If
any other device tries to use PBC, a session overlap is indicated
and the negotiation is rejected with M2D. The command format for
specifying the address is "WPS_PBC p2p_dev_addr=<address>", e.g.,
WPS_PBC p2p_dev_addr=02:03:04:05:06:07

In addition, show the PBC session overlap indication as a WPS failure
event on an AP/GO interface. This particular new case shows up as
"WPS-FAIL msg=4 config_error=12".
2011-02-07 18:28:36 +02:00
Johannes Berg
0d7e5a3a29 Allow AP mode to disconnect STAs based on low ACK condition
The nl80211 driver can report low ACK condition (in fact it reports
complete loss right now only). Use that, along with a config option, to
disconnect stations when the data connection is not working properly,
e.g., due to the STA having went outside the range of the AP. This is
disabled by default and can be enabled with disassoc_low_ack=1 in
hostapd or wpa_supplicant configuration file.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2010-12-28 17:15:01 +02:00
Jouni Malinen
0fe620de7e Fix CONFIG_AP=y build without CONFIG_WPS=y 2010-11-25 23:34:56 +02:00
Jouni Malinen
3c85f144ce P2P: Fix Action frame sending after disconnection
assoc_freq needs to be cleared when an interface gets disconnected.
This fixes an issue where P2P Action frame transmission may fail
because of missing remain-on-channel operation when using the same
interface for group operations (or non-P2P connections) and P2P
management operations.
2010-11-25 16:04:07 +02:00
Jouni Malinen
fe99fb74f1 Fix wpa_supplicant AP mode build after hostapd changes 2010-11-24 16:52:04 +02:00
Jouni Malinen
ca806fb540 P2P: Indicate WPS events from AP mode only during group formation
The duplicated WPS event in the parent interface should only be used
during P2P group formation, i.e., when the WPS operation was actually
started using the parent interface. When authorizing a client to
connect to an already running group, the WPS command is issued on
the group interface and there is no need to duplicate the event to
the parent interface.
2010-11-18 12:42:02 +02:00
Jouni Malinen
9dd7d6b09c WPS: Add special AP Setup Locked mode to allow read only ER
ap_setup_locked=2 can now be used to enable a special mode where
WPS ER can learn the current AP settings, but cannot change then.
In other words, the protocol is allowed to continue past M2, but
is stopped at M7 when AP is in this mode. WPS IE does not
advertise AP Setup Locked in this case to avoid interoperability
issues.

In wpa_supplicant, use ap_setup_locked=2 by default. Since the AP PIN
is disabled by default, this does not enable any new functionality
automatically. To allow the read-only ER to go through the protocol,
wps_ap_pin command needs to be used to enable the AP PIN.
2010-11-17 16:48:39 +02:00
Jouni Malinen
70d84f11fe WPS: Add wps_ap_pin ctrl_iface command for wpa_supplicant AP mode
This can be used to control the AP PIN in wpa_supplicant AP mode
in the same way as the identical command in hostapd ctrl_iface.
2010-11-17 16:46:55 +02:00
Jouni Malinen
de979d8fc7 Fix max_stations to apply to associated STAs, not P2P peers
This driver capability limit was supposed to indicate limit on
how many stations can associate with us in the AP mode, not how
many P2P peers are stored in the peer table.
2010-10-19 17:17:04 +03:00
Jouni Malinen
dae608d5d3 Add max_num_sta config option for wpa_supplicant AP mode
This can be used to limit the number of stations allowed to be
connected to the AP.
2010-10-19 17:08:20 +03:00
Anil Gathala Sudha
a0dee79709 P2P: Send AP mode WPS-FAIL event to parent interface
The AP operation with wpa_supplicant requires an additional callback
to get the needed event information from hostapd side so that
wpa_msg() can be called for wpa_s->parent if needed.
2010-10-14 20:57:00 +03:00
Sudhakar Swaminathan
0f66abd25b P2P: Add option for disabling intra BSS distribution
p2p_intra_bss configuration parameter can now be used to
disable/enable intra BSS distribution (bridging of frames between
the clients in a group).
2010-09-10 10:30:26 -07:00
Ardong Chen
2f9929ffcc WPS: Allow pending WPS operation to be cancelled
A new ctrl_interface command, WPS_CANCEL, can now be used to cancel
a pending or ongoing WPS operation. For now, this is only available
with wpa_supplicant (either in station or AP mode). Similar
functionality should be added for hostapd, too.
2010-09-10 10:30:25 -07:00
Jouni Malinen
56815b2b7d Copy WPS strings into AP configuration when using wpa_supplicant AP 2010-09-09 07:17:21 -07:00
Jouni Malinen
0e14267a31 P2P: Avoid segfault on AP deinit after failed AP start 2010-09-09 07:17:21 -07:00
Jouni Malinen
f80a2237ca Fix AP mode wps_pin command to return the entered PIN
This command is supposed to return the PIN value that was generated
or passed in as an argument. In the AP case, the entered PIN was not
being returned.
2010-09-09 07:17:21 -07:00
Jouni Malinen
eea2fd9eff P2P: Add mechanism for configuring UAPSD parameters for group
This is needed to be able to change parameters for dynamically
created interfaces between the creation of the interface and
association/start AP commands.

Following ctrl_interface commands can now be used:

P2P_SET client_apsd disable
- disable configuration (i.e., use driver default) in client mode

P2P_SET client_apsd <BE>,<BK>,<VI>,<VO>;<max SP Length>
- enable UASPD with specific trigger configuration (0/1) per AC
  (max SP Length is currently ignored)

P2P_SET go_apsd disable
- disable configuration (i.e., use driver default) in AP mode

P2P_SET go_apsd <0/1>
- disable/enable APSD in AP mode
2010-09-09 07:17:21 -07:00
Jouni Malinen
d9d6a58c8f P2P: Fix invitation to active group to use correct operating channel
Invitation Request must use the current operating frequency of the
group, not the default operating channel.
2010-09-09 07:17:20 -07:00
Jouni Malinen
6e3f4b89ea P2P: Let the driver wrapper know if association is for P2P group 2010-09-09 07:17:17 -07:00
Jouni Malinen
e44f8bf20a P2P: Add P2P configuration and callbacks in hostapd code 2010-09-09 07:17:17 -07:00
Jouni Malinen
b22128efdc P2P: Add initial version of P2P Module 2010-09-09 07:17:17 -07:00