Based on Jouni Malinen's [76055b4c6 "tests: D-Bus Get/Set Pmf"], modified
to use the correct "s" signature for the "Pmf" property.
Removed the negative test cases, because the synthesized property doens't
seem to do error checking upon being set.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
The hwsim's start.sh script spawns hostapd process using "sudo".
Since sudo forks a child process, $! holds the pid of sudo itself.
Fix that by storing the PID of the child process instead.
Since in VM "sudo" is replaced with a dummy script, pass an additional
argument to run-all.sh and start.sh scripts to indicate that they are
running inside a VM.
This is needed to fix ap_config_reload and ap_config_reload_file test
cases on some platforms where sudo is apparently not relaying the
signals properly.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In ap_acl_deny test, the AP doesn't send probe responses during scan due
to ACL reject. As the result, dev[0] might miss the AP's Beacon frame
because the dwell time is too short. Make the test more robust and
trigger passive scan, and by that increase the probability of hearing
the AP.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
The OSU Providers List includes two providers, so there should be two
OSU_METHOD values listed just like there was two OSU_SERVER_URI URLs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed to allow sigma_dut to enable ap_isolate=1. In addition,
verify that the two associated STAs with RSN(EAP) and OSEN cannot
exchange frames between them.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
P2P related configuration should be done on a global control interface.
This way this test can be reused also when a dedicated P2P device
interface is used.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
It looks like tshark parser was broken at some point for
wlan.mesh.config.cap which is now (tshark 2.6.3) pointing to incorrect
field (same as wlan.mesh.config.ps_protocol). This used to work with
tshark 2.2.6.
For now, assume the capability field ends up being the last octet of the
frame.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It looks like at least tshark 2.6.3 uses a different error message for
unknown display filter fields:
tshark: Neither "wlan_mgt.fixed.category_code" nor "4" are field or protocol names.
and a different status exit code (2 instead of 1).
Add a new handler for this combination to allow automatic wlan_mgt to
wlan conversion to happen.
Signed-off-by: Jouni Malinen <j@w1.fi>
This test starts two identical APs and assumes a connection to the first
one, though it is not necessary true. Fix that by starting the second AP
only after the connection is established.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This test case had an error that hit an unexpected disconnection. Add an
explicit check to verify that this does not happen anymore.
Signed-off-by: Jouni Malinen <j@w1.fi>
The channel configuration in CHAN_SWITCH command was incorrect. This
resulted in switching to HT40+ channel, while announcing HT40- in the
secondary channel IE. This caused a disconnection after the channel
switch. Fix that.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Verify that PMF does not end up reporting unexpected status code 30
(temporary rejection; SA Query).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This verifies that wpa_supplicant and hostapd behave consistently with
PMKSA caching when Suite B AKMs end up deriving a new PMKID from each
4-way handshake.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is a regression test case for a memory leak on DPP_CONFIGURATOR_ADD
error path in dpp_keygen_configurator() when an unsupported curve is
specified.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that the automatically generated network profile is able to
connect to a non-FT network automatically after having used FT for the
first connection.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that EAP-AKA' client rejects Challenge with an appended AT_KDF
and a modified AT_KDF value during KDF negotiation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Check that the @1@ macro gets replaced correctly both when in the middle
and when in the end of the URL template.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed with the modified hostapd implementation to fix the
ap_hs20_terms_and_conditions* test cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It is easier to understand the hostapd debug log here if each step is
noted there before starting the wpa_supplicant operation. In addition,
it looks safer to process all pending event messages between each step
to avoid running out of any buffer limits.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This test case verifies that wpa_supplicant is able to perform CSA to a
VHT80 channel when having to move the GO due to an avoid-frequencies
driver event.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The implementation changes in hostapd FT error path handling in the
follow commit would result in ap_ft_ap_oom7 test case failing. This is
triggered partially by PMF protections and SA Query attempts, so it
looks like it is easier to split each failure case into a separate test
case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Couple of "invalid value" tests started to fail now that mac80211_hwsim
actually accepts power save configuration. Fix these by running the same
command for more code coverage, but in a way that ignores the result of
the operation (succeeds with older kernel versions and fails with
newer).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
For testing purposes, enable TLS v1.3 in the authentication server so
that the protocol version can be controlled from wpa_supplicant side
more easily.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like OpenSSL 1.1.1 accepted the openssl_ciphers=FOO test
configuration or well, at least does not reject it like previous
versions did. For now, ignore this failure.
Signed-off-by: Jouni Malinen <j@w1.fi>
RC4-SHA cipher case ended up allowing the handshake to be started just
to fail with "no ciphers available" when trying to generate ClientHello.
