This makes the initial OBSS scans in AP mode before starting 40 MHz BSS
more robust. In addition, HT20 can be used as a backup option if none of
the scans succeed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the minimal HT 20/40 co-ex support to include dynamic changes
during the lifetime of the BSS. If any STA connects to a 2.4 GHz AP with
40 MHz intolerant bit set then the AP will switch to 20 MHz operating
mode.
If for a period of time specified by OBSS delay factor and OBSS scan
interval AP does not have any information about 40 MHz intolerant STAs,
the BSS is switched from HT20 to HT40 mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When primary and secondary channel were switched and config was
reloaded, secondary channel was incorrectly overwritten.
Proceed as for other settings that should not be changed and don't
allow to overwrite.
Signed-off-by: Pawel Kulakowski <pawel.kulakowski@tieto.com>
Especially when multiple BSSes are used with ACS, number of the error
paths were not cleaning up driver initialization properly. This could
result in using freed memory and crashing the process if ACS failed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There was possibility that the current channel in Beacon information
element was incorrectly set. This problem was easily observed when
primary and secondary channel were switched and then some of hostapd
settings (for example password) were changed using WPS External
Registrar. This caused hostapd_reload_config() function overwrite the
current channel information from config file.
This patch prevents this situation and does not allow to overwrite
channel and some other settings when config is reloaded.
Signed-off-by: Pawel Kulakowski <pawel.kulakowski@tieto.com>
It was possible for the control interface and some of the BSS setup to
be left partially initialized in failure cases while the BSS structures
were still freed. Fix this by properly cleaning up anything that may
have passed initialization successfully before freeing memory.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, some of the last initialization steps could fail without
clearly marking the interface disabled. For example, configuring the
channel to the driver could fail, but hostapd would not clearly identify
as the interface not being in functional state apart from not moving it
to the ENABLED state. Send an AP-DISABLED event and mark interface state
DISABLED if such a setup operation fails.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, this was enabled only at msgdump verbosity level, but any
level that is more verbose than it should also be included.
Signed-off-by: Jouni Malinen <j@w1.fi>
handle_assoc_cb() got this addition, but the check in
hostapd_new_assoc_sta() was not modified to be aware of the OSEN special
case for EAPOL state machines to be used for marking a STA authorized.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This was done in handle_assoc_cb() in ieee802_11.c for drivers that use
hostapd SME/MLME. However, drivers that include SME/MLME implementation
do not use that function and the STA flag needs to be set when
processing the association notification. This is needed to get the STA
entry into showing the proper authorized state and to get the
AP-STA-CONNECTED/DISCONNECTED events on the control interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds an option to optimize AP teardown by leaving the
deletion of keys (including group keys) and stations to the driver.
This optimization option should be used if the driver supports stations
and keys removal when stopping an AP.
For example, the optimization option will always be used for cfg80211
drivers since cfg80211 shall always remove stations and keys when
stopping an AP (in order to support cases where the AP is disabled
without the knowledge of wpa_supplicant/hostapd).
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
If hapd_iface->bss[i] == NULL, this could have resulted in NULL pointer
dereference in the debug print. Avoid this by skipping the message in
case of NULL pointer. In addition, clear iface->bss[i] to NULL for
additional robustness even though this array gets freed immediately.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like leaving behind the freed pointed at the end of the array
could end up in a crash triggered by double free in some cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows NAS-IP-Address, NAS-Identifier, and NAS-IPv6-Address to be
included in the Disconnect-Request packets.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When a station is disconnected based on Disconnect-Request, it is better
to force the station to go through full EAP authentication if it tries
to reconnect.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Before this patch, 1 second timeout was used for regulatory updates. In
some cases, specially when we reload driver modules on some slower
platforms this could take more than 1 second (about 2 seconds). This is
important specially for DFS case, where we have to have correct DFS
region before we will start CAC. In other case (unknown DFS region), CAC
will fail. 5 seconds should be enough for all cases.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
It is possible for the configuration to be temporarily invalid when
adding a new AP through SET commands followed by ENABLE. Avoid this
issue by using less strict validation on SET commands and perform full
configuration validation only on ENABLE. Use cases with configuration
file maintain their previous behavior, i.e., full validation after the
file has been read.
Signed-hostap: Jouni Malinen <j@w1.fi>
These were somewhat more hidden to avoid direct use, but there are now
numerous places where these are needed and more justification to make
the extern int declarations available from wpa_debug.h. In addition,
this avoids some warnings from sparse.
