These channels were already enabled for P2P use, but the local
configuration parameter was not allowed to use the operating class in
which the 40 MHz channels are specified.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 50178335bf introduced a regression
for P2P-GROUP-STARTED event indication during p2p_connect-join when
using a separate P2P group interface. wpa_s->global->p2p_group_formation
was already set in that case to point to the group interface and this
commit changed this to point to incorrect interface. Fix this by setting
p2p_group_formation here only in case a separate group interface is not
used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit bb4d4deb4b introduced a code path
that could potentially end up calling wpa_config_update_psk() with NULL
passphrase. While that may not happen in practice, it is better to make
sure it doesn't happen since that function will dereference the
passphrase pointer unconditionally.
Signed-hostap: Jouni Malinen <j@w1.fi>
This continues optimizations for use of CPU heavy pbkdf2_sha1() in GO
setup after the earlier commit 30c371e8a5
by allowing PSK to be used instead of passphrase when creating
persistent group information manually for the GO.
It should be noted that this would not meet the requirements in the P2P
specification (GO shall maintain the passphrase), so this should be used
only when there is no need to allow manual configuration of legacy STAs
using the passphrase.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
cfg80211 caches the scan results according the channel number. Due to
the 15 sec aging this might cause the user mode to see more than one
scan result with the same BSSID, e.g. - one scan result for the
P2P Device and one for the P2P GO (once it's enabled).
Fix this by updating the device entry only if the new peer entry is
newer than the one previously stored.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-hostap: Arik Nemtsov <arik@wizery.com>
There is no need for p2p_supplicant.c to access wpa_s->pending_action_tx
so move these references to offchannel.c to get a bit cleaner interface
between the components.
Signed-hostap: Jouni Malinen <j@w1.fi>
p2p_cancel did not properly cancel a pending p2p_connect-join operation.
Address the different steps in that process: initial scan, Provision
Discovery exchange before connection, and WPS provisioning step
(including the scans before WPS).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The PD Request retry limit can be used to achieve the same behavior,
so drop this duplicated timeout mechanism and control the timeout
based on MAX_PROV_DISC_REQ_RETRIES.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The GO may be in sleep when we send a PD Request frame to indicate that
we are about to join a running group. Previously, this frame was not
retried more than normal low level retries. This can result in the GO
not getting the frame especially in cases where concurrent multi-channel
operations or aggressive sleep schedule is used since most drivers do
not yet synchronize with the GO's NoA before association.
Increase the likelihood of the GO receiving the PD Request frame by
retransmitting it similarly to the PD-for-GO-Negotiation case. Start
the actual join operation only after these retries have failed to get
an acknowledgment from the GO to give the connection attempt a chance
to succeed if the driver implements better NoA synchronization for it.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_prov_disc_req() used the join parameter to figure out whether the PD
request was a user initiated or not. This does not cover all use cases
of PD, so add a separate parameter to allow caller to indicate whether
the user requested the operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If separate group interfaces are used, the pending group interface got
removed unnecessarily when stopping find operations when accepting an
invitation to reinvoke the group in GO role. This resulted in the group
interfaces getting created twice. Avoid this unnecessary extra operation
by skipping removal of the pending interface in the reinvocation
sequence.
Signed-hostap: Jouni Malinen <j@w1.fi>
The PSK generation done by pbkdf2_sha1() is one of the longest CPU time
users according to our profiling from boot to GO started.
So I have reduced some steps.
I could boot a GO by this command sequence.
-------------
add_net
set_network 0 ssid '"DIRECT-XX"'
set_network 0 psk
'"123456789012345678901234567890123456789012345678901234567890123"'
set_network 0 proto RSN
set_network 0 key_mgmt WPA-PSK
set_network 0 pairwise CCMP
set_network 0 auth_alg OPEN
set_network 0 mode 3
set_network 0 disabled 2
p2p_group_add persistent=0 freq=2412
-------------
By this sequence, pbkdf2_sha1() was called three times and the function
calculates the same value each time. Reduce number of calls to
pbkdf2_sha1() from 3 to 1 by caching the previous result.
Signed-hostap: Masashi Honma <masashi.honma at gmail.com>
The DNS Name is allowed to use or not use domain name compression. To
handle both cases, check human readable DNS Name match if binary
matching does not show a hit.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There may be multiple Bonjour PTR matches for the same key, so extend
the P2P SD code for this to allow such entries to be added (i.e., do not
override previously added value, but add a new one). Similarly, return
multiple matches (one per Service TLV) for a query if it happens to
match more than a single configured Bonjour service.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new P2P_SET parameter disc_int can now be used to configure
discoverable interval for p2p_find operations. The format of the command
for setting the values is "P2P_SET disc_int <minDiscoverableInterval>
<maxDiscoverableInterval> <max TUs for discoverable interval>". The
first two parameters are given in units of 100 TUs (102.4 ms). The third
parameter can be used to further limit the interval into a specific TU
amount. If it is set to -1, no such additional limitation is enforced.
