IEEE Std 802.11-2020 mandates H2E to be used whenever an SAE password
identifier is used. While this was already covered in the
implementation, the sae_prepare_commit() function still included an
argument for specifying the password identifier since that was used in
an old test vector. Now that that test vector has been updated, there is
no more need for this argument anymore. Simplify the older non-H2E case
to not pass through a pointer to the (not really used) password
identifier.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do so for both wpa_supplicant and hostapd. While this was not explicitly
required in IEEE P802.11az/D3.0, likely direction for the draft is to
start requiring use of H2E for all cases where SAE is used with PASN.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When a PTK derivation is done as part of PASN authentication flow, a KDK
derivation should be done if and only if the higher layer protocol is
supported by both parties.
Fix the code accordingly, so KDK would be derived if and only if both
sides support Secure LTF.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reuse the SAE anti-clogging token implementation to support similar
design with the PASN comeback cookie.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When a Deauthentication frame is received, clear the corresponding PTKSA
cache entry for the given station, to invalidate previous PTK
information.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The anti-clogging code was under CONFIG_SAE. Change this so it can be
used both with CONFIG_SAE and CONFIG_PASN.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
PASN authentication mandates support for comeback flow, which
among others can be used for anti-clogging purposes.
As the SAE support for anti clogging can also be used for PASN,
start modifying the source code so the anti clogging support
can be used for both SAE and PASN.
As a start, rename some variables/functions etc. so that they would not
be SAE specific. The configuration variable is also renamed, but the old
version remains available for backwards compatibility.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
For testing purposes, add support for corrupting the MIC in PASN
Authentication frames for both wpa_supplicant and hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When a public key is included in the PASN Parameters element, it should
be encoded using the RFC 5480 conventions, and thus the first octet of
the Ephemeral Public Key field should indicate whether the public key is
compressed and the actual key part starts from the second octet.
Fix the implementation to properly adhere to the convention
requirements for both wpa_supplicant and hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
As defined in IEEE P802.11az/D3.0, 12.12.3.2 for the second PASN frame.
This was previously covered only for the case when the explicit PMKSA
was provided to the helper function. Extend that to cover the PMKID from
SAE/FILS authentication cases.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
There is no point in trying to build in rest of this function if in the
middle of it the CONFIG_NO_RADIUS case would unconditionally fail.
Simply make all of this be conditional on that build parameter not being
set to make things easier for static analyzers.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reordering of code in handle_auth_cb() when adding support for full
station state messaged up frame length checks. The length was originally
tested before looking at the payload of the frame and that is obviously
the correct location for that check. The location after those full state
state changes was after having read six octets of the payload which did
not help at all since there was no addition accesses to the payload
after that check.
Move the payload length check to appropriate place to get this extra
level of protection behaving in the expected manner. Since this is a TX
status callback handler, the frame payload is from a locally generated
Authentication frame and as such, it will be long enough to include
these fields in production use cases. Anyway, better keep this check in
working condition.
Fixes: bb598c3bdd ("AP: Add support for full station state")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
hostapd_get_oper_chwidth(iconf) instead of direct access to
iface->conf->vht_oper_chwidth is needed here to be able to use this with
HE in cases where VHT is not enabled.
Signed-off-by: Shay Bar <shay.bar@celeno.com>
According to latest IEEE 802.11 standard, Transmit Power Envelope
element is also relevant to IEEE 802.11ax and is no longer called VHT
Transmit Power Envelope. Remove the VHT naming from the element and move
hostapd_eid_txpower_envelope() from ieee802_11_vht.c to ieee802_11.c in
preparation of using it with HE.
Signed-off-by: Shay Bar <shay.bar@celeno.com>
The new status code values for SAE H2E and PK resulted in the
sta->added_unassoc cases incorrectly removing the STA entry after
successful SAE commit messages. Fix this by using sae_status_success()
instead of direct check for WLAN_STATUS_SUCCESS when processing SAE
commit messages before removing station entry.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
In some contexts (e.g., Multi-AP) it can be useful to have access to
some of the management frames in upper layers (e.g., to be able to
process the content of association requests externally).
Add 'notify_mgmt_frames'. When enabled, it will notify the ctrl_iface
when a management frame arrives using the AP-MGMT-FRAME-RECEIVED event
message.
