Commit graph

1130 commits

Author SHA1 Message Date
Jouni Malinen
b658547dd5 nl80211: Add build option for QCA vendor extensions
This allows the binary sizes to be reduced if no support for nl80211
vendor extensions are needed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-10-01 12:45:27 +03:00
Jouni Malinen
49c36b708e Add ChangeLog entries for v2.5
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-09-27 22:02:05 +03:00
Jouni Malinen
0e2412d086 Add option to reject authentication on 2.4 GHz from dualband STA
The new no_auth_if_seen_on=<ifname> parameter can now be used to
configure hostapd to reject authentication from a station that was seen
on another radio.

This can be used with enabled track_sta_max_num configuration on another
interface controlled by the same hostapd process to reject
authentication attempts from a station that has been detected to be
capable of operating on another band, e.g., to try to reduce likelihood
of the station selecting a 2.4 GHz BSS when the AP operates both a 2.4
GHz and 5 GHz BSS concurrently.

Note: Enabling this can cause connectivity issues and increase latency for
connecting with the AP.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-09-05 19:11:02 +03:00
Jouni Malinen
964f64e2ee Add option to ignore Probe Request frames on 2.4 GHz from dualband STA
The new no_probe_resp_if_seen_on=<ifname> parameter can now be used to
configure hostapd to not reply to group-addressed Probe Request from a
station that was seen on another radio.

This can be used with enabled track_sta_max_num configuration on another
interface controlled by the same hostapd process to restrict Probe
Request frame handling from replying to group-addressed Probe Request
frames from a station that has been detected to be capable of operating
on another band, e.g., to try to reduce likelihood of the station
selecting a 2.4 GHz BSS when the AP operates both a 2.4 GHz and 5 GHz
BSS concurrently.

Note: Enabling this can cause connectivity issues and increase latency
for discovering the AP.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-09-05 17:53:15 +03:00
Jouni Malinen
a65a9b8d67 hostapd: Add mechanism to track unconnected stations
hostapd can now be configured to track unconnected stations based on
Probe Request frames seen from them. This can be used, e.g., to detect
dualband capable station before they have associated. Such information
could then be used to provide guidance on which colocated BSS to use in
case of a dualband AP that operates concurrently on multiple bands under
the control of a single hostapd process.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-09-05 17:11:11 +03:00
Manikandan Mohan
4ae7120919 Allow wpa_cli/hostapd_cli client socket directory to be specified
This adds a new helper function wpa_ctrl_open2() that can be used
instead of wpa_ctrl_open() to override the default client socket
directory. Add optional -s<directory path> argument to hostapd_cli and
wpa_cli to allow the client socket directory to be specified.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-09-01 11:17:43 +03:00
Jouni Malinen
d9c807cab1 Fix key derivation for Suite B 192-bit AKM to use SHA384
While the EAPOL-Key MIC derivation was already changed from SHA256 to
SHA384 for the Suite B 192-bit AKM, KDF had not been updated similarly.
Fix this by using HMAC-SHA384 instead of HMAC-SHA256 when deriving PTK
from PMK when using the Suite B 192-bit AKM.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-08-27 20:42:14 +03:00
Jouni Malinen
681e199dfb EAP server: Add tls_session_lifetime configuration
This new hostapd configuration parameter can be used to enable TLS
session resumption. This commit adds the configuration parameter through
the configuration system and RADIUS/EAPOL/EAP server components. The
actual changes to enable session caching will be addressed in followup
commits.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-08-24 02:29:30 +03:00
Jouni Malinen
137b293963 Remove unnecessary NULL check from LOG_LEVEL handler
cmd cannot be NULL here, so there is no need to check it before calling
os_strlen().

