If the OWE network profile matches an open network which does not
advertise OWE BSS, allow open connection. The new owe_only=1 network
profile parameter can be used to disable this transition mode and
enforce connection only with OWE networks.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This was originally added to allow the IEEE 802.11 protocol to be
tested, but there are no known fully functional implementations based on
this nor any known deployments of PeerKey functionality. Furthermore,
PeerKey design in the IEEE Std 802.11-2016 standard has already been
marked as obsolete for DLS and it is being considered for complete
removal in REVmd.
This implementation did not really work, so it could not have been used
in practice. For example, key configuration was using incorrect
algorithm values (WPA_CIPHER_* instead of WPA_ALG_*) which resulted in
mapping to an invalid WPA_ALG_* value for the actual driver operation.
As such, the derived key could not have been successfully set for the
link.
Since there are bugs in this implementation and there does not seem to
be any future for the PeerKey design with DLS (TDLS being the future for
DLS), the best approach is to simply delete all this code to simplify
the EAPOL-Key handling design and to get rid of any potential issues if
these code paths were accidentially reachable.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new sae_password network profile parameter can now be used to set
the SAE password instead of the previously used psk parameter. This
allows shorter than 8 characters and longer than 63 characters long
passwords to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends OWE support in wpa_supplicant to allow DH groups 20 and 21
to be used in addition to the mandatory group 19 (NIST P-256). The group
is configured using the new network profile parameter owe_group.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds new wpa_supplicant configuration parameters (go_interworking,
go_access_network_type, go_internet, go_venue_group, go_venue_type) to
add a possibility of configuring the P2P GO to advertise Interworking
element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant network parameter group_mgmt can be used to
specify which group management ciphers (AES-128-CMAC, BIP-GMAC-128,
BIP-GMAC-256, BIP-CMAC-256) are allowed for the network. If not
specified, the current behavior is maintained (i.e., follow what the AP
advertises). The parameter can list multiple space separate ciphers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the code that writes mesh_rssi_threshold to a network block
always executes, but the code that reads it from network block and the
code that initializes it to a default value in a new network block are
inside #ifdef CONFIG_MESH. As a result when writing a config file it
will write mesh_rssi_threshold (since it has a non-default value) and
later fail to read the network block.
Fix this by moving the write code under #ifdef CONFIG_MESH as well.
Note, network blocks which already have mesh_rssi_threshold because of
the bug will still fail to read after the fix.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
wpa_supplicant can now be configured to generate a network profile
automatically based on DPP configuration. The following
dpp_config_processing values can be used to specify the behavior:
0 = report received configuration to an external program for
processing; do not generate any network profile internally (default)
1 = report received configuration to an external program and generate
a network profile internally, but do not automatically connect
to the created (disabled) profile; the network profile id is
reported to external programs
2 = report received configuration to an external program, generate
a network profile internally, try to connect to the created
profile automatically
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While encoded == NULL could happen in the case of an empty blob, that
will result in encoded_len == 0 and base64_decode() not derefencing the
src argument. That seems to be too difficult for some static analyzers,
so to avoid false warnings, explicitly reject the encoded == NULL case
without even trying to base64 decode it. (CID 164709)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This exposes user configurable option to set bssid_hint for a network.
bssid_hint indicates which BSS has been found a suitable candidate for
initial association for drivers that use driver/firmware-based BSS
selection. Unlike the bssid parameter, bssid_hint does not limit the
driver from selecting other BSSs in the ESS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In some practical cases, it is useful to suppress joining to node in the
distance. The new field mesh_rssi_threshold could be used as RSSI
threshold for joining.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
If the uuid configuration parameter is not set, wpa_supplicant generates
an UUID automatically to allow WPS operations to proceed. This was
previously always using an UUID generated from the MAC address. This
commit adds an option to use a random UUID instead. The type of the
automatically generated UUID is set with the auto_uuid parameter: 0 =
based on MAC address (default; old behavior), 1 = random UUID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds an option to configure wpa_supplicant to use the perfect
forward secrecy option in FILS shared key authentication. A new build
option CONFIG_FILS_SK_PFS=y can be used to include this functionality. A
new runtime network profile parameter fils_dh_group is used to enable
this by specifying which DH group to use. For example, fils_dh_group=19
would use FILS SK PFS with a 256-bit random ECP group.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since VHT can be toggled explicitly, also expose being able to disable
HT explicitly, without requiring HT overrides. Continue making it
default to enabled though.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of deducing the wide (HT, VHT) channel configuration only
automatically in P2P mode, allow it to be configured in the network
in non-P2P mode.
Also allow all of these parameters to be configured through the control
interface or the configuration file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The userspace may want to delay the the first scheduled scan.
