Set device_name in the test cases instead of relying on the
wpa_supplicant configuration file. This fixes problems when we run WPS
test cases in remote test environment.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Add a new command line option -f (--modules) that will run all test
cases from the specified module(s).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Leaving out the special sae_pwe value was causing failures for following
test cases, e.g., in the following sequence:
sigma_dut_sae_pw_id_pwe_loop sae_password_id_only
Signed-off-by: Jouni Malinen <j@w1.fi>
Some test case sequences seemed to prevent the station from completing
the first OBSS scan (that scan was aborted) and that resulted in failing
the test case because the AP had not received any report in time. Wait
for scan completion and allow additional scans before timing out to
avoid indicating incorrect AP behavior in cases where the report was not
even received.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
WEP should not be used for anything anymore. As a step towards removing
it completely, move all WEP related functionality to be within
CONFIG_WEP blocks. This will be included in builds only if CONFIG_WEP=y
is explicitly set in build configuration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Update the fizzing test tools to use the new set_key() prototype, i.e.,
add the new key_flag argument, to get rid of compiler warnings.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit f3bcd69603 ("Remove CONFIG_IEEE80211N build option") broke
couple of fuzzing test tools due to missing wpa_scan_results_free(). Fix
that by pulling in driver_common.o.
Signed-off-by: Jouni Malinen <j@w1.fi>
Update grpform_pbc_overlap not to require PBC session overlap to be
detected since in this sequence a single BSSID is specified and other
APs can be ignored while checking for session overlap. Add other test
cases to explicitly check for the PBC session overlap detection in
non-P2P and P2P cases when the BSSID is specified.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Replace the hardcoded /tmp filenames for generated ACL and BSS
configuration files with proper temporary files from tempfile.mkstemp()
to avoid conflicts with existing files or with parallel uses. Remove ACL
files from the local directory at the end of each test case. BSS files
are currently left behind, but can be cleaned up separately if needed
for non-VM testing (VM testing has those on ramdrive so they get dropped
automatically at the end) and for remote devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
When this test case is ran in remote test environment, there could be
additional APs in scan results after bssid_filter has been disabled.
That breaks the check on SCAN_RESULTS output. Extend this to cover the
remote testing case by using bssid_filter with both known APs listed
instead of full wildcard.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Instead of hardcoded bss-[1-6]*.conf files, generate them using the
correct BSSID for each AP device and send/install them on the remote
client as well if needed.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Generate ACL files instead of using files with hardcoded values for the
STA MAC addresses. Send the generated files also to the remote client if
required.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Some hostapd test cases use configuration files, e.g., ACLs in BSS
configuration. When executing remote tests (udp), we have to first send
these configuration files to the appropriate remote device. The new
send_file() helper can be used for that.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
We could have different ifconfig output formats on the remote devices,
so make the parser more flexible to handle such cases.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
This allows more test cases to be run in remote setup. Previously, we
used to block all test cases that required more than two arguments
(i.e., that needed the params argument).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
In case the hwsim wrapper is used in remote tests, show also which
device will be used as
apdev - hostapd
dev - wpa_supplicant
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Kill hostapd and wpa_supplicant based on the configuration parameters.
Previously, we could have killed wrong processes.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Hardcoded CONFIG_IEEE80211N to be included to clean up implementation.
More or less all new devices support IEEE 802.11n (HT) and there is not
much need for being able to remove that functionality from the build.
Included this unconditionally to get rid of one more build options and
to keep things simpler.
Signed-off-by: Jouni Malinen <j@w1.fi>