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-08-22 00:22:12 +03:00
Jouni Malinen
bc02843e75 hostapd: Add testing option to override own WPA/RSN IE(s)
This allows the new own_ie_override=<hexdump> configuration parameter to
be used to replace the normally generated WPA/RSN IE(s) for testing
purposes in CONFIG_TESTING_OPTIONS=y builds.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-08-08 18:18:03 +03:00
Srinivas Dasari
5c4f0511a2 hostapd: Add support to configure debug log level at runtime
Add support to read/configure log_level using hostapd control interface
LOG_LEVEL command similarly to what was already supported in
wpa_supplicant.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-08-03 17:50:09 +03:00
Jouni Malinen
7cb53ded11 Add build option to remove all internal RC4 uses
The new CONFIG_NO_RC4=y build option can be used to remove all internal
hostapd and wpa_supplicant uses of RC4. It should be noted that external
uses (e.g., within a TLS library) do not get disabled when doing this.

This removes capability of supporting WPA/TKIP, dynamic WEP keys with
IEEE 802.1X, WEP shared key authentication, and MSCHAPv2 password
changes.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-08-02 16:52:56 +03:00
Jouni Malinen
6ee66b4251 OpenSSL: Add CONFIG_TLS_ADD_DL=y build option for hostapd
This behaves similarly to the same option in wpa_supplicant, i.e., adds
-ldl when linking in libcrypto from OpenSSL.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-07-28 21:00:18 +03:00
Jouni Malinen
16bc3b8935 OpenSSL: Add SHA256 support in openssl_tls_prf() for TLSv1.2
This is needed when enabling TLSv1.2 support for EAP-FAST since the
SSL_export_keying_material() call does not support the needed parameters
for TLS PRF and the external-to-OpenSSL PRF needs to be used instead.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-07-28 21:00:17 +03:00
Jouni Malinen
ff7a4bd13f FST: Do not replace previous attachment
hapd->iface->fst must not be overridden if it is already pointing to FST
instance. Without this, duplicated FST-ATTACH could result in memory
leak and process termination.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-07-25 19:52:27 +03:00
Jouni Malinen
ceb8a79c33 FST: Use -EINVAL instead of EINVAL as return value
This is more consistent with other error cases.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-07-25 19:50:43 +03:00
Jouni Malinen
de01710b08 hostapd: Add build options for selecting eloop type
This adds CONFIG_ELOOP_POLL=y and CONFIG_ELOOP_EPOLL=y options to
hostapd build options similarly to how these were implemented for
wpa_supplicant.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-23 18:48:41 +03:00
Jouni Malinen
63e169e149 hostapd: Mark config parameter name const
The functions parsing configuration parameters do not modify the name of
the parameter, so mark that function argument constant. In theory, the
value should also be const, but at least for now, number of the parser
functions end up modifying this to simplify parsing.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-21 13:56:19 +03:00
Anton Nayshtut
748febf344 hostapd: Add DUP_NETWORK global control interface command
This adds a new global control interface command DUP_NETWORK with the
following syntax:

DUP_NETWORK src_ifname dst_ifname param

The currently supported parameters:
  wpa
  wpa_key_mgmt
  wpa_pairwise
  rsn_pairwise
  wpa_passphrase
  wpa_psk

The specified configuration parameter is copied from the source
interface to the destination interface. The main use for this is to
allow cloning of security configuration without having to expose the
keys from the hostapd process.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-21 13:42:16 +03:00
Anton Nayshtut
c497a024a2 hostapd: Introduce hostapd_ctrl_iface_get_key_mgmt()
This function will be used in DUP_NETWORK command implementation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-21 13:33:21 +03:00
Anton Nayshtut
b328145296 hostapd: Introduce hostapd_interfaces_get_hapd()
This function will be used in DUP_NETWORK command implementation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-21 13:24:36 +03:00
Jouni Malinen
3188aabaf1 Add shared periodic cleanup function for AP mode
This new mechanism can be used to combine multiple periodic AP
(including P2P GO) task into a single eloop timeout to minimize number
of wakeups for the process. hostapd gets its own periodic caller and
wpa_supplicant uses the previously added timer to trigger these calls.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-20 13:33:30 +03:00
Jouni Malinen
3dfaedb433 hlr_auc_gw: Hide a bogus static analyzer warning
For some reason, snprintf() was not seen as sufficient to remove
potentially tainted string from fgets() before passing this to rename().
This does not make much sense, but anyway, try to get rid of the warning
by using a separate buffer for the internally written file names.
(CID 72690)

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-07-18 22:55:02 +03:00
Mohammed Shafi Shajakhan
de7581ef68 hostapd: Add current wpa parameter into GET_CONFIG output
This can be used, e.g., by an action script to update new WPS
settings for the AP.