This enhances sched_scan to add initial delay (in seconds) before
starting first scan cycle. The driver may optionally choose to
ignore this parameter and start immediately (or at any other time).
This uses NL80211_ATTR_SCHED_SCAN_DELAY to add this via user
global configurable option: sched_scan_start_delay.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support for rejecting a BSS transition request using MBO reject
reason codes. A candidate is selected or rejected based on whether it is
found acceptable by both wpa_supplicant and the driver. Also accept any
candidate meeting a certain threshold if disassoc imminent is set in BTM
Request frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support to send GAS requests with a randomized transmitter address
if supported by the driver. The following control interface commands
(and matching configuration file parameters) can be used to configure
different types of randomization:
"SET gas_rand_mac_addr 0" to disable randomizing TX MAC address,
"SET gas_rand_mac_addr 1" to randomize the complete TX MAC address,
"SET gas_rand_mac_addr 2" to randomize the TX MAC address except for OUI.
A new random MAC address will be generated for every
gas_rand_addr_lifetime seconds and this can be configured with
"SET gas_rand_addr_lifetime <timeout>".
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a new wpa_supplicant network profile parameter
mka_priority=0..255 to set the priority of the MKA Actor.
Signed-off-by: Badrish Adiga H R <badrish.adigahr@gmail.com>
Configuration file network block with disabled=2 is used for storing
information about a persistent group, so p2p_persitent_group should be
updated according to this when creating a struct wpa_ssid instance. This
will end up using D-Bus persistent network object path for the network.
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Kyeong-Chae Lim <kcya.lim@samsung.com>
Previously, wpa_supplicant only supported hardcoded port == 1 in the
SCI, but users may want to choose a different port.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
So that the user can turn encryption on (MACsec provides
confidentiality+integrity) or off (MACsec provides integrity only). This
commit adds the configuration parameter while the actual behavior change
to disable encryption in the driver is handled in the following commit.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This enables configuring key_mgmt=NONE + mka_ckn + mka_cak.
This allows wpa_supplicant to work in a peer-to-peer mode, where peers
are authenticated by the pre-shared (CAK,CKN) pair. In this mode, peers
can act as key server to distribute keys for the MACsec instances.
This is what some MACsec switches support, and even without HW
support, it's a convenient way to setup a network.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Add configuration options that control publishing of fine timing
measurement (FTM) responder and initiator functionality via bits 70, 71
of Extended Capabilities element. Typically, FTM functionality is
controlled by a location framework outside wpa_supplicant. When
framework is activated, it will use wpa_supplicant to configure the
STA/AP to publish the FTM functionality. See IEEE P802.11-REVmc/D7.0,
9.4.2.27.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
The new network profile parameter group_rekey can now be used to specify
the group rekeying internal in seconds for IBSS.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE Std 802.11-2012, 10.19 (Public Action frame addressing) specifies
that the wildcard BSSID value is used in Public Action frames that are
transmitted to a STA that is not a member of the same BSS.
wpa_supplicant used to use the actual BSSID value for all such frames
regardless of whether the destination STA is a member of the BSS.
P2P does not follow this rule, so P2P Public Action frame construction
must not be changed. However, the cases using GAS/ANQP for non-P2P
purposes should follow the standard requirements.
Unfortunately, there are deployed AP implementations that do not reply
to a GAS request sent using the wildcard BSSID value. The previously
used behavior (Address3 = AP BSSID even when not associated) continues
to be the default, but the IEEE 802.11 standard compliant addressing
behavior can now be configured with gas_address3=1.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new parameter wps_disabled to network block (wpa_ssid). This
parameter allows WPS functionality to be disabled in AP mode.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Add cellular capability attribute to MBO IE and add MBO IE with cellular
capabilities to Probe Request frames. By default, cellular capability
value is set to Not Cellular capable (3).
Signed-off-by: David Spinadel <david.spinadel@intel.com>
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for IEEE 802.11ad devices.
Add a new "pbss" argument to network block. The argument is used
in the following scenarios:
1. When network has mode=2 (AP), when pbss flag is set will start
as a PCP instead of an AP.
2. When network has mode=0 (station), when pbss flag is set will
connect to PCP instead of AP.
The function wpa_scan_res_match() was modified to match BSS according to
the pbss flag in the network block (wpa_ssid structure). When pbss flag
is set it will match only PCPs, and when it is clear it will match only
APs.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
This patch keeps ip_addr* configuration in conf file while
updating supplicant conf file either internally by supplicant or
due to save_config command.