Fix this by handling an EAP failure case for the RC4-SHA test step with
OpenSSL 1.1.*.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify that the AP initialization failure is reported back to
wpa_supplicant also when the initialization is complete in a callback.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
time.sleep() in run_roams() is required because the target AP sets the
key once the station was associated. There are races, when the station
processes the (Re)Association Response frame AND the test suite starts
FT_DS before the AP processes its local confirmation and thus
wpa_auth_sm_event(ASSOC_FT). Therefore, the ActionFrame will be lost, as
the AP driver is missing the key.
Since this is this speed is highly synthetic, wait a few milliseconds
before roaming back.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This is a regression test for a sequence where wpa_supplicant interface
MAC address is changed externally and the ifdown-ifup sequence is
processed only after the interface has already been set UP.
Signed-off-by: Jouni Malinen <j@w1.fi>
Test the hostapd venue_url configuration parameter. In addition, fix the
previous defined gas_anqp_venue_url test case to use correct encoding of
the Venue URL ANQP-element payload (URLs were missing and Venue Number
was off-by-one).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This test case uses EAP-MSCHAPv2 within the PEAP tunnel, so verify that
the build includes support for that before running the test.
Signed-off-by: Sean Parkinson <sean@wolfssl.com>
Enable appropriate Suite B test cases with BoringSSL. Currently, this
means enabling only the 192-bit level ECDSA and ECDHE-RSA since
BoringSSL has removed support for DHE and there is no need to support
128-bit level ECDSA anymore.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
On Fedora 26, start.sh fails with these error messages.
Failed to connect to wpa_supplicant global interface: /tmp/wpas-wlan0 error: Permission denied
Failed to connect to wpa_supplicant global interface: /tmp/wpas-wlan0 error: Permission denied
...
This is because Fedora 26 uses "wheel" group as administrative group.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This is used in the tests, too, and was already covered by the build.sh
script, but not this README file.
Signed-off-by: Vasyl Vavrychuk <vvavrychuk@gmail.com>
Clear the model_name parameter back to the default (empty string) at the
beginning and the end of dbus_set_global_properties to avoid failures if
the test case is run multiple times.
Signed-off-by: Jouni Malinen <j@w1.fi>
Ignore any unexpected deviceLost event before the peer devices has been
discovered. This works around issues where the previous test case
terminates before the D-Bus events have been fully delivered. This could
happen, e.g., when running dbus_p2p_discovery twice in a row.
Signed-off-by: Jouni Malinen <j@w1.fi>
Wait for the configuration exchange to complete before issuing the
DPP_STOP_LISTEN command to avoid confusing sequence of operation between
the ongoing and immediately following DPP exchanges.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Fix bssid2 value to make scanning more reliable for the second OWE BSS.
In addition, reorder the STA status checks to happen before the data
connectivity check to get more accurate failure reason into the log if
the test case fails.
Signed-off-by: Jouni Malinen <j@w1.fi>
Linux kernel commit c9491367b759 ("mac80211: always update the PM state
of a peer on MGMT / DATA frames") enforces the AP to check only
mgmt/data frames PM bit, and to update station's power save accordingly.
When sending only a PS-Poll (control frame) the AP will ignore the PM
bit. As the result, the partial virtual bitmap will not be updated, and
the test ap_open_disconnect_in_ps will fail on tshark check. Since the
test needs only the TIM to be updated, setting PS enabled will send NDP
that will signal that the station is sleeping. Sending PS-Poll to enable
power save is not correct, according to the following standard
statement: "A PS-Poll frame exchange does not necessarily result in an
Ack frame from the AP, so a non-AP STA cannot change power management
mode using a PS-Poll frame."
Signed-off-by: Adiel Aloni <adiel.aloni@intel.com>
This does not really work with mac80211_hwsim due to missing offload
support, but at least some minimal extra code coverage can be achieved.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This makes it a bit clearer to see which parameters need to be modified
if the test vector needs to be recreated based on new values.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that PMF can be marked required OWE networks and verify that a
station in transition mode can connect to an open network.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that unexpected 2048-bit RSA client certificate gets rejected by
the RADIUS server if the server is configured to use Suite B at 192-bit
level.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that unexpected p256 client certificate gets rejected if the
server is configured to use Suite B at 192-bit level.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
PMF is supposed to be enabled automatically in sigma_dut, so remove
the explicit argument to do so from the commands.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
All SAE and OWE associations are expected to require PMF to be
negotiated, so enable or require PMF in AP and STA configurations
accordingly to match the new sigma_dut behavior.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
GnuTLS seems to require the intermediate CA certificate to be included
both in the ca_cert and client_cert file for the cases of server and
client certificates using different intermediate CA certificates. Use
the user_and_ica.pem file with GnuTLS builds and reorder the
certificates in that file to make this work with GnuTLS.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check for unexpected connection to avoid timeout on TLS alert event if
the implementation does not check DH key size at all.
