No need to run a full scan as the first step since it only needs to find
the AP from a known channel for the GAS operation.
Signed-hostap: Jouni Malinen <j@w1.fi>
Now that wpa_supplicant requests the driver (cfg80211) to clear its scan
cache automatically after each BSS_FLUSH/FLUSH command, the previously
used ignore_old_scan_res workaround should not be needed for the hwsim
test cases anymore.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add test cases to use connect command instead of auth+assoc commands and
AP mode operations using the old monitor interface design.
Signed-hostap: Jouni Malinen <j@w1.fi>
NOTE: Actual use of the direct link (DLS) is not supported in
mac80211_hwsim, so this operation fails at setting the keys after
successfully completed 4-way handshake. This test case does allow the
key negotiation part to be tested for coverage, though.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds number of test cases to go through various possible EAP
configurations for Interworking network selection.
Signed-hostap: Jouni Malinen <j@w1.fi>
This extends P2P test coverage to include the case of separate group
interface use with autonomous GO and group formation through GO
negotiation.
Signed-hostap: Jouni Malinen <j@w1.fi>
This fixes the user.key file (incorrect key was copied previously) and
adds a test case for EAP-TLS with WPA2-Enterprise.
Signed-hostap: Jouni Malinen <j@w1.fi>
This increases EAP method coverage for WPA2-Enterprise to include
EAP-pwd, EAP-GPSK, EAP-SAKE, EAP-EKE, EAP-IKEv2, EAP-PAX, and EAP-PSK.
Signed-hostap: Jouni Malinen <j@w1.fi>
The run-tests.py -l argument does not take an argument value anymore.
Instead, debug output is directed to a separate file <test>.log for each
test case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
test_ap_change_ssid verifies that the SET and RELOAD control interface
commands can be used to change the SSID of a hostapd-controlled WPA2-PSK
AP, i.e., for a case where the PSK needs to be derived again after the
SSID change.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies network selection using 3GPP Network Information and
connection using EAP-SIM with GSM authentication handled by an external
program.
Signed-hostap: Jouni Malinen <j@w1.fi>
cfg80211/mac80211 seems to getting stuck with scans every now and then.
Check for this special state and delay return from reset() until the
driver has stopped the scan operation. This reduces likelihood of
failing multiple test cases in a row because of a single error.
Signed-hostap: Jouni Malinen <j@w1.fi>
test_p2p_go_invite verifies that GO can invite a peer in a case where
the operating channel and peer's listen channel are different.
Signed-hostap: Jouni Malinen <j@w1.fi>
This avoids some issues with the global control interface socket
getting stuck with send buffer limit reached if test cases did not
use wait_global_event().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Some test runs have resulted in wpa_supplicant being unresponsive or
very slow on the control interface. Check for that type of issues as
part of the reset sequence that is done between each test case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows more consistent interface to be used regardless of which
P2P driver design is used (especially for P2P management operations
over netdev vs. dedicated P2P_DEVICE).
Signed-hostap: Jouni Malinen <j@w1.fi>
The WPS tests are more prone to fail if scan results from the previous
test cases are allowed to remain in the wpa_supplicant BSS table during
the consecutive test since the test setup uses the same BSSID for the
test APs that change their configuration. Avoid these mostly bogus
issues by enforcing wpa_supplicant to drop and ignore old scan results
during the WPS test cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