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
2015-07-18 00:17:34 +03:00
Mohammed Shafi Shajakhan
b8e5426dad hostapd_cli: Allow PID file to be specified
This can help when running multiple hostapd_cli instances
per interface and need to kill them correspondingly.

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
2015-07-18 00:15:36 +03:00
Vivek Natarajan
442ffc51ac hostapd: Extend the sounding and BF steering capabilities
Depending on the number of antennas, the txbf sounding
and steering capabilites need to be extended.

Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
2015-07-17 23:58:15 +03:00
Jouni Malinen
780753fab2 FST: Clear hostapd fst_ies on FST-DETACH to avoid use of freed memory
This is needed in the corner case of FST-DETACH being used without
stopping the AP instance.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-17 16:29:20 +03:00
Jouni Malinen
898a9790ad Document hostapd ft_over_ds configuration parameter
This had been forgotten from hostapd.conf.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-17 11:16:15 +03:00
Anton Nayshtut
6990d41a74 hostapd: Add global to local control interface redirection
This patch implements global to local control interface redirection in
the same way as it's done for wpa_supplicant. Any global control
interface command beginning with "IFNAME=..." will be routed to the
corresponding local control interface handler.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-16 20:21:18 +03:00
Anton Nayshtut
585478e2b9 hostapd: Add hostapd_ctrl_iface_receive_process()
The newly introduced function will be used in followup commits to handle
requests redirected from the global control interface.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-16 20:21:00 +03:00
Anton Nayshtut
a8dab08a28 FST: Testing support
This patch introduces infrastructure needed for FST module tests.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-16 18:26:16 +03:00
Anton Nayshtut
ee03910777 FST: Add hostapd_cli fst command
This can be used to issue FST-MANAGER control interface commands.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-16 18:26:15 +03:00
Anton Nayshtut
8cf53ec9f7 FST: Add build rules for hostapd
This patch integrates the FST into the hostapd.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-16 18:26:15 +03:00
Anton Nayshtut
8e9a8b0f8c FST: hostapd control interface
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-16 18:26:15 +03:00
Anton Nayshtut
6959145b86 FST: Integration into hostapd
This commit integrates the FST into the hostapd.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-16 18:26:15 +03:00
Anton Nayshtut
104bef453b FST: hostapd configuration parameters
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-16 18:26:15 +03:00
Anton Nayshtut
ee1e3f57b5 hostapd: Global control interface notifications
This commit implements hostapd global control interface notifications
infrastructure. hostapd global control interface clients issue
ATTACH/DETACH commands to register and deregister with hostapd
correspondingly - the same way as for any other hostapd/wpa_supplicant
control interface.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-16 12:33:29 +03:00
Jouni Malinen
3722c0f4aa Add EAPOL_SET hostapd command to configure EAPOL parameters
This new control interface command "EAPOL_REAUTH <MAC address>
<parameter> <value>" can be used to implement the IEEE 802.1X PAE
Set Authenticator Configuration operation.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-07-12 11:34:18 +03:00
Jouni Malinen
cfb5c08f21 Add EAPOL_REAUTH hostapd command to trigger EAPOL reauthentication
This new control interface command "EAPOL_REAUTH <MAC address>" can be
used to implement the IEEE 802.1X PAE Reauthenticate operation.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-07-12 11:33:33 +03:00
Jouni Malinen
66f1e078e7 DATA_TEST_TX: Avoid ubsan warning on 0x80<<24 not fitting in int
Use unsigned constant instead of signed to avoid warning with the LSB
being set in an int.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-07-07 16:25:06 +03:00
Jouni Malinen
75352270fa Avoid misaligned IPv4 header accesses in DATA_TEST_* commands
The IPv4 header after the Ethernet header is not 32-bit aligned and the
previous version ended up accessing 32-bit members at misaligned
addresses.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-07-07 16:25:06 +03:00
Jouni Malinen
2da525651d Add backtrace-based error path testing mechanism
The new TEST_FAIL and GET_FAIL control interface commands can be used
similarly to the earlier TEST_ALLOC_FAIL/GET_ALLOC_FAIL design. The new
version is more generic framework allowing any function to be annotated
for failure testing with the TEST_FAIL() macro. This mechanism is only
available in builds with CONFIG_WPA_TRACE_BFD=y and
CONFIG_TESTING_OPTIONS=y. For other builds, the TEST_FAIL() macro is
defined to return 0 to allow the compiler to remove the test code from
normal production builds.

As the first test site, allow os_get_random() to be marked for failing
based on call backtrace.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-06-29 23:23:56 +03:00
Jouni Malinen
6c7314917b AP: Increase maximum value accepted for cwmin/cwmax
The cwmin/cwmax parameters were limited more than is needed. Allow the
full range (0..15 for wmm_ac_??_{cwmin,cwmax} and 1..32767 for
tx_queue_data?_{cwmin,cwmax}) to be used.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-06-27 23:34:49 +03:00
Kevin Cernekee
a1407217b1 Android: Rename ANDROID_P2P_STUB to ANDROID_LIB_STUB
If BOARD_HOSTAPD_PRIVATE_LIB is not used on an Android build, we will
need to replace both the p2p functions *and* wpa_driver_nl80211_driver_cmd
in order to successfully link.  Let's make the name more generic so it is
more obvious what it is used for.

Suggested-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Kevin Cernekee <cernekee@google.com>
2015-06-26 22:46:16 +03:00
Jouni Malinen
b4c0f58452 Clear allocated debug message buffers explicitly
When hostapd or wpa_supplicant is run in debug more with key material
prints allowed (-K on the command line), it is possible for passwords
and keying material to show up in debug prints. Since some of the debug
cases end up allocating a temporary buffer from the heap for processing
purposes, a copy of such password may remain in heap. Clear these
temporary buffers explicitly to avoid causing issues for hwsim test
cases that verify contents of memory against unexpected keys.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-06-17 16:30:34 +03:00
Jouni Malinen
995a3a06f4 Document the wpa_msg_cb "global" parameter
Instead of an int variable with magic values 0, 1, 2, use an enum that
gives clearer meaning to the values now that the original boolean type
global argument is not really a boolean anymore.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-06-10 16:02:00 +03:00
Jouni Malinen
ee120ff381 Remove [MU-BEAMFORMEE] option from hostapd vht_capab parameter
The standard hardcodes the MU Beamformee Capable subfield is hardcoded
to 0 when transmitting by an AP, so there is no need to provide a
configuration parameter for setting this to one.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-06-10 13:41:54 +03:00
Jouni Malinen
c5ee4dd9d9 Fix spelling of initialize in a comment and an error message
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-06-10 12:02:46 +03:00
Peng Xu
3784c0589e Extend hw_mode to support any band for offloaded ACS case
When device supports dual band operations with offloaded ACS, hw_mode
can now be set to any band (hw_mode=any) in order to allow ACS to select
the best channel from any band. After a channel is selected, the hw_mode
is updated for hostapd.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-05-27 12:17:57 +03:00
Jouni Malinen
7f2f3a67d2 Increase DH key size in the hostapd.conf example
OpenSSL is moving to use 2048-bit DH key size as the default with
dhparam. Increase the value in the hostapd.conf to match that to reduce
likelihood of ending up using a shorter key.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-05-24 10:47:21 +03:00
Hamad Kadmany
01a025937c WPS: Add support for 60 GHz band
Handling of WPS RF band for 60 GHz was missing. Add it in all relevant
places and also map "AES" as the cipher to GCMP instead of CCMP when
operating on the 60 GHz band.

Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
2015-04-28 00:22:16 +03:00
Jouni Malinen
4a7ce98469 Make IPv6 NA multicast-to-unicast conversion configurable
This can be used with Proxy ARP to allow multicast NAs to be forwarded
to associated STAs using link layer unicast delivery. This used to be
hardcoded to be enabled, but it is now disabled by default and can be
enabled with na_mcast_to_ucast=1. This functionality may not be desired
in all networks and most cases work without it, so the new
default-to-disabled is more appropriate.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-27 12:30:09 +03:00
Mikael Kanstrup
8b423edbd3 Declare all read only data structures as const
By analysing objdump output some read only structures were found in
.data section. To help compiler further optimize code declare these
as const.

Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
2015-04-25 17:33:06 +03:00
Jouni Malinen
81847c22ba Replace HOSTAPD_MAX_SSID_LEN with SSID_MAX_LEN
This makes source code more consistent.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-22 11:44:18 +03:00
Jouni Malinen
d9d1b9527a Use SSID_MAX_LEN define instead of value 32 when comparing SSID length
This makes the implementation easier to understand.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-22 11:44:18 +03:00
Jouni Malinen
cc6f24380c Add WPS_DEV_NAME_MAX_LEN define and use it when comparing length
This make code easier to understand.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-22 11:44:18 +03:00
Jouni Malinen
6812782462 hlr_auc_gw: Allow Milenage RES length to be reduced
Some USIM use shorter RES length than the 64-bit default from Milenage.
Such cases did not interoperate with the hlr_auc_gw implementation. Make
it possible to configure the RES length 4..8 octets, i.e., 32 to 64
bits) to support such USIM.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-04-03 12:44:03 +03:00
Eliad Peller
154a1d5f7f hostapd: Fix some compilation errors
If NEED_AP_MLME=y is not defined, compilation might
fail under some configurations:

src/ap/drv_callbacks.c:594:2: warning: implicit declaration of
function ‘hostapd_acs_completed’ [-Wimplicit-function-declaration]

src/ap/sta_info.c:253: undefined reference to `sae_clear_retransmit_timer'

Fix these errors by adding the missing hostapd_acs_completed() stub,
and defining NEED_AP_MLME in case of CONFIG_SAE.

Signed-off-by: Eliad Peller <eliad@wizery.com>
2015-03-29 20:51:14 +03:00
Jouni Malinen
65a7b21f5e OpenSSL: Implement AES-128 CBC using EVP API
This replaces the internal CBC mode implementation in
aes_128_cbc_encrypt() and aes_128_cbc_decrypt() with the OpenSSL
implementation for CONFIG_TLS=openssl builds.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-29 20:30:58 +03:00
Ben Greear
c469d6228d Error out if user configures SQLite DB without CONFIG_SQLITE
This should make it more obvious to users that they have a fatal
configuration problem in hostapd authentication server.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2015-03-28 13:11:05 +02:00
Manikandan Mohan
857d94225a Extend offloaded ACS QCA vendor command to support VHT
Update ACS driver offload feature for VHT configuration. In addition,
this allows the chanlist parameter to be used to specify which channels
are included as options for the offloaded ACS case.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-23 12:18:05 +02:00
Jouni Malinen
58e115b869 Fix hlr_auc_gw build with OpenSSL
Commit 983c6a606b ('OpenSSL: Replace
internal HMAC-MD5 implementation') forgot to make inclusion of md5.o
conditional for hlr_auc_gw build.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-20 15:56:59 +02:00
Jouni Malinen
6784168d07 Remove SChannel support
SChannel/CryptoAPI as a TLS/crypto library alternative was never
completed. Critical functionality is missing and there are bugs in this
implementation. Since there are no known plans of completing this
support, it is better to remove this code.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-18 22:31:36 +02:00
Jouni Malinen
bc1d23ae1d Add ChangeLog entries for v2.4
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-14 16:51:02 +02:00
Jouni Malinen
9836cb5387 Add option to force a specific RADIUS client address to be used
The new hostapd.conf parameter radius_client_addr can now be used to
select a specific local IP address to be used as the RADIUS client
address.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 22:36:52 +02:00
Jouni Malinen
bbee36e316 Allow RADIUS server address to be replaced
The new hostapd parameters auth_server_addr_replace and
acct_server_addr_replace can now be used to replace the configured IP
address instead of adding a new RADIUS server. This is mainly useful for
testing purposes where the address can be changed over control interface
during AP operation.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-28 15:45:16 +02:00
Stefan Tomanek
891dfb3336 Add helper function to clear and free wpa_psk list
This change adds the function hostapd_config_clear_wpa_psk() that
deletes an entire wpa_psk structure, making sure to follow the linked
list and to free the allocated memory of each PSK node. This helps to
prevent memory leaks when using PSKs from multiple sources and
reconfiguring the AP during runtime.

Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
2015-02-21 17:11:15 +02:00
Jouni Malinen
9ff8dda12f Add hostapd UPDATE_BEACON ctrl_iface command
This can be used to ask Beacon frames to be updated explicitly, e.g.,
after a dynamic configuration parameter change. This can also be used to
start beaconing on an interface that was started with start_disabled=1.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-09 19:56:32 +02:00
Jouni Malinen
99650cadc9 Add STOP_AP control interface command
This is mainly for testing purposes to allow beaconing to be stopped
without clearing AP state in hostapd.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-08 13:35:49 +02:00
Jouni Malinen
68fa00c341 ACS: Allow specific channels to be preferred
The new acs_chan_bias configuration parameter is a space-separated list
of <channel>:<bias> pairs. It can be used to increase (or decrease) the
likelihood of a specific channel to be selected by the ACS algorithm.
The total interference factor for each channel gets multiplied by the
specified bias value before finding the channel with the lowest value.
In other words, values between 0.0 and 1.0 can be used to make a channel
more likely to be picked while values larger than 1.0 make the specified
channel less likely to be picked. This can be used, e.g., to prefer the
commonly used 2.4 GHz band channels 1, 6, and 11 (which is the default
behavior on 2.4 GHz band if no acs_chan_bias parameter is specified).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-06 17:59:57 +02:00
Jouni Malinen
d2ca6baa56 Fix hostapd obss_interval documentation
This parameter has been available for more than just testing purposes,
i.e., OBSS scanning has already been used to enable 20-to-40 MHz channel
changes on 2.4 GHz.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 12:32:37 +02:00
Roger Zanoni
b42f539ed2 Add a variable to handle extra CFLAGS values
Some packages don't install its headers in the default directory
(e.g.: In Arch Linux libiberty and libn13 includes are installed)
in their own subdirectory under /usr/include) and the build fails
trying to find the headers.

This patch will allow passing extra CFLAGS values without discarding
the assignments made in the Makefile. The CFLAGS values in the Makefile
are ignored, if defined directly in the make command line.

Signed-off-by: Roger Zanoni <roger.zanoni@openbossa.org>
2015-02-01 00:26:17 +02:00
Jouni Malinen
4437f8fc77 Free old eap_user_file data on configuration change
This fixes a memory leak if hostapd eap_user_file parameter is modified.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-30 00:54:40 +02:00
Jouni Malinen
f19c907822 OpenSSL: Implement aes_wrap() and aes_unwrap()
This replaces the implementation in aes-wrap.c and aes-unwrap.c with
OpenSSL AES_wrap_key() and AES_unwrap_key() functions when building
hostapd or wpa_supplicant with OpenSSL.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-28 13:09:31 +02:00
Jouni Malinen
983c6a606b OpenSSL: Replace internal HMAC-MD5 implementation
Use OpenSSL HMAC_* functions to implement HMAC-MD5 instead of depending
on the src/crypto/md5.c implementation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-28 13:09:31 +02:00
Jouni Malinen
937403b581 Update copyright notices for the new year 2015
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-27 01:43:55 +02:00
Jouni Malinen
5e3b5197cc Add Suite B 192-bit AKM
WPA-EAP-SUITE-B-192 can now be used to select 192-bit level Suite B into
use as the key management method.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-27 01:43:52 +02:00
Jouni Malinen
97ae35a848 Add HMAC-SHA384
For now, this is only implemented with OpenSSL.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-27 01:26:51 +02:00
Adrien Decostre
1648cc6427 ACS: Allow subset of channels to be configured
Add the possibility to define a subset of channels used by the ACS
engine when not operating on DFS channels.

Signed-off-by: Adrien Decostre <ad.decostre@gmail.com>
2015-01-19 02:35:43 +02:00
Yanbo Li
e7d0e97bdb hostapd: Add vendor specific VHT extension for the 2.4 GHz band
This allows vendor specific information element to be used to advertise
support for VHT on 2.4 GHz band. In practice, this is used to enable use
of 256 QAM rates (VHT-MCS 8 and 9) on 2.4 GHz band.

