This adds survey dump support for all frequencies
and for specific desired frequencies. This will later
be used by ACS code for spectrum heuristics.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
This splits up the channel checking upon initialization into a few
helpers. This should make this a bit easier to follow. This also paves
the way for some initial ACS entry code.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Interfaces that take one or two seconds to reconfigure the link after we
set IFF_ALLMULTI or after we bring the interface up were dropping the
initial TX EAPOL packet which caused excessive delays in authentication.
This change applies to FreeBSD/DragonFly only.
Signed-hostap: Rui Paulo <rpaulo@FreeBSD.org>
Add additional input verification for the frequency parameter in
p2p_group_add (and other P2P operations for that matter). Without this
verification invalid freq could be set and not handled properly.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
In AP mode the frequency was initialized only after trying to set up the
AP which caused failure. Move AP frequency initialization to the right
place. This allows an AP mode network block without the frequency
parameter to be used with the default channel 11 being selected in that
case.
Signed-hostap: Avraham Stern <avraham.stern@intel.com>
When 'p2p_group_remove *' is called while the station interface
is connected, the flow also disconnects the station interface.
Fix this by skipping non-P2P interfaces in the iteration.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
According to WSC specification (Ver 2.0.2, section 8.3), RF Bands
attribute should be set to the specific RF band used for the current
message. Add an option to set wanted band in wps_build_rf_bands() and
add a callback to get the current band from wpa_supplicant and hostapd.
Signed-hostap: David Spinadel <david.spinadel@intel.com>
It is possible that when trying to remove a dynamically added interface,
changing its type to station mode is not possible (since the kernel does
not support so in its interface combinations).
Since P2P interfaces are always dynamically added, avoid changing their
type to station in the deinit_ap() and deinit_p2p_client() nl80211
callbacks, assuming that the interface is about to be removed.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Reduce the wait time for the monitor control interfaces to get
messages on wpa_supplicant de-init etc., as this significantly delays
the shutdown of the wpa_supplicant.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
The pad field in the RRB messages is unused, but it should be
initialized to avoid sending out arbitrary data from stack. This was
also generating number of valgrind complaints about uninitialized memory
accesses in local FT tests.
Signed-hostap: Jouni Malinen <j@w1.fi>
It looks like some virtual host setups are too slow to get
wpa_supplicant initialized under valgrind and this was triggering test
failures. Work around this by using even a longer wait before test case
execution.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 8e12685c43 replaced call to
nl80211_mgmt_unsubscribe() on the deinit path with a
wpa_driver_nl80211_set_mode() call. This is not enough to unregister the
bss->nl_mgmt read socket in all cases. Fix this by unconditionally
unsubscribing from the nl80211 events after having change mode to
station.
Signed-hostap: Jouni Malinen <j@w1.fi>
In case a control interface socket is detached because of sendmsg()
failing for the socket, function call to detach the socket uses a
pointer to the socket information in the structure to be freed. Reorder
code to print socket info before freeing the data to avoid use of freed
memory in case debug prints are enabled.
Signed-hostap: Jouni Malinen <j@w1.fi>
It looks like valgrind could not under buildbot with the default file
mode. Fix this by making wpa_supplicant and hostapd binaries readable
and executable by everyone.
Signed-hostap: Jouni Malinen <j@w1.fi>
./run-all.sh can now take an optional argument to select whether to run
all test cases as before (default), to run these under valgrind
("valgrind"), to run P2P test cases with concurrent station interface
("concurrent"), or the concurrent P2P test cases under valgrind
("concurrent-valgrind").
valgrind cases report errors if a test case fails or valgrind reports an
error.
Signed-hostap: Jouni Malinen <j@w1.fi>
This keeps wpa_supplicant from hanging forever if the other end of the
socket dies. This is similar to the earlier commit
4fdc8def88 to make the global control
interface befave in the same way.
