The scan results from old test cases showing different SSID on the AP
can result in false failures, so avoid those by ignoring old scan
results from cfg80211.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
All P2P use cases are required to use the global operating table and
there is no need to need to try to maintain some backwards compatibility
with country code -specific values. Clean up the implementation by
removing the unnecessary country parameter.
Signed-hostap: Jouni Malinen <j@w1.fi>
Reset ft_completed if STA receives deauthentication
between FT reassoc success and the subsequent initial
mobility authentication and association.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit fb8984fd6f added a mechanism to
skip the Listen state when the peer is expected to be waiting for us to
initiate a new GO Negotiation. However, this flag was set when building
the GO Negotiation Response frame with status 1 regardless of whether we
managed to send that frame or peer receive it. This could result in GO
Negotiation failures in cases where the peer did not receive the
response and Listen channels of the devices were different. Fix this by
setting the flag only after TX status indicating success has been
received.
This fixes frequent failures shown for the test_grpform_pbc hwsim test
case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
We should not call getSessionID method if it's not provided. This fixes
a regression from commit 950c563076 where
EAP methods that did not implement getSessionId resulted in NULL pointer
dereference when deriving the key.
Signed-off-by: Shijie Zhang <shijiez@qca.qualcomm.com>
Previously, only explicit indications of authentication failures were
used to disable a network block temporarily. Extend this to use multiple
failed connection attempts as a sign of a possible authentication or
authorization failure to reduce the frequency of connection attempts
with a network that does not seem to allow connection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When Action frame TX is postponed until a pending p2p_scan completes,
there may be additional operations that need to be continued after the
postponed Action frame TX operation completes. Fix this by starting
pending operation (if any) from TX status event for after_scan_tx
frames.
This fixes common errors seen with the test_discovery hwsim test case.
Signed-hostap: Jouni Malinen <j@w1.fi>
The fast-connect optimization to skip a new scan did not update how the
RSN preauthentication callback is used. There is no point in trying to
add preauthentication candidates from cases where scan was skipped, so
skip this call, too, in such cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
All wpa_supplicant_deinit_iface() callers ended up freeing wpa_s
immediately after this call. Move os_free(wpa_s) into the deinit
function to share the same call and make the deinit sequence clearer.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add "EAPLogoff" and "EAPLogon" interface DBus commands which
parallel the "logoff" and "logon" wpa_ctrl commands which terminate
and restart EAP authentication. Slightly enhance the "logon" case
by expiring any running "startWhile" timer.
Signed-hostap: Paul Stewart <pstew@chromium.org>
In order to test clients in scenarios where APs may (randomly)
drop certain management frames, introduce some testing options
into the hostapd configuration that can make it ignore certain
frames. For now, these are probe requests, authentication and
(re)association frames.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This option can be used only for global parameters that are not going
to be changed from settings.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Iliyan Malchev <malchev@google.com>
Dmitry reported that the kernel could no longer parse the
scheduled scan attributes correctly after my patch to use
nla_nest_start/nla_nest_end. The reason is that the wrong
attribute is closed I accidentally made it close the full
scan config instead of just the SSID match set.
Reported-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Add "get_capability freq" command to print a more verbose list of
channels and frequencies in MHz. The tag "NO_IBSS" is added, if IBSS
mode is not allowed on a channel. This allows userspace programs to get
the frequencies and limitations associated with each channel.
This extends the information already provided in "get_capability
channels" but a new interface is chosen because of backwards
compatibility considerations.
Signed-hostap: Bruno Randolf <br1@einfach.org>
Harmonize EAP status events over control interface to provide same
functionality as existing D-Bus callback.