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Since hostapd supports ACS now, let's enable its support in
wpa_supplicant as well when starting AP mode.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
[u.oelmann@pengutronix.de: rebased series from hostap_2_1~944 to master]
[u.oelmann@pengutronix.de: adjusted added text in defconfig]
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Add the option to configure scheduled scan plans in the config file.
Each scan plan specifies the interval between scans and the number
of scan iterations. The last plan will run infinitely and thus
specifies only the interval between scan iterations.
usage:
sched_scan_plans=<interval:iterations> <interval2:iterations2> ... <interval>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
A new network profile configuration parameter max_oper_chwidth=3 can be
used to specify preference to enable 80+80 MHz VHT channel for IBSS. If
that is set, the first 80 MHz segment is specified based on the
frequency parameter in the network profile and the second segment is
selected automatically (which will practically be limited to a single
possibility due to DFS requirements in most countries).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Some APs may send RSC octets in EAPOL-Key message 3 of 4-Way Handshake
or in EAPOL-Key message 1 of Group Key Handshake in the opposite byte
order (or by some other corrupted way). Thus, after a successful
EAPOL-Key exchange the TSC values of received multicast packets, such as
DHCP, don't match the RSC one and as a result these packets are dropped
on replay attack TSC verification. An example of such AP is Sapido
RB-1732.
Work around this by setting RSC octets to 0 on GTK installation if the
AP RSC value is identified as a potentially having the byte order issue.
This may open a short window during which older (but valid)
group-addressed frames could be replayed. However, the local receive
counter will be updated on the first received group-addressed frame and
the workaround is enabled only if the common invalid cases are detected,
so this workaround is acceptable as not decreasing security
significantly. The wpa_rsc_relaxation global configuration property
allows the GTK RSC workaround to be disabled if it's not needed.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Config file is written to a temp file and then it is renamed to the
original config file. However, it is possible that the rename operation
will be commited to storage while file data will be still in cache
causing original config file to be empty or partially written in case of
a system reboot without a clean shutdown. Make this less likely to occur
by forcing the data to be written to the storage device before renaming
the file.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Upon any change in the currently used channels evaluate if a GO should
move to a different operating frequency, where the possible scenarios:
1. The frequency that the GO is currently using is no longer valid,
due to regulatory reasons, and thus the GO must be moved to some
other frequency.
2. Due to Multi Concurrent Channel (MCC) policy considerations, it would
be preferable, based on configuration settings, to prefer Same
Channel Mode (SCM) over concurrent operation in multiple channels.
The supported policies:
- prefer SCM: prefer moving the GO to a frequency used by some other
interface.
- prefer SCM if Peer supports: prefer moving the GO to a frequency
used by some other station interface iff the other station
interface is using a frequency that is common between the local and
the peer device (based on the GO Negotiation/Invitation signaling).
- Stay on the current frequency.
Currently, the GO transition to another frequency is handled by a
complete tear down and re-setup of the GO. Still need to add CSA flow to
the considerations.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The mesh SAE auth often fails with master branch. By bisect I found
commit eb5fee0bf5 ('SAE: Add side-channel
protection to PWE derivation with ECC') causes this issue. This does not
mean the commit has a bug. This is just a CPU resource issue.
After the commit, sae_derive_pwe_ecc() spends 101(msec) on my PC (Intel
Atom N270 1.6GHz). But dot11RSNASAERetransPeriod is 40(msec). So
auth_sae_retransmit_timer() is always called and it can causes
continuous frame exchanges. Before the commit, it was 23(msec).
On the IEEE 802.11 spec, the default value of dot11RSNASAERetransPeriod
is defined as 40(msec). But it looks short because generally mesh
functionality will be used on low spec devices. Indeed Raspberry Pi B+
(ARM ARM1176JZF-S 700MHz) requires 287(msec) for new
sae_derive_pwe_ecc().
So this patch makes the default to 1000(msec) and makes it configurable.
This issue does not occur on infrastructure SAE because the
dot11RSNASAERetransPeriod is not used on it.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
These configuration parameters did not use matching printf format string
parameters (signed vs. unsigned). While these configuratin values are,
in practice, small unsigned integers, the implementation should use
matching types to write these.
Signed-off-by: Jouni Malinen <j@w1.fi>
1. Add global p2p_cli_probe property to enable/disable Probe Request
frame RX reporting for connected P2P Clients. The property can be set to
0 - disable or 1 - enable. The default value is 0.
2. Enable Probe Request frame RX reporting for P2P Client on
WPA_COMPLETED state if p2p_cli_probe property is set to 1. Disable it
when an interface state is changing to any other state.
3. Don't cancel Probe Request frame RX reporting on wpa_stop_listen for
a connected P2P Client handling Probe Request frames.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