Signed-hostap: Jouni Malinen <j@w1.fi>
print and logger.info() were directing output to different locations
(stdout and stderr, respectively) which resulted in buildbot showing
reordered entries. Use logger consistently to avoid that.
Signed-hostap: Jouni Malinen <j@w1.fi>
It looks like the NOTE commands can time out in some cases. Avoid
stopping the test run in such a case to get more coverage if this is a
temporary issue.
Signed-hostap: Jouni Malinen <j@w1.fi>
The design for launching AP mode interfaces was changed, but
start-p2p-concurrent.sh was not updated with matching changes.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, wpa_supplicant behavior in WEP configuration was to try to
mimic a device that is not aware of WPA/WPA2 and as such, it tried to
connect to a WPA/WPA2 AP with the assumption that the AP could be
providing support for both WEP and WPA/WPA2 stations in the same BSS.
Such APs could have been used during transition from WEP to more secure
options, but that type of deployment have not been used in large number
and are not really of much use anymore taken into account that more or
less all new devices support WPA/WPA2. That combined with the preference
to deprecate WEP justifies removing this use case and making WEP
networking matching more strict by using the knowledge of AP advertising
WPA/WPA2 as an indication of WEP not being supported.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit c7a67a7719 forced disconnection
when wpas_clear_wps() is called. Call this function from a registered
timeout when processing a failure event in order to allow the WPS
handshake to be completed with WSC_NACK and EAP-Failure.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new wps_get_status command can be used to fetch the result of the
latest WPS operation and the current PBC state from hostapd.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
drv->assoc_freq was not updated during the connect command (neither
during the command's invocation nor after getting the event) unlike with
auth/assoc case where assoc_freq is updated. This resulted in
nl80211_get_link_noise() (and any other function for that matter) using
the improper drv->assoc_freq value with drivers that use the connect
API. Fix this by updating drv->assoc_freq on connect command and when
fetching the frequency from the driver.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Stop AP command can be used by the driver as an event to indicate that
AP mode has stopped operation. WLAN driver may have encountered errors
that has forced the driver to report this event or concurrent operations
on virtual interfaces may have forced AP operation to be stopped. When
in P2P GO mode, wpa_supplicant uses this event to remove P2P group to
keep in sync with the driver state.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This reverts commit ce970851af.
It turned out that this breaks lots of use cases where p2p_find is
issued while already in p2p_listen state. As such, we cannot reject
p2p_find this easily without checking for more specific cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
Though p2p_find is not expected during ongoing P2P connection, it is
possible that any third party application issues a p2p_find resulting in
connection failure. Address this by rejecting any p2p_find command while
connection is in progress.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A transmission failure of the TDLS Setup Request frame (TPK Handshake
M1) results in no further retries and the peer entry being left in state
where all TDLS Setup Request frames from the peer with higher address
would be rejected, thus always resulting in a failure to establish a
TDLS link. Handle the failures in transmission by disabling the link
immediately to ensure the traffic to the peer goes through the AP. This
commit also handles similar transmision failures for TPK Handshake M2
and M3 frames (TDLS Setup Response and Confirm).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
cfg80211 does not allow the zero duration of remain-on-channel. Instead,
use 20 ms as default waiting time when remain-on-channel is used to
schedule offchannel transmission that does not expect a response.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
4-way handshake may fail under extremely noisy environment and if this
happens during P2P group formation, the 10 second extra delay added in
wpas_auth_failed() can result in running over the 15 second timeout.
Avoid this by skipping the delay mechanism in wpas_auth_failed() for the
P2P group formation case. The P2P formation timeout will take care of
stopping the attempts if the failure condition does not get resolved.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The nl80211 command for setting the TX index does not distinguish TDLS
vs. AP key and as such, the driver would not know what this set TX key
index operation is doing in the TDLS case. This could result in the TX
key index for AP being changed instead if static WEP is used in the AP
connection. Fix the issue by not setting TX key index when configuring a
TDLS key.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Make sure the connection between each STA and the AP is in working state
between each TDLS setup/teardown operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