Signed-hostap: Chris Hessing <chris.hessing@cloudpath.net>
TK was incorrectly truncated in a way that resulted in CCMP (128-bit
key) encryption being used in practice.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A kernel commit ("mac80211: fix FT roaming") started validating that the
STA entry is marked associated when adding a key. While this is needed
to fix some FT use cases with hardware crypto, it has a side effect of
breaking TDLS key configuration. Work around this by trying to
re-configure the key for the direct link after the STA entry has been
set with all information. In addition, try to tear down the link if
anything goes wrong in key configuration (if both attempts fail) or
enabling the link in the driver.
Signed-hostap: Jouni Malinen <j@w1.fi>
"WPS_NFC_CONFIG_TOKEN <WPS/NDEF> <network id>" can now be used to build
an NFC configuration token from a locally configured network.
Signed-hostap: Jouni Malinen <j@w1.fi>
This extends the WPS ER commands that previously accepted only UUID as
an identifier for an AP to use either UUID or BSSID for this.
Signed-hostap: Jouni Malinen <j@w1.fi>
wps_build_public_key() takes the dh_ctx into use and another attempt to
use the same DH keys fails with wps->dh_ctx being set to NULL. Avoid
this by using the DH parameters only if dh_ctx is valid. This fixes
cases where a use of local pre-configured DH keys followed by an
operating using peer DH keys would faild due to unexpected attempt to
use local keys again.
Signed-hostap: Jouni Malinen <j@w1.fi>
There may be cases where multiple BSS entries for a single BSSID are in
the table. This is mostly in automated test cases due to the AP
configuration changes, but something similar could potentially happen as
a corner case in more realistic networks, too, e.g., when an AP changes
its operating channel. Make network selection more robust by trying to
find the exact BSS entry instead of any BSS entry with a matching BSSID
when storing GAS/ANQP response.
Signed-hostap: Jouni Malinen <j@w1.fi>
Stopping the AP first was not ideal for the test cases since it could
result in wpa_supplicant trying to connect back and start a scan at the
end of a test case and cause problems for the following test case that
tried to scan in the beginning while the previously started scan was
still in progress.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some extended capabilities (I'm currently interested in "Operating Mode
Notification" for VHT) are implemented by the kernel driver and exported
in nl80211. Use these in hostapd/wpa_supplicant.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This is mainly for testing purposes where it is convenient to have an
easy way of getting wpa_supplicant state cleared between test cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
If WPS provisioning step is completed with an AP that is in WPS
configured state, we can skip a second scan after the provisioning step
since the AP is unlikely to change its configuration in such a case.
This can speed up WPS connection a bit by removing an unneeded scan.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
Do not print the potentially long list of passed test cases. In case of
failure(s), make sure the failed test list is the last item in the
report.
Signed-hostap: Jouni Malinen <j@w1.fi>
The WPS tests are more prone to fail if scan results from the previous
test cases are allowed to remain in the wpa_supplicant BSS table during
the consecutive test since the test setup uses the same BSSID for the
test APs that change their configuration. Avoid these mostly bogus
issues by enforcing wpa_supplicant to drop and ignore old scan results
during the WPS test cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to configure wpa_supplicant to ignore old scan results
from the driver cache in cases where such results were not updated after
the scan trigger from wpa_supplicant. This can be useful in some cases
where the driver may cache information for a significant time and the AP
configuration is changing. Many such cases are for testing scripts, but
this could potentially be useful for some WPS use cases, too.
Signed-hostap: Jouni Malinen <j@w1.fi>
The after_wps counter could have potentially be left in its old non-zero
value in some WPS sequences which could result in a single-channel scan
being used based on obsolete information. Clear after_wps in
wpas_wps_reassoc() to make sure this does not happen.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the AP (P2P GO) has changes its channel of SSID recently, the BSS
table may have multiple entries for a BSSID. Select the one which was
most recently updated for WPS/P2P operations in such case to increase
the likelihood of using current information.
Signed-hostap: Jouni Malinen <j@w1.fi>
This removes the unnecessary separation of P2P (no hostapd) and AP
tests. The same scripts can be used to prepare for these tests and to
execute the tests.
Signed-hostap: Jouni Malinen <j@w1.fi>
