SM Power Save was described in somewhat unclear manner in IEEE Std
802.11n-2009 as far the use of it locally in an AP to save power. That
was clarified in IEEE Std 802.11-2016 to allow only a non-AP STA to use
SMPS while the AP is required to support an associated STA doing so. The
AP itself cannot use SMPS locally and the HT Capability advertisement
for this is not appropriate.
Remove the parts of SMPS support that involve the AP using it locally.
In practice, this reverts the following commits:
04ee647d58 ("HT: Let the driver advertise its supported SMPS modes for AP mode")
8f461b50cf ("HT: Pass the smps_mode in AP parameters")
da1080d721 ("nl80211: Advertise and configure SMPS modes")
Signed-off-by: Jouni Malinen <j@w1.fi>
The HE Operation field for BSS color consists of a disabled, a partial,
and 6 color bits. The original commit adding support for BSS color
considered this to be a u8. This commit changes this to the actual
bits/values.
This adds an explicit config parameter for the partial bit. The disabled
is set to 0 implicitly if a bss_color is defined.
Interoperability testing showed that stations will require a BSS color
to be set even if the feature is disabled. Hence the default color is 1
when none is defined inside the config file.
Signed-off-by: John Crispin <john@phrozen.org>
Initial OWE implementation used SHA256 when deriving the PTK for all OWE
groups. This was supposed to change to SHA384 for group 20 and SHA512
for group 21. The new owe_ptk_workaround parameter can be used to enable
workaround for interoperability with stations that use SHA256 with
groups 20 and 21. By default, only the appropriate hash function is
accepted. When workaround is enabled (owe_ptk_workaround=1), the
appropriate hash function is tried first and if that fails, SHA256-based
PTK derivation is attempted. This workaround can result in reduced
security for groups 20 and 21, but is required for interoperability with
older implementations. There is no impact to group 19 behavior.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This has nothing to do with OWE and parsing of this value was not
supposed to be within an ifdef CONFIG_OWE block.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Application Extension attribute is defined in WSC tech spec v2.07 page
104. Allow hostapd to be configured to add this extension into WPS IE in
Beacon and Probe Response frames. The implementation is very similar to
vendor extension.
A new optional entry called "wps_application_ext" is added to hostapd
config file to configure this. It enodes the payload of the Application
Extension attribute in hexdump format.
Signed-off-by: Veli Demirel <veli.demirel@airties.com>
Signed-off-by: Bilal Hatipoglu <bilal.hatipoglu@airties.com>
The new hostapd gtk_rsc_override and igtk_rsc_override configuration
parameters can be used to set an override value for the RSC that the AP
advertises for STAs for GTK/IGTK. The contents of those parameters is a
hexdump of the RSC in little endian byte order.
This functionality is available only in CONFIG_TESTING_OPTIONS=y builds.
This can be used to verify that stations implement initial RSC
configuration correctly for GTK/ and IGTK.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add support to exclude non-PSC 6 GHz channels from the input frequency
list to ACS. The new acs_exclude_6ghz_non_psc=1 parameter can be used by
6 GHz only APs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The channel numbers are duplicated between 2.4 GHz / 5 GHz bands and 6
GHz band. Hence, add support to configure a list of frequencies to ACS
(freqlist) instead of a list of channel numbers (chanlist). Also, both 5
GHz and 6 GHz channels are referred by HOSTAPD_MODE_IEEE80211A. The 6
GHz channels alone can be configured by using both mode and frequency
list.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This new hostapd configuration parameter rsnxe_override_eapol=<hexdump>
can be used to override RSNXE value in EAPOL-Key msg 3/4 for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This parameter can be used to specify which PWE derivation mechanism(s)
is enabled. This commit is only introducing the new parameter; actual
use of it will be address in separate commits.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
hostapd is by default waiting STA to send SAE Confirm before sending the
SAE Confirm. This can now be configured with sae_confirm_immediate=1
resulting in hostapd sending out SAE Confirm immediately after sending
SAE Commit.