Signed-hostap: Jouni Malinen <j@w1.fi>
When CSA flow starts, store the entire struct hostapd_freq_params and
not only CS frequency as it was before. The additional freq_params are
required to advertise CS supplementary IEs such as secondary channel,
wide bandwidth CS, etc.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This allows use of structs (and not only pointers) defined in drivers.h.
Remove also some not needed forward declarations and redundant includes.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
If more BSSes are added in config file than are supported by the driver,
segmentation fault can appear. For this case, the interface_added flag
needs to be cleared if adding a new BSS fails.
Signed-hostap: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Some non-mac80211 drivers, such as ath6kl, support STA inactivity timer
in firmware and may not provide connected stations' idle time to the
userspace. If the driver indicates support for offloaded operation, do
not start the inactivity timer in the hostapd.
Signed-hostap: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
struct beacon_data contains a lot of pointers. Make sure it gets cleared
to zero if hostapd_build_beacon_data() gets called from a path that does
not clear the structure first.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
The 'started' state was tracked incorrectly. It also broke DFS
as it was using hostapd_enable/disable_iface() functions.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Build CSA settings and call the driver to perform the switch. Construct
Beacon, Probe Response, and (Re)Association Response frames both for CSA
period and for the new channel. These frames are built based on the
current configuration. Add CSA IE in Beacon and Probe Response frames.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
We were not filtering the EVENT_CHANNEL_LIST_CHANGED events based on the
regulatory hint initiator. So wait for EVENT_CHANNEL_LIST_CHANGED event
after our own change was triggered even when regulatory hint initiator
was the driver. This could result in the wait for the channel list to be
updated to be terminated before the real change has occurred and as
such, old channel list remaining in use when configuring
hostapd/wpa_supplicant country parameter. Fix this by filtering the
hints according to the initiator and only regulatory hints initiated by
user will be used to stop the wait.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for additional BSSs to be added while the primary
interface is still in the process of determining channel parameters (HT
co-ex scan, ACS, DFS). Do not enable secondary interfaces in such state
immediately, but instead, wait for the pending operation on the primary
interface to complete. Once that's done, the added extra BSSs will also
be enabled in hostapd_setup_interface_complete().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Reject multiple calls to hostapd_setup_bss() for any specific interface.
hostapd_cleanup() must have been called first before trying to restart a
BSS.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd_bss_deinit() takes care of freeing the associated stations and
calling hostapd_cleanup() to deinit per-BSS services.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This reverts parts of commit 390e489c0d
that tried to enable removal of the first BSS. Since that operation is
now forced to remove all BSSs, these changes are not needed. The
hostapd_if_remove() operation in hostapd_free_hapd_data() is problematic
for the first BSS since it ends up freeing driver wrapper information
that is needed later when deinitializing the driver wrapper.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since the control interface is now initialized as part of
hostapd_setup_interface(), it needs to be deinitialized on the error
path.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If a secondary BSS is removed while it is waiting for the primary BSS to
complete channel setup (e.g., due to HT co-ex scan, ACS, or DFS), the
hostapd_data instance has not yet been initialized. Fix the BSS removal
code to take this special case into account and not try to deinitialize
the hostapd_data instance that has not yet been started.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The changes in commit 5592065850 to allow
any BSS to be removed were a bit too early since there are still number
of areas that use the first BSS as a special case. Especially the
driver_ops API is going to require quite a bit of cleanup before removal
of the first BSS without the other BSSes of the same radio can be done
safely.
For now, force all BSSs to be removed in case the first one is removed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Limit the calls to eloop_terminate() to happen only for the
initialization failure from the interfaces that we specified on the
command line. This allows hostapd process to continue operating even if
a dynamically added interface fails to start up. This allows the upper
layer software to fix a configuration error and retry.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Better share the same function for initializing control interface from
the two possible paths that can add a new interface to hostapd.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is a per-BSS configuration parameter and as such, needs to be
configured to the driver from hostapd_setup_bss() instead of
hostapd_driver_init().
Signed-hostap: Jouni Malinen <j@w1.fi>
DFS operations are specific to the interface (radio/wiphy), not BSS
(netdev/vif), so hostapd_iface is the appropriate element to use in
them.
Signed-hostap: Jouni Malinen <j@w1.fi>
If per-BSS configuration enabling did not provide a phy name, iface->phy
was left empty. It can be helpful to set this up automatically, so fill
that when initializing the interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
If hostapd is requested to set the country code and the previous country
code differs from the new one, the channel list information from the
driver may change. This change may not be instant, so wait for an
EVENT_CHANNEL_LIST_CHANGED event before continuing interface setup with
fetching of the channel list information. This fixes issues where the
selected channel is not available based on the previous regulatory data
and update through CRDA takes some time.
Signed-hostap: Jouni Malinen <j@w1.fi>