Note that to avoid completely flooding the ctrl_iface, not all
management frames are included (e.g., Beacon and Probe Request frames
are excluded).
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
IEEE P802.11az/D2.6 added definitions to include RSNXE in the PASN
negotiation. Implement the new functionality in both wpa_supplicant and
hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Note that the implementation is not complete as it is missing support
for the FT wrapped data which is optional for the station, but must be
supported by the AP in case the station included it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
As the PASN FILS authentication is only defined for FILS SK without PFS,
and to support PASN authentication with FILS, implement the PASN with
FILS processing as part of the PASN handling and not as part of the WPA
Authenticator state machine.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add the ability to disable HT/VHT/HE for specific BSS from hostapd.conf.
- Add disable_11ax boolean to hostapd_bss_config.
- Change disable_11n and disable_11ac to bool in hostapd_bss_config.
- Add configuration option to set these disable_11* parameters
(which were previously used only automatically based on incompatible
security parameters to disable HT/VHT).
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Make sae_status_success() more explicit by rejecting SAE-PK status code
when the AP is not configured with PK.
Fixes: 20ccf97b3d ("SAE-PK: AP functionality")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When testing SAE reflection, the incoming commit may have the H2E status
code (126) or SAE-PK (127), but the test code in the AP was always
sending back status code 0. The STA would then reject the commit
response due to expecting H2E/SAE-PK status code.
Just reflect the incoming status code so the commit can be rejected
based on the SAE contents regardless of which variant of SAE was used.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Some legacy stations copy previously reserved RSN capability bits,
including OCVC, in (Re)Association Request frames from the AP's RSNE but
do not indicate MFP capability and/or do not send OCI in RSN handshakes.
This is causing connection failures with such erroneous STAs.
To improve interoperability with such legacy STAs allow a workaround OCV
mode to be enabled to ignore OCVC=1 from the STA if it does not follow
OCV requirements in the first protected exchange. This covers cases
where a STA claims to have OCV capability, but it does not negotiate use
of management frame protection or does not include OCI in EAPOL Key msg
2/4, FT Reassociation Request frame, or FILS (Re)Association Reqest.
The previous behavior with ocv=1 is maintained, i.e., misbehaving STAs
are not allowed to connect. When the new workaround mode is enabled with
ocv=2, the AP considers STA as OCV capable on below criteria
- STA indicates both OCV and MFP capability
- STA sends OCI during connection attempt in a protected frame
Enabling this workaround mode reduced OCV protection to some extend
since it allows misbehavior to go through. As such, this should be
enabled only if interoperability with misbehaving STAs is needed.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Initiate SA Query for a WPS+MFP AP. STA flag checks for MFP added for
Association Request frames that use WPS IE without RSNE. This is needed
to avoid giving an opportunity to skip the protection against
disconnections when WPS is enabled.
Signed-off-by: Disha Das <dishad@codeaurora.org>
Resolved the below warning
../src/ap/ieee802_11.c:4535:25: warning: 'reply_res' may be used
uninitialized in this function [-Wmaybe-uninitialized]
if (sta && ((reply_res != WLAN_STATUS_SUCCESS &&
^
Since reply_res is been assigned inside an if condition and so
compiler treats reply_res as uninitalized variable
Initialize reply_res with WLAN_STATUS_UNSPECIFIED_FAILURE.
Fixes: 5344af7d22 ("FT: Discard ReassocReq with mismatching RSNXE Used value")
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
The AP mode condition for initiating the SA Query procedure when
receiving a new (Re)Association Request frame used only association
state and MFP negotiation result without checking that the key exchange
has been completed. This can give rise to a corner case where the SA
Query procedure may get started after open association but before the
4-way handshake has been completed, resulting in open SA query frames
over the air.
Fix this by adding station authorized check in hostapd_notif_assoc() and
check_assoc_ies().
Signed-off-by: Rohan <drohan@codeaurora.org>
Enhance the return values of ocv_verify_tx_params with enum to indicate
different OCI verification failures to caller.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
As per RFC 8110 (Opportunistic Wireless Encryption), if the AP has the
PMK identified by the PMKID and wishes to perform PMK caching, it will
include the PMKID in the Association Response frame RSNE but does not
include the Diffie-Hellman Parameter element.