These are the two different message sequences:
sae_confirm_immediate=0
STA->AP: SAE Commit
AP->STA: SAE Commit
STA->AP: SAE Confirm
AP->STA: SAE Confirm
STA->AP: Association Request
AP->STA: Association Response
sae_confirm_immediate=1
STA->AP: SAE Commit
AP->STA: SAE Commit
AP->STA: SAE Confirm
STA->AP: SAE Confirm
STA->AP: Association Request
AP->STA: Association Response
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add two new configuration parameters for hostapd:
enable_edmg: Enable EDMG capability for AP mode in the 60 GHz band
edmg_channel: Configure channel bonding for AP mode in the 60 GHz band
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
The new hostapd and wpa_supplicant configuration parameters dpp_name and
dpp_mud_url can now be used to set a specific name and MUD URL for the
Enrollee to use in the Configuration Request. dpp_name replaces the
previously hardcoded "Test" string (which is still the default if an
explicit configuration entry is not included). dpp_mud_url can
optionally be used to add a MUD URL to describe the Enrollee device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
IEEE Std 802.11F-2003 was withdrawn in 2006 and as such it has not been
maintained nor is there any expectation of the withdrawn trial-use
recommended practice to be maintained in the future. Furthermore,
implementation of IAPP in hostapd was not complete, i.e., only parts of
the recommended practice were included. The main item of some real use
long time ago was the Layer 2 Update frame to update bridges when a STA
roams within an ESS, but that functionality has, in practice, been moved
to kernel drivers to provide better integration with the networking
stack.
Signed-off-by: Jouni Malinen <j@w1.fi>
Hardcode this to be defined and remove the separate build options for
PMF since this functionality is needed with large number of newer
protocol extensions and is also something that should be enabled in all
WPA2/WPA3 networks.
Signed-off-by: Jouni Malinen <j@w1.fi>
Allow the previously hardcoded maximum numbers of EAP message rounds to
be configured in hostapd EAP server. This can be used, e.g., to increase
the default limits if very large X.509 certificates are used for EAP
authentication.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter eap_teap_id can be used to
configure the expected behavior for used identity type.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new eap_teap_separate_result=1 hostapd configuration parameter can
be used to test TEAP exchange where the Intermediate-Result TLV and
Crypto-Binding TLV are send in one message exchange while the Result TLV
exchange in done after that in a separate message exchange.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration option eap_sim_id can now be used to
disable use of pseudonym and/or fast reauthentication with EAP-SIM,
EAP-AKA, and EAP-AKA'.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an SQLite table for defining per station MAC address version of
radius_auth_req_attr/radius_acct_req_attr information. Create the
necessary table and index where this doesn't exist. Select attributes
from the table keyed by station MAC address and request type (auth or
acct), parse and apply to a RADIUS message.
Add radius_req_attr_sqlite hostapd config option for SQLite database
file. Open/close RADIUS attribute database for a lifetime of a BSS and
invoke functions to add extra attributes during RADIUS auth and
accounting request generation.
Signed-off-by: Terry Burton <tez@terryburton.co.uk>
We will want to parse RADIUS attributes in config file format when
retrieving them from an SQLite database.
Signed-off-by: Terry Burton <tez@terryburton.co.uk>
hostapd EAP server can now be configured with two separate server
certificates/keys to enable parallel operations using both RSA and ECC
public keys. The server will pick which one to use based on the client
preferences for the cipher suite (in the TLS ClientHello message). It
should be noted that number of deployed EAP peer implementations do not
filter out the cipher suite list based on their local configuration and
as such, configuration of alternative types of certificates on the
server may result in interoperability issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds support for a new EAP method: EAP-TEAP (Tunnel Extensible
Authentication Protocol). This should be considered experimental since
RFC 7170 has number of conflicting statements and missing details to
allow unambiguous interpretation. As such, there may be interoperability
issues with other implementations and this version should not be
deployed for production purposes until those unclear areas are resolved.
This does not yet support use of NewSessionTicket message to deliver a
new PAC (either in the server or peer implementation). In other words,
only the in-tunnel distribution of PAC-Opaque is supported for now. Use
of the NewSessionTicket mechanism would require TLS library support to
allow arbitrary data to be specified as the contents of the message.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a config option to allow setting a custom Basic NSS/MCS set. As a
default we use single stream HE-MCS 0-7.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
The initial commit used srp instead of spr for the spatial reuse
configuration prefix.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
This adds support to hostapd for configuring airtime policy settings for
stations as they connect to the access point. This is the userspace
component of the airtime policy enforcement system PoliFi described in
this paper: https://arxiv.org/abs/1902.03439
The Linux kernel part has been merged into mac80211 for the 5.1 dev
cycle.
The configuration mechanism has three modes: Static, dynamic and limit.
In static mode, weights can be set in the configuration file for
individual MAC addresses, which will be applied when the configured
stations connect.