It should be noted that the P2P specification describes the random
Listen state interval to be in units of 100 TUs, so setting the max TU
value to anything else than -1 is not compliant with the specification
and should not be used in normal cases. The default parameters can be
set with "P2P_SET disc_int 1 3 -1".
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpas_p2p_pd_before_join_timeout() needs to clear the
pending_pd_before_join flag to match other uses of this flag prior to
calling wpas_p2p_join_start(). Without this, the flag could be left set
which can cause following P2P operations to behave in unexpected ways.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new p2p_no_group_iface=1 configuration parameter can now be used to
disable the default behavior of adding a separate interface for the P2P
group when driver support for concurrent interfaces is available.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 0d30cc240f forced
wpa_s->current_ssid to be cleared in wpa_supplicant_mark_disassoc()
which gets called from wpa_supplicant_event_disassoc(). This breaks the
P2P group idle mechanism for the case where p2p_group_idle is not set
(i.e., is the default 0) since wpas_p2p_group_idle_timeout() ignores the
timeout in that case if the interface is not recognized as a client
interface (which was based on wpa_s->current_ssid being set).
Fix this by making wpas_p2p_is_client() default to client case if
wpa_s->current_ssid is NULL. This is much more likely case since the P2P
GO mode operation would not really clear the pointer without explicit
request to disconnect.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the driver indicates support for multi-channel concurrency, change
the p2p_connect behavior to not force the current operating channel, but
instead, just mark it as preferred for GO Negotiation. This change
applies only for the case when the freq parameter is not used with the
p2p_connect command.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
P2P includes two use cases where one of the devices is going to start a
group and likely change channels immediately after processing a frame.
This operation may be fast enough to make the device leave the current
channel before the peer has completed layer 2 retransmission of the
frame in case the ctrl::ack frame was lost. This can result in the peer
not getting TX status success notification.
For GO Negotiation Confirm frame, p2p_go_neg_conf_cb() has a workaround
that ignores the TX status failure and will continue with the group
formation with the assumption that the peer actually received the frame
even though we did not receive ctrl::ack. For Invitation Response frame
to re-invoke a persistent group, no such workaround is used in
p2p_invitation_resp_cb(). Consequently, TX status failure due to lost
ctrl::ack frame results in one of the peers not starting the group.
Increase the likelihood of layer 2 retransmission getting acknowledged
and ctrl::ack being received by waiting a short duration after having
processed the GO Negotiation Confirm and Invitation Response frames for
the re-invocation case. For the former, use 20 ms wait since this case
has been worked around in deployed devices. For the latter, use 50 ms
wait to get even higher likelihood of getting ctrl::ack through since
deployed devices (and the current wpa_supplicant implementation) do not
have a workaround to ignore TX status failure.
20 ms is long enough to include at least couple of retries and that
should increase likelihood of getting ctrl::ack through quite a bit. The
longer 50 ms wait is likely to include full set of layer 2 retries.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the wpa_cli wps_pin command to support specification of the PIN
expiration time in seconds similarly to hostapd_cli wps_pin command when
using wpa_supplicant for AP mode (including P2P GO).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If wpa_s->current_ssid is not set (e.g., after disconnection that
did not result in immediate group removal), an incorrect group could
have been removed since the network block iteration here could select
the network block that is used to store persistent group credentials.
Fix this by verifying that disabled != 2 to avoid picking the network
block that could not have been the temporary P2P group.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The wpa_s->p2p_in_provisioning flag did not get cleared in some cases
where p2p_cancel command is used to stop group formation. This can result
in some operations (like p2p_find) failing afterwards. Fix this by using
wpas_group_formation_completed() when processing p2p_cancel for a group
that has not yet completed group formation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for the P2P client group to be removed while waiting for
a pending scan operation (e.g., when p2p_group_idle timeout hits after
getting disconnected from the GO with something else than
Deauthentication with reason code 3). If this happens with a P2P
interface that is used both for P2P Device and group roles, scan state
could get stuck while waiting for the next scan to complete since no
more station (P2P client) mode scans are scheduled. Fix this by clearing
sta_scan_pending when removing the temporary group network block.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Make Invitation process for re-invoking a persistent group behave
similarly to GO Negotiation as far as channel negotiation is concerned.
The Operating Channel value (if present) is used as a starting point if
the local device does not have a forced operating channel (e.g., due to
concurrent use). Channel lists from devices are then compared to check
that the selected channel is in the intersection. If not, channel is
selected based on GO Negotiation channel rules (best channel preferences
etc.). Invitation Request is rejected if no common channel can be
selected.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Setting just ssid->passphrase is not enough to complete the network
block for the GO entry. Also the PSK needs to be derived so that the
network is considered enabled by wpas_network_disabled(). The previous
version worked as long as something else allowed the scan request to be
performed (this is needed even though the actual scan is skipped when
starting GO).
The first GO start was allowed because wpa_s->scan_req is initialized to
1 in wpa_supplicant_alloc(). However, other attempts may fail if
wpa_s->scan_req is cleared. This failure shows up as "No enabled
networkas - do not scan" in debug log followed by state change to
INACTIVE when trying to start GO.
Fix this by deriving PSK from the passphrase for GO mode.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 30ee769235 started skipping P2P
group removal if wpa_s->current_ssid is not set and commit
0d30cc240f started clearing
wpa_s->current_ssid on disconnection. This combination broke
p2p_group_idle timeout on P2P client interface in a case where no
separate P2P group interface is used and when the disconnection is
triggered by something else than an explicit indication of GO
terminating the group.
Fix this by relaxing network block matching rules when figuring out
whether any of the configured network blocks could be in P2P use. The
p2p_group flag alone should be enough for this since temporary P2P group
network blocks are removed once the P2P group is terminated.
Signed-hostap: Jouni Malinen <j@w1.fi>
Channel 14 is available only in Japan and is DSSS-only according to
IEEE 802.11-2012 19.4.3 and MIC Equipment Ordinance (EO)
for Regulating Radio Equipment article 49.20.
At the same time, P2P should avoid using DSSS modulation in normal
operation according to P2P specification v1.2 2.4.1.
Signed-hostap: Mykyta Iziumtsev <mykyta.iziumtsev@gmail.com>
intended-for: hostap-1
Driver could reject the new scan based on any virtual interface
running a concurrent scan. As such, mark the pending scan callback
for P2P based on any interfaces instead of just the one used for
the p2p_scan operation.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since we have a global P2P module, the flag to trigger scan completion
events to it needs to be in similar context. The previous design
maintained this separately for each virtual interface and if P2P module
did not run its scan operation on the virtual interface that completed
the scan, P2P module would not be allowed to restart operations
properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 0d30cc240f forced
wpa_s->current_ssid and wpa_s->key_mgmt to be cleared in
wpa_supplicant_mark_disassoc() which gets called from
wpa_supplicant_event_disassoc(). This broke IEEE 802.1X authentication
failure processing and P2P deauthentication notification (group
termination).
Fix this by splitting wpa_supplicant_event_disassoc() into two parts and
make wpas_p2p_deauth_notif() indicate whether the interface was removed.
If so, the last part of disassocition event processing is skipped. Since
the wpa_supplicant_mark_disassoc() call is in the second part, the above
mentioned issues are resolved. In addition, this cleans up the P2P group
interface removal case by not trying to use fast reconnection mechanism
just before the interface gets removed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The wpa_s->current_ssid pointer may get cleared, e.g., when
disconnected. Commit 30ee769235 made
wpas_p2p_group_delete() exit early before removing a P2P interface in
this type of case. That can cause number of issues from p2p_group_remove
command failing to busy loop when terminating wpa_supplicant if there is
a P2P group interface in client mode and that interface happens to be in
disconnected state. Fix these issues by allowing wpas_p2p_group_delete()
remove the P2P group interface regardless of whether wpa_s->currnt_ssid
is set.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The freq and ht40 parameters can now be used with the p2p_invite
command when reinvoking a persistent group as the GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This commit does not yet address support for different device roles,
i.e., the same set of subelements are returned regardless of which
role was indicated in the request.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_cli p2p_serv_disc_req command can now be used to request WSD
request to be sent to specified or all peers who support WSD.
format: wifi-display <list of roles> <list of subelements>
examples:
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source] 2,3,4,5
p2p_serv_disc_req 02:01:02:03:04:05 wifi-display [pri-sink] 3
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [sec-source] 2
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source+sink] 2,3,4,5
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source][pri-sink] 2,3,4,5
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the P2P management operations are handled within the driver, the
P2P service entries were not freed when terminating wpa_supplicant.
