The ap_beacon_rate_* test cases could end up terminating before the very
first Beacon frame is captured, so wait a bit after the connection to
make sure at least one Beacon frame is going to be in the capture file.
Signed-off-by: Jouni Malinen <j@w1.fi>
WEP should not be used for anything anymore. As a step towards removing
it completely, move all WEP related functionality to be within
CONFIG_WEP blocks. This will be included in builds only if CONFIG_WEP=y
is explicitly set in build configuration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Replace the hardcoded /tmp filenames for generated ACL and BSS
configuration files with proper temporary files from tempfile.mkstemp()
to avoid conflicts with existing files or with parallel uses. Remove ACL
files from the local directory at the end of each test case. BSS files
are currently left behind, but can be cleaned up separately if needed
for non-VM testing (VM testing has those on ramdrive so they get dropped
automatically at the end) and for remote devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
Generate ACL files instead of using files with hardcoded values for the
STA MAC addresses. Send the generated files also to the remote client if
required.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Use a helper function to perform this common sequence to disconnect and
stop any possibly started reconnection attempt.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the ABORT_SCAN command succeeds, CTRL-EVENT-SCAN-RESULTS event is
delivered for the aborted scan. Following this with an immediate
flush_scan_cache() call can result in the first scan interpreting that
pending event as the completion and that results in trying to start
another scan while the first scan is still in progress.
Signed-off-by: Jouni Malinen <j@w1.fi>
The configurated fragmentation/RTS threshold value survives AP mode
interface restarts, so these values need to be explicitly cleared back
to default (disabled). This fixes an issue where some test cases could
not work correctly if fragmentation on the interface was enabled. For
example, this combination used to fail:
ap_fragmentation_open ap_hs20_fetch_osu
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The Linux kernel commit 113f3aaa81bd ("cfg80211: Prevent regulatory
restore during STA disconnect in concurrent interfaces") broke the
regulatory clearing attempt in many test cases since
cfg80211_is_all_idle() is now returning false due to the AP interface
being up and that results in the Country IE -based regulatory
information not getting cleared back to defaults.
Work around this by stopping the AP interface first so that when the
station interface receives the disconnection, there are no other active
interfaces in the system. In addition, wait for REGDOM event for the
Country IE hint after association to avoid disconnection before the
regulatory events have been fully processed.
Signed-off-by: Jouni Malinen <j@w1.fi>
In ap_acl_deny test, the AP doesn't send probe responses during scan due
to ACL reject. As the result, dev[0] might miss the AP's Beacon frame
because the dwell time is too short. Make the test more robust and
trigger passive scan, and by that increase the probability of hearing
the AP.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
HT cannot be used with WEP-only network, so don't try to do that here.
This get rids of some unnecessary Beacon frame updates during
disassociation/association and can make the test case a bit more robust.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the ap_wds_sta test case to cover post-reassociation case
(both with and without Authentication frame exchange) and add similar
test cases to cover open and WEP cases in addition to this existing
WPA2-PSK test case.
These cover functionality testing for the previous fix in
reassociation-without-new-authentication case. In addition, these find a
new mac80211 issue for the WEP + 4addr combination.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
After successfully passing the 525 tests on a remote setup mark the
tests as remote compatible.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
The hwsim tests used to execute shell commands in the tests using the
subprocess python module. Use the cmd_execute() general function for
executing shell commands to setup bridge so that this would also work on
remote setups.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
The hwsim tests used to execute shell commands in the tests using the
subprocess python module. Use the cmd_execute() general function for
executing "iw reg set 00" so that this would also work on remote setups.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (1) converts the cases where apdev[#]['ifname'] was used as
the argument to hostapd.add_ap().
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
It was possible for the AP's Beacon frame to be seen by dev[0] when
running a scan. This is not an error case. Make this test case more
robust by verifying with a sniffer whether a Probe Response frame was
sent to unexpected STA.
Signed-off-by: Jouni Malinen <j@w1.fi>
run-tests.py is running as root, so sudo does not need to be used
anymore from within each test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for regulatory domain changes to "leak" into following
test cases in number of cases where the cfg80211 BSS table remained
after regulatory domain had been restored to world roaming. Try to make
this less likely to occur by explicitly clearing BSS table at the end of
test cases that use different regulatory domain. This makes P2P test
cases that verify channel selection based on world roaming rules more
robust.
Signed-off-by: Jouni Malinen <j@w1.fi>
External tool is not needed anymore to run the data connectivity tests
since hostapd test mode now allows the possible bridge or VLAN interface
to be specified.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to replace data connectivity testing to use
something else than local hwsim_test binary on the controller device.
Signed-off-by: Jouni Malinen <j@w1.fi>