This functionality is disabled by default, but can be enabled with
vendor_vht=1 parameter in hostapd.conf if the driver advertises support
for VHT on either 2.4 or 5 GHz bands.

Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
2015-01-14 00:59:22 +02:00
Jouni Malinen
a16514516b Add "GET tls_library" to provide information on TLS library and version
This new wpa_supplicant and hostapd control interface command can be
used to determine which TLS library is used in the build and what is the
version of that library.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-12 00:19:21 +02:00
Jouni Malinen
0b402479bf Remove Network Security Service (NSS) support
NSS as a TLS/crypto library alternative was never completed and this
barely functional code does not even build with the current NSS version.
Taken into account that there has not been much interest in working on
this crypto wrapper over the years, it is better to just remove this
code rather than try to get it into somewhat more functional state.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-11 00:58:10 +02:00
Janusz Dziedzic
269dfe232b Introduce common hw features
Introduce wpa_supplicant/hostapd hw features.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2015-01-10 17:35:53 +02:00
Jouni Malinen
86a7fbb2c1 Verify that eloop_register_read_sock() succeeds for ctrl_iface setup
This allows faster detection of a case where a memory allocation fails
within eloop.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-08 02:34:08 +02:00
Jouni Malinen
a156ffda61 Add support for testing memory allocation failures
The new control interface command TEST_ALLOC_FAIL and GET_ALLOC_FAIL can
now be used to trigger memory allocation failures for testing purposes.
TEST_ALLOC_FAIL sets a failure conditions with
<count>:func[;func][;func]... string and GET_ALLOC_FAIL returns the
current state using the same format. Whenever an allocation is made with
a matching backtrace of calling functions, the count is decremented by
one and once zero is reached, the allocation is forced to fail.

Function names can be prefixed with either '=' or '?' to get different
matching behavior. '=' requires this specific function to be the next
one in the backtrace (i.e., do not skip any other functions in the list
which is the default behavior). '?' allows the function to be optionally
present in the backtrace.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-07 13:19:43 +02:00
Jouni Malinen
77a2c3941e crypto: Clear temporary heap allocations before freeing
This reduces the time private keys may remain in heap memory after use.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-06 02:49:13 +02:00
Paul Stewart
de27bc7673 hostapd: Set stdout line-buffered
If hostapd will use stdout for debugging, set stdout to be line
buffered in case its output is redirected to a file. This allows
incremental output to be viewed immediately instead of at the file
buffering interval.

Signed-hostap: Paul Stewart <pstew@chromium.org>
2014-12-29 15:49:05 +02:00
Jouni Malinen
010fa245bd Add QUIET=1 option for make
This can be used to reduce verbosity for build messages.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-29 15:49:05 +02:00
Jouni Malinen
a193231dfb Clean up debug prints to use wpa_printf()
This converts most of the remaining perror() and printf() calls from
hostapd and wpa_supplicant to use wpa_printf().

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-26 13:20:57 +02:00
Prashanth Bhatta
9108ea09f2 hostapd: Make install path configurable
Makefile always installs to /usr/local/bin and on some platforms,
/usr/local/bin is not in default search path. Modify the Makefile such
that bin path can be configurable so that build system can pass
appropriate path for installation. If bin path is not specified then by
default binaries are installed in /usr/local/bin.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-19 12:32:50 +02:00
Jouni Malinen
2c6411edd0 ERP: Add ERP_FLUSH for hostapd
This can be used to drop any pending ERP key from both the internal AP
authentication server and RADIUS server use of hostapd.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-14 15:47:04 +02:00
Jouni Malinen
0629eeb490 RRM: Add AP mode minimal advertisement support for testing
The new hostapd.conf radio_measurements parameter can now be used to
configure a test build to advertise support for radio measurements with
neighbor report enabled. There is no real functionality that would
actually process the request, i.e., this only for the purpose of minimal
STA side testing for now.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-12 20:45:31 +02:00
Jouni Malinen
eeab4f2fda Check os_snprintf() result more consistently - automatic 3
This converts os_snprintf() result validation cases to use
os_snprintf_error() where the comparison was 'res > size' instead of
'res >= size - 1'. These changes were done automatically with spatch
using the following semantic patch:

@@
identifier E1;
expression E2,E3,E4,E5,E6;
statement S1;
@@

(
  E1 = os_snprintf(E2, E3, ...);
|
  int E1 = os_snprintf(E2, E3, ...);
|
  if (E5)
	E1 = os_snprintf(E2, E3, ...);
  else
	E1 = os_snprintf(E2, E3, ...);
|
  if (E5)
	E1 = os_snprintf(E2, E3, ...);
  else if (E6)
	E1 = os_snprintf(E2, E3, ...);
  else
	E1 = 0;
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	return -1;
  }
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else if (E6) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	return -1;
  }
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	E1 = os_snprintf(E2, E3, ...);
  }
)
? os_free(E4);
- if (E1 < 0 || (size_t) E1 >= E3 - 1)
+ if (os_snprintf_error(E3, E1))
(
  S1
|
{ ... }
)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
d85e1fc8a5 Check os_snprintf() result more consistently - automatic 1
This converts os_snprintf() result validation cases to use
os_snprintf_error() where the exact rule used in os_snprintf_error() was
used. These changes were done automatically with spatch using the
following semantic patch:

@@
identifier E1;
expression E2,E3,E4,E5,E6;
statement S1;
@@

(
  E1 = os_snprintf(E2, E3, ...);
|
  int E1 = os_snprintf(E2, E3, ...);
|
  if (E5)
	E1 = os_snprintf(E2, E3, ...);
  else
	E1 = os_snprintf(E2, E3, ...);
|
  if (E5)
	E1 = os_snprintf(E2, E3, ...);
  else if (E6)
	E1 = os_snprintf(E2, E3, ...);
  else
	E1 = 0;
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	return -1;
  }
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else if (E6) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	return -1;
  }
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	E1 = os_snprintf(E2, E3, ...);
  }
)
? os_free(E4);
- if (E1 < 0 || \( E1 >= E3 \| (size_t) E1 >= E3 \| (unsigned int) E1 >= E3 \| E1 >= (int) E3 \))
+ if (os_snprintf_error(E3, E1))
(
  S1
|
{ ... }
)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
d3bddd8b84 ERP: Add support for ERP on EAP server and authenticator
Derive rRK and rIK on EAP server if ERP is enabled and use these keys to
allow EAP re-authentication to be used and to derive rMSK.

The new hostapd configuration parameter eap_server_erp=1 can now be used
to configure the integrated EAP server to derive EMSK, rRK, and rIK at
the successful completion of an EAP authentication method. This
functionality is not included in the default build and can be enabled
with CONFIG_ERP=y.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-04 12:16:27 +02:00
Jouni Malinen
2a5156a66c ERP: Add optional EAP-Initiate/Re-auth-Start transmission
hostapd can now be configured to transmit EAP-Initiate/Re-auth-Start
before EAP-Request/Identity to try to initiate ERP. This is disabled by
default and can be enabled with erp_send_reauth_start=1 and optional
erp_reauth_start_domain=<domain>.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-04 12:08:56 +02:00
Jouni Malinen
0ecff8d7c3 Add hostapd driver_params config parameter
This is mainly for development testing purposes to allow driver_nl80211
behavior to be modified.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-29 13:24:42 +02:00
Jouni Malinen
ebd557288c Remove forgotten driver_test.c variables
hostapd was still providing couple of parameters that were used only in
the already removed driver_test.c framework.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-29 12:49:55 +02:00
Jouni Malinen
85660d312a Add DATA_TEST_FRAME for testing Data frame processing on AP side
The new hostapd control interface command can be used in automated
testing to verify how AP processes Data frames with arbitrary contents.
This is enabled only in builds with CONFIG_TESTING_OPTIONS=y.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-28 22:37:05 +02:00
Jouni Malinen
527d2378ac hostapd: Allow DATA_TEST_CONFIG to configure ifname
This allows the device-based data connectivity tests to be extended for
bridge and VLAN interface cases.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 14:02:18 +02:00