In dynamic mode, weights are instead set per BSS, which will be scaled
by the number of active stations on that BSS, achieving the desired
aggregate weighing between the configured BSSes. Limit mode works like
dynamic mode, except that any BSS *not* marked as 'limited' is allowed
to exceed its configured share if a per-station fairness share would
assign more airtime to that BSS. See the paper for details on these
modes.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
SPR allows us to detect OBSS overlaps and allows us to do adaptive CCA
thresholds. For this to work the AP needs to broadcast the element
first.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
The new hostapd configuration parameter dpp_controller can now be used
with the following subparameter values: ipaddr=<IP address>
pkhash=<hexdump>. This adds a new Controller into the configuration
(i.e., more than one can be configured) and all incoming DPP exchanges
that match the specified Controller public key hash are relayed to the
particular Controller.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Very short beacon intervals can be useful for certain scenarios such
as minimising association time on PBSSs. Linux supports a minimum of
10[1] so let's reduce the minimum to match that.
[1] https://elixir.bootlin.com/linux/latest/ident/cfg80211_validate_beacon_int
Signed-off-by: Brendan Jackman <brendan.jackman@bluwireless.co.uk>
This patch added 'check_cert_subject' support to match the value of
every field against the DN of the subject in the client certificate. If
the values do not match, the certificate verification will fail and will
reject the user.
This option allows hostapd to match every individual field in the right
order, also allow '*' character as a wildcard (e.g OU=Development*).
Note: hostapd will match string up to 'wildcard' against the DN of the
subject in the client certificate for every individual field.
Signed-off-by: Paresh Chaudhary <paresh.chaudhary@rockwellcollins.com>
Signed-off-by: Jared Bents <jared.bents@rockwellcollins.com>
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter wps_cred_add_sae=1 can be used
to request hostapd to add SAE configuration whenever WPS is used to
configure the AP to use WPA2-PSK and the credential includes a
passphrase (instead of PSK). This can be used to enable WPA3-Personal
transition mode with both SAE and PSK enabled and PMF enabled for PSK
and required for SAE associations.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The Wi-Fi Alliance Multi-AP Specification v1.0 allows onboarding of a
backhaul STA through WPS. To enable this, the WPS Registrar offers a
different set of credentials (backhaul credentials instead of fronthaul
credentials) when the Multi-AP subelement is present in the WFA vendor
extension element of the WSC M1 message.
Add new configuration options to specify the backhaul credentials for
the hostapd internal registrar: multi_ap_backhaul_ssid,
multi_ap_backhaul_wpa_psk, multi_ap_backhaul_wpa_passphrase. These are
only relevant for a fronthaul SSID, i.e., where multi_ap is set to 2 or
3. When these options are set, pass the backhaul credentials instead of
the normal credentials when the Multi-AP subelement is present.
Ignore the Multi-AP subelement if the backhaul config options are not
set. Note that for an SSID which is fronthaul and backhaul at the same
time (i.e., multi_ap == 3), this results in the correct credentials
being sent anyway.
The security to be used for the backaul BSS is fixed to WPA2PSK. The
Multi-AP Specification only allows Open and WPA2PSK networks to be
configured. Although not stated explicitly, the backhaul link is
intended to be always encrypted, hence WPA2PSK.
To build the credentials, the credential-building code is essentially
copied and simplified. Indeed, the backhaul credentials are always
WPA2PSK and never use per-device PSK. All the options set for the
fronthaul BSS WPS are simply ignored.
Signed-off-by: Davina Lu <ylu@quantenna.com>
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Cc: Marianna Carrera <marianna.carrera.so@quantenna.com>
The new sae_password parameter [|vlanid=<VLAN ID>] can now be used to
assign stations to a specific VLAN based on which SAE Password
Identifier they use. This is similar to the WPA2-Enterprise case where
the RADIUS server can assign stations to different VLANs and the
WPA2-Personal case where vlanid parameter in wpa_psk_file is used.
Signed-off-by: Jouni Malinen <j@w1.fi>
When I replaced the POS() function with ffs() when applying relevant
parts from the original patch, this ended up breaking the frame
construction since the POS() function was supposed to count the bit
offset for the mask with 0 being the LSB instead of 1 returned by ffs().
Furthermore, ffs() is not available in all C libraries (e.g., not
directly exposed by strings.h on Android), so better not depend on that
or compiler builtins for this since there is no need for this to be as
fast as possible in configuration parsing.
Fix this with a simple function to determine the number of bits the
value needs to be shifted left to align with the mask.
Fixes: 11ce7a1bc3 ("HE: Add MU EDCA Parameter Set element (AP)")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This patch adds a new flag 'crl_reload_interval' to reload CRL
periodically. This can be used to reload ca_cert file and the included
CRL information on every new TLS session if difference between the last
reload and the current time in seconds is greater than
crl_reload_interval.
This reloading is used for cases where check_crl is 1 or 2 and the CRL
is included in the ca_file.
Signed-off-by: Paresh Chaudhary <paresh.chaudhary@rockwellcollins.com>
Signed-off-by: Jared Bents <jared.bents@rockwellcollins.com>
There is currently no support for setting hostapd_bss_config.pbss from a
config file, i.e., it was used only based on automatic logic in
wpa_supplicant. This patch adds a key naturally called "pbss" which can
be used to set it.
Cc: Antony King <antony.king@bluwirelesstechnology.com>
Signed-off-by: Brendan Jackman <brendan.jackman@bluwirelesstechnology.com>
Add support for configuring parameters for the MU EDCA Parameter Set
element per IEEE P802.11ax/D3.0.
Signed-off-by: Siva Mullati <siva.mullati@intel.com>
Some distributions (e.g., Debian) have started introducting systemwide
OpenSSL policies to disable older protocol versions and ciphers
throughout all programs using OpenSSL. This can result in significant
number of interoperability issues with deployed EAP implementations.
Allow explicit wpa_supplicant (EAP peer) and hostapd (EAP server)
parameters to be used to request systemwide policies to be overridden if
older versions are needed to be able to interoperate with devices that
cannot be updated to support the newer protocol versions or keys. The
default behavior is not changed here, i.e., the systemwide policies will
be followed if no explicit override configuration is used. The overrides
should be used only if really needed since they can result in reduced
security.
In wpa_supplicant, tls_disable_tlsv1_?=0 value in the phase1 network
profile parameter can be used to explicitly enable TLS versions that are
disabled in the systemwide configuration. For example,
phase1="tls_disable_tlsv1_0=0 tls_disable_tlsv1_1=0" would request TLS
v1.0 and TLS v1.1 to be enabled even if the systemwide policy enforces
TLS v1.2 as the minimum version. Similarly, openssl_ciphers parameter
can be used to override systemwide policy, e.g., with
openssl_ciphers="DEFAULT@SECLEVEL=1" to drop from security level 2 to 1
in Debian to allow shorter keys to be used.
In hostapd, tls_flags parameter can be used to configure similar
options. E.g., tls_flags=[ENABLE-TLSv1.0][ENABLE-TLSv1.1]
Signed-off-by: Jouni Malinen <j@w1.fi>
An AP might reject a STA association request due to low RSSI. In such
case, the AP informs the STA the desired RSSI improvement and a retry
timeout. The STA might retry to associate even if the RSSI hasn't
improved if the retry timeout expired.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Add the ability to ignore time-based CRL errors from OpenSSL by
specifying a new configuration parameter, check_crl_strict=0.
This causes the following:
- This setting does nothing when CRL checking is not enabled.
- When CRL is enabled, "strict mode" will cause CRL time errors to not
be ignored and will continue behaving as it currently does.
- When CRL is enabled, disabling strict mode will cause CRL time
errors to be ignored and will allow connections.
By default, check_crl_strict is set to 1, or strict mode, to keep
current functionality.
Signed-off-by: Sam Voss <sam.voss@rockwellcollins.com>
This makes it possible to use ECDSA certificates with EAP-TLS/TTLS/etc.
It should be noted that when using Suite B, different mechanism is used
to specify the allowed ECDH curves and this new parameter must not be
used in such cases.
Signed-off-by: Hristo Venev <hristo@venev.name>
This makes it easier to integrate dynamic VLANs in custom network
configurations. The bridge name is added after the interface name in the
vlan_file line, also separated by whitespace.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The purpose of Multi-AP specification is to enable inter-operability
across Wi-Fi access points (APs) from different vendors.
This patch introduces one new configuration parameter 'multi_ap' to
enable Multi-AP functionality and to configure the BSS as a backhaul
and/or fronthaul BSS.
Advertise vendor specific Multi-AP capabilities in (Re)Association
Response frame, if Multi-AP functionality is enabled through the
configuration parameter.
A backhaul AP must support receiving both 3addr and 4addr frames from a
backhaul STA, so create a VLAN for it just like is done for WDS, i.e.,
by calling hostapd_set_wds_sta(). Since Multi-AP requires WPA2 (never
WEP), we can safely call hostapd_set_wds_encryption() as well and we can
reuse the entire WDS condition.
To parse the Multi-AP Extension subelement, we use get_ie(): even though
that function is meant for parsing IEs, it works for subelements.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This adds support for hostapd-as-RADIUS-authentication-server to request
subscription remediation for SIM-based credentials. The new hostapd.conf
parameter hs20_sim_provisioning_url is used to set the URL prefix for
the remediation server for SIM provisioning. The random
hotspot2dot0-mobile-identifier-hash value will be added to the end of
this URL prefix and the same value is stored in a new SQLite database
table sim_provisioning for the subscription server implementation to
use.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new hostapd configuration parameter hs20_release can be used to
configure the AP to advertise a specific Hotspot 2.0 release number
instead of the latest supported release. This is mainly for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