Signed-off-by: Jouni Malinen <j@w1.fi>
Need to ignore missing RX-ANQP event for the FILS Realm Info if
wpa_supplicant build does not include FILS support.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit b488a12948 ('Clear PMK length and
check for this when deriving PTK') started rejecting PTK derivation
based on PMK length. This reduced coverage from the eapol-fuzzer, so set
the default length when initializing the state machine in the fuzzer to
reach the previously used code paths.
Signed-off-by: Jouni Malinen <j@w1.fi>
Wait for test/allocation failure for longer than the wait_fail_trigger()
default two seconds to allow DPP (in particular, PKEX) retransmission to
occur. This removes some issues where the previous wait was more or less
exactly the same duration as the retransmission interval and the first
Listen operation not always starting quickly enough to receive the first
frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
When executing ./start.sh with OpenSSL 1.1.0f, an OCSP operation fails.
Put "-sha256" ahead of "-serial" to fix this.
~# openssl version
OpenSSL 1.1.0f 25 May 2017
~# openssl ocsp -reqout /lkp/benchmarks/hwsim/tests/hwsim/logs/current/ocsp-req.der -issuer /lkp/benchmarks/hwsim/tests/hwsim/auth_serv/ca.pem -serial 0xD8D3E3A6CBE3CD12 -no_nonce -sha256
ocsp: Digest must be before -cert or -serial
ocsp: Use -help for summary.
~# openssl ocsp -reqout /lkp/benchmarks/hwsim/tests/hwsim/logs/current/ocsp-req.der -issuer /lkp/benchmarks/hwsim/tests/hwsim/auth_serv/ca.pem -sha256 -serial 0xD8D3E3A6CBE3CD12 -no_nonce
Signed-off-by: leishaoting <leist.fnst@cn.fujitsu.com>
src/crypto/libcrypto.a and src/tls/libtls.a have circular references
and will need special handling with the linker at least for the time
being. This could be cleaned up eventually, but for now, provide a
mechanism to get the program linked.
This was already done in tests/Makefile, but tests/eapol-fuzzer/Makefile
needs the same.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not include this argument in normal case, but add a test case to
cover the special extra check case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This test case is not really realistic and the second connection attempt
would fail if additional AES-based ciphers get provisioned. Work this
around by dropping to CCMP only if other ciphers are present.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to avoid false errors with GCMP-256 and CCMP-256 to be
added in the implementation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The kernel started enforcing attribute lengths, and nl80211.py had been
doing it all wrong - the padding must be present, but not part of the
length.
Fix it to do it the right way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These test cases were failing when run immediately after
dpp_pkex_test_fail. It looks like timing of the TX status and the short
eloop wait were getting reordered in this cases. This ended up with some
of the DPP-TX-STATUS event messages missing. Instead of explicitly
checking for those message, simply count the number of DPP-TX messages
to verify that the correct number of retries are being sent.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Fix problem when running ap_ft test cases with real HW using remote
tests and hwsim wrapper by using the newer hostapd.app_ap() API.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
These VHT160 with DFS cases were in a single test case to optimize test
execution time with parallel wait for the 60 second CAC. However, this
design has become difficult to support with the kernel changes that
allow radar events to be shared between interfaces. To avoid need for
more workarounds here just for testing purposes, split this into two
test cases so that conflicting events from another interface do not
cause the test case to fail.
Signed-off-by: Jouni Malinen <j@w1.fi>
These DFS radar detection cases were in a single test case to optimize
test execution time with parallel wait for the 60 second CAC. However,
this design has become difficult to support with the kernel changes that
allow radar events to be shared between interfaces. To avoid need for
more workarounds here just for testing purposes, split this into two
test cases so that conflicting events from another interface do not
cause the test case to fail.
Signed-off-by: Jouni Malinen <j@w1.fi>
mac80211_hwsim module typically dumps a lot of details into the kernel
message buffer. While it's probably okay in a dedicated VM, it's way too
chatty in other setups.
The kernel allows fine-tuning logging via the dynamic debugging
facility. Let's enable all logging locations in the mac80211_hwsim
module so that we don't loose debugging output when the kernel adopts
the dynamic debug mechanism for the driver.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