Fix this by calling wpas_p2p_service_flush() even if the P2P module
within wpa_supplicant has not been initialized.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This limits the maximum size of the p2p_client_list parameter that
is maintained at the GO for a persistent group. In other words, only
the 100 most recently seen P2P clients are kept in the list.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
This list can get truncated due to too many addresses getting added.
Reorder the entries in a way that allows the most recently added values
to be maintained in the list and use better debug/error messages when
parsing the value.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
Previously, all station mode scan operations were either skipped or
delayed while any P2P operation was in progress. To make concurrent
operations easier to use, reduce this limitation by allowing a scan
operation to be completed in the middle of a p2p_find. In addition,
allow station mode association to be completed. When the station mode
operation is run to its completion (scan results not acted on,
connection to an AP completed, connection failed), resume the p2p_find
operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the p2p_find command is used without the delay parameter, a 500 ms
default search delay will now be used when any interface using the same
radio is in an concurrent operation. "p2p_find delay=0" can be used to
enforce the old behavior in such a case if needed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A new optional delay=<search delay in milliseconds> parameter can now be
used with p2p_find command to request an extra delay between search
iterations. This can be used, e.g., to make p2p_find friendlier to
concurrent operations by avoiding it from taking 100% of the radio
resources.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Increase GO config timeout if HT40 is used since it takes some time
to scan channels for coex purposes before the BSS can be started.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add optional "ht40" argument for p2p_group_add command to enable 40 MHz
in 5GHz band. This configures the secondary channel, when HT support is
enabled and if the HW supports 40 MHz channel width.
Signed-hostap: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
wpa_s->removal_reason was set only when calling wpas_p2p_group_delete()
and while couple of call places did not set this, it should really be
set in each case. As such, it works better as a function parameter than
a variable in struct wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
p2p_group_remove should only attempt to remove P2P group
interfaces and fail on non-P2P group interfaces.
Signed-hostap: Michael Naumov <michael.naumov@intel.com>
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
This enables setting a different max inactivity timeout for P2P GO.
This timeout is used to detect inactive clients. In some scenarios
it may be useful to have control over this and set a shorter timeout
than the default 300s. For example when running STA and P2P GO interfaces
concurrently, the STA interface may perform scans which may cause the
GO to miss a disassoc / deauth frames from a client and keep assuming
that the client is connected until the inactivity detection kicks in.
300 secs is a bit too long for such scenarios and creates a bad user
experience.
Signed-hostap: Eyal Shapira <eyal@wizery.com>
A p2p_find during provisioning shall not allow the enrollee to
pick the network, hence disable p2p_find during provisioning.
Signed-hostap: Sunil Dutt Undekari <duttus@codeaurora.org>
The wpas_p2p_pd_before_join_timeout could be left behind if the PD
Request in p2p_connect-auto case does not succeed. This timeout can
result in unexpected operations since it could trigger join operation
while going through GO Negotiation. Fix this by canceling the timeout
when falling back to GO Negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 361cdf3400 changed the way the
group formation timeout is used on P2P client. However, it resulted in
clearing the timeout on the GO when the GO started beaconing. This is
not correct since the timeout is supposed to be maintained until at
least the completion of the WPS provisioning step. Fix this regression
by clearing the timeout here only in the case we are not GO in group
formation phase.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The previous version set scan_res_handler unconditionally and then
cleared it if scan request failed. This can result in incorrect clearing
of the handler to NULL for a previously started scan that has not yet
completed. This can make p2p_find command fail to use the
start-after-scan-completion mechanism in some cases. Fix this by setting
scan_res_handler properly after having verified that the driver command
for starting the scan was successful.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
Perform addition additional scan runs on the operating channel of the GO
(if known from previous scan results) and fall back to initiate the PD
for GO Negotiation if these additional scans do not detect the peer as
GO.
Signed-hostap: Sunil Dutt Undekari <duttus@codeaurora.org>
Commit 361cdf3400 extended the use of
group formation timeout for the way handshake, but the registration was
done on the group_interface while the cancellation was done on the
parent interface. Fix the registration to set the eloop timeout on
parent to address potential issues when using a separate group
interface.
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
Commit aa9bb7644b improved robustness
of p2p_connect-auto mechanism by using older scan results to help in
determination whether the peer was operating a GO. Improve this by
accepting new GO information from scan-for-WPS-provisioning results
even if the GO is not yet ready for WPS.
In addition, fix an issue where Provision Discovery exchange timeout
could have left offchannel TX operation in progress when the fallback
was used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is a workaround for interoