This patch adds support for wired IEEE 802.1X client on the Solaris.
I have tested with these:
OS : OpenSolaris 2009.06
EAP : EAP-MD5
Switch : Cisco Catalyst 2950
The driver is likely to indicate an immediate signal event when the
threshold value is configured. Since we do this immediately after
association, there is not much point in requesting a new scan to be
started based on this event.
The driver is likely to indicate an immediate signal event when the
threshold value is configured. Since we do this immediately after
association, there is not much point in requesting a new scan to be
started based on this event.
This removes quite a bit of duplicated code and allows network block
priority configuration to be used to prefer unprotected networks and
also allows use on open network with good signal strength even if
scan results show a protected network with marginal signal strength
that does not allow it to be used.
The wpa_supplicant compilation without CONFIG_WPS option results in
messages below.
scan.c: In function 'wpa_supplicant_scan':
scan.c:246: warning: unused variable 'wps'
This trivial patch erases this warning.
This clears up authentication state in the driver and in case of
cfg80211, unlocks the BSS entry for the previously used AP. The
previous commit cf4783e35f changed
only the ctrl_iface DISCONNECT command behavior; this new commit
does the same for D-Bus commands.
wpa_s->bssid is already cleared by mark_disassoc() when we're getting the
disassociation event for the case where wpa_supplicant requested
disassociation. wpa_s->sme.prev_bssid holds the BSSID we need to check
for, so use that instead.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When passing several authentication algorithms through auth_alg, we
should try all of them when the first one fails. The wext driver goes
through the connect nl80211 command and the retries are then handled by
the kernel. The nl80211 doesn't and we have to handle that from
userspace.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is needed to avoid trying to reassociate based on new scan
results when using wpa_supplicant to control AP mode. This could
happen if something external triggered the driver to run a scan.
When SME is in wpa_supplicant (mac80211), we need to make sure that
the kernel code has valid BSS entry for the AP. In some cases it
seemed to be possible to end up not having current information in
cfg80211 or mac80211 which can result to association failures. Avoid
this by always running through the scan request before initial
connection attempt.
It is possible that l2_packet is not used with wpa_supplicant
in some cases, so better make sure we do not end up notifying
l2_packet code about authentications unless it was actually
initialized in the first place.
Store list of all discovered BSSes in the ESS and on which frequencies
they have been seen. Use this information to dynamically generated the
list of channels for background scans.
The AP configuration may change after provisioning, so it is better
not to use the current security policy to prioritize results. Instead,
use WPS Selected Registrar attribute as the main sorting key and use
signal strength next without considering security policy or rate sets.
The non-WPS provisioning case remains as-is, i.e., this change applies
only when trying to find an AP for WPS provisioning.
Addition of the background scanning mechanism in commit
60b94c9819 moved the scan trigger
into a new function that was also incrementing the scan_runs
counter, but the removal of the previous scan_runs incrementation
was forgotten from that patch. This counter should only be updated
into a single location, so remove the old one. This improves AP
selection for WPS provisioning by not skipping some of the initial
scans.
wps_er_config can now be used to configure an AP. It is similar to
wps_er_learn, but instead of only learning the current AP settings,
it continues to send M8 with the new settings for the AP.
wps_er_start command now takes an optional parameter that can be used
to configure a filter to only allow UPnP SSDP messages from the
specified IP address. In practice, this limits the WPS ER operations
to a single AP and filters out all other devices in the network.
This avoids an invalid D-Bus call during interface initialization.
The wpa_state change can happen before the D-Bus interface is set up,
so we must be preparted to handle this early event signal. In theory,
it should be possible to reorder initialization code to make sure
D-Bus signals are ready, but that would likely require quite a bit of
code restructuring, so it looks like a safer option for now is to just
skip the early event.
The wpa_supplicant compilation with CONFIG_AP option and without
CONFIG_IEEE80211R, CONFIG_WPS, NEED_SME, CONFIG_CLIENT_MLME options
results in following messages.
../src/ap/drv_callbacks.o: In function `hostapd_notif_assoc':
../src/ap/drv_callbacks.c:59: undefined reference to
`ieee802_11_parse_elems'
gmake: *** [wpa_supplicant] Error 1
Add a new wpa_supplicant state: interface disabled. This can be used
to allow wpa_supplicant to be running with the network interface even
when the driver does not actually allow any radio operations (e.g.,
due to rfkill).
Allow driver_nl80211.c and driver_wext.c to start while rfkill is in
blocked state (i.e., when ifconfig up fails) and process rfkill
events to block/unblock WLAN.
Use regular expression matches to see if input is not the (now translated?)
string "Select any network" and is a "<network id>: <ssid>" string or the
"all" keyword where that is applicable.
Signed-off-by: Kel Modderman <kel@otaku42.de>
This allows wpa_supplicant to be started quickly with an empty
configuration. If an external program wants to fetch scan results
from wpa_supplicant, it will need to request a scan explicitly
in this type of case.