This was already addressed for most cases with owe_process_assoc_req()
not setting sta->owe_ecdh in case PMKSA caching is used. However, it was
possible to an old STA entry to maintain the initial sta->owe_ecdh value
if reassociation back to the same AP was used to initiate the PMKSA
caching attempt. Cover that case by adding an explicit check for the
time when the Association Response frame is being generated.
Signed-off-by: Chittur Subramanian Raman <craman@maxlinear.com>
Modify the check for VHT to include an option for HE in
hostapd_eid_wb_chsw_wrapper() and its callers to allow the Channel
Switch Wrapper element with the Wide Bandwidth Channel Switch subelement
to be included in Beacon and Probe Response frames when AP is operating
in HE mode without VHT.
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
Move hostapd_eid_wb_chsw_wrapper() from VHT specific ieee802_11_vht.c to
ieee802_11.c since this can be used for both HE and VHT. This commit
does not change any functionality to enable the HE use case, i.e., the
function is just moved as-is.
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
Operation in the 6 GHz band mandates valid HE capabilities element in
station negotiation. Reject association request upon receiving invalid
or missing HE elements.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
This was clarified in the draft specification to not be a mandatory
requirement for the AP and STA to enforce, i.e., matching security level
is a recommendation for AP configuration rather than a protocol
requirement.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new sae_commit_status and sae_pk_omit configuration parameters and
an extra key at the end of sae_password pk argument can be used to
override SAE-PK behavior for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This maintains knowledge of whether H2E or PK was used as part of the
SAE authentication beyond the removal of temporary state needed during
that authentication. This makes it easier to use information about which
kind of SAE authentication was used at higher layer functionality.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds AP side functionality for SAE-PK. The new sae_password
configuration parameters can now be used to enable SAE-PK mode whenever
SAE is enabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds core SAE functionality for a new mode of using SAE with a
specially constructed password that contains a fingerprint for an AP
public key and that public key being used to validate an additional
signature in SAE confirm from the AP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the OCV-FAILURE control interface event to notify upper layers of
OCV validation issues in FT and FILS (Re)Association Request frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make reporting of OCV validation failure reasons more flexible by
removing the fixed prefix from ocv_verify_tx_params() output in
ocv_errorstr so that the caller can use whatever prefix or encapsulation
that is most appropriate for each case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process HE 6 GHz band capabilities in (Re)Association Request frames and
pass the information to the driver.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Construct HE 6 GHz Band Capabilities element (IEEE 802.11ax/D6.0,
9.4.2.261) from HT and VHT capabilities and add it to Beacon, Probe
Response, and (Re)Association Response frames when operating on the 6
GHz band.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
It is possible for drivers to report received Management frames while AP
is going through initial setup (e.g., during ACS or DFS CAC). hostapd
and the driver is not yet ready for actually sending out responses to
such frames at this point and as such, it is better to explicitly ignore
such received frames rather than try to process them and have the
response (e.g., a Probe Response frame) getting dropped by the driver as
an invalid or getting out with some incorrect information.
Signed-off-by: Jouni Malinen <j@w1.fi>
"SET dpp_version_override <ver>" can now be used to request
wpa_supplicant and hostapd to support a subset of DPP versions. In
practice, the only valid case for now is to fall back from DPP version 2
support to version 1 in builds that include CONFIG_DPP2=y.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Discard the FT Reassociation Request frame instead of rejecting it
(i.e., do not send Reassociation Response frame) if RSNXE Used is
indicated in FTE, but no RSNXE is included even though the AP is
advertising RSNXE.
While there is not really much of a difference between discarding and
rejecting the frame, this discarding behavior is what the standard says
for this type of an error case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Allow STA entry to be removed and re-added to the driver with PMF is
used with FT. Previously, this case resulted in cfg80211 rejecting STA
entry update after successful FT protocol use if the association had not
been dropped and it could not be dropped for the PMF case in
handle_auth().
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter dpp_pfs can be used to specify
how PFS is applied to associations. The default behavior (dpp_pfs=0)
remains same as it was previously, i.e., allow the station to decide
whether to use PFS. PFS use can now be required (dpp_pfs=1) or rejected
(dpp_pfs=2).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
