It looked like cfg80211 BSS entry for the zero-length SSID could remain
after this test case. Stop the AP and scan twice with flush-cache option
to make this less likely to occur and cause issues to following test
cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
ML80211_ATTR_TDLS_OPERATION can now set to NL80211_TDLS_DISCOVERY_REQ to
allow the driver to request wpa_supplicant to initiate TDLS Discovery
Request.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the TDLS operation request mechanism to allow TDLS
Discovery Request to be initiated by the driver similarly to the
existing Setup and Teardown requests.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible to leave the driver in mesh point state if upper layer
mesh initialization failed in wpa_supplicant_mesh_init(). With nl80211,
this results in the vif being left in mesh point mode instead of
restoring it to station mode. That seems to break normal functionality,
e.g., for Public Action frame TX/RX. Fix this by restoring station mode
on mesh failure path.
This error could be triggered, e.g., with the following hwsim test case
sequence: wpas_mesh_secure_sae_missing_password
nfc_p2p_static_handover_tagdev_go_forced_freq
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, it was possible for the wpa_sm_start_preauth() and
wpa_sm_rekey_ptk() eloop callbacks to remain active after disconnection
and potentially continue to be used for the next association. This is
not correct behavior, so explicitly cancel these timeouts to avoid
unexpected attempts to complete RSN preauthentication or to request PTK
to be rekeyed.
It was possible to trigger this issue, e.g., by running the following
hwsim test case sequence: ap_wpa2_ptk_rekey ap_ft_sae_over_ds
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for this test case to fail if cfg80211 BSS cache
included an entry for the same BSSID on another channel from an earlier
test case. Fix this by epxlicitly flushing the cache. In addition, use
scan_for_bss() to make the test less likely to fail in case of heavy CPU
load.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The initial IEEE 802.11 ProxyARP functionality in the kernel needed
changes in behavior and that ended up requiring an independent
configuration parameter to be used. Update hostapd to use that new
proxyarp_wifi parameter instead of the earlier proxyarp.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This converts the QCA vendor event to EVENT_DFS_* events for the case
of DFS offloaded to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add radar event processing logic for AP/P2P GO. The DFS processing
functions from hostapd are now used for these wpa_supplicant cases as
well for both offloaded and non-offloaded DFS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add P2P changes to allow bringing up P2P autonomous GO on a DFS channel
if DFS functionality is offloaded to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Modify the string for AP-CSA-FINISHED event indication to include a flag
which tells the framework whether the new channel is a DFS channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add handling logic for DFS offloaded case, and add a helper function
that takes the frequency (MHz) as a param and returns 1 if given channel
requires DFS, or 0 otherwise.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If DFS is offloaded to the driver, hostapd should not be performing
these operations. Send the relevant control interface events to provide
information to upper layer software that may use such events to track
DFS/CAC state. This makes the offloaded DFS implementation more
consistent with the DFS-in-hostapd behavior.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, it was possible for wpa_state to be left at SCANNING if
INTERWORKING_SELECT command failed to find any match. Now the state is
set to DISCONNECTED if the operation terminates because of no matching
networks.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The way the current channel survey is implemented in mac80211_hwsim
requires for the ACS test cases to be run immediately after the same
radio has been on the expected operating band. This was worked around in
one of the test cases and errors ignored in couple. Extend this
workaround to cover all the test cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When there is no channel preference mentioned by user, auto GO
can be started on any of the 5 GHz channels supported for P2P.
Consider operating classes 115 and 124 which do not require DFS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 3f9ebc439c ('P2P: Allow AP/GO
interface to be started while P2P-in-progress') moved the
wpa_s->connect_without_scan and wpa_s->last_scan_req checks to an
earlier place within the wpa_supplicant_scan() function without
adjusting wpa_s->last_scan_req. This variable was set between the old
and new location, so the new location needs to use wpa_s->scan_req.
This fixes an issue where AP/GO operations were not properly started in
some operation sequence. Instead, a station mode scan was executed. This
issue could be triggered, e.g., by running the no_go_freq test case
followed by autogo_random_channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like the IP routing table changes used here to trigger
unreachability and following reachability of the server do not work very
well with full IP routing configuration, so run this test case only when
executed under vm-run.sh.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces a callback to notify any configuration updates
from the eap_proxy layer. This is used to trigger re-reading of IMSI and
MNC length.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Static analyzers may warn about dereference before NULL check in
wpas_network_disabled() due to the new code added to check
wpa_s->p2p_mgmt. wpa_s cannot be NULL here, so remove the unneeded check
for it later in the function. (CID 106124)
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_supplicant_deinit_iface() ends up removing all P2P groups if the
removed interface is the parent interface. This is correct behavior in
general, but this resulted in issues in the new group interface
initialization error path since wpa_s->parent was not assigned before
hitting this check. Fix this by assigning wpa_s->parent as part of
wpa_supplicant_add_iface().
Signed-off-by: Jouni Malinen <j@w1.fi>
If a connection with the primary server cannot be established, restore
connection to the previously used server.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd.conf parameter radius_client_addr can now be used to
select a specific local IP address to be used as the RADIUS client
address.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 347c55e216 ('RADIUS client: Re-try
connection if socket is closed on retransmit') added a new option for
initialing RADIUS server failover from radius_client_retransmit(), but
ended up trying to change authentication servers when accounting server
was supposed to be changed due to a copy-paste issue.
Signed-off-by: Jouni Malinen <j@w1.fi>
These test cases verify that P2P_FIND and P2P_LISTEN operation continues
after having replied to GO Negotiation Request frame for which we are
not yet ready (i.e., GO Negotiation Response with status=1).
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the GO Negotiation Response (failure) TX status to
be processed at a point where there is no P2P timeout to continue
search. Avoid stopping the ongoing search operation by explicitly
restarting it from this callback.
Signed-off-by: Jouni Malinen <j@w1.fi>
There are number of cases where wpa_supplicant requests the current
connection to be disconnected before starting a new operation. Such
cases do not really indicate that there was an error in connecting or a
disconnection initiated by the AP, so do not add a temporary blacklist
entry in such sequences.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for the P2P_CONNECT control interface command to be
issued on an incorrect interface. While the upper layer component should
really use global control interface for this, make this work by
redirecting the command to the correct context if needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
The dedicated P2P management instance (wpas->p2p_mgmt == 1) using
cfg80211 P2P Device cannot be used for non-P2P uses or connection (there
is no netdev). Reject or ignore such operations to avoid unexpected
operations if enabled network blocks are configured in the
wpa_supplicant instance used to control this interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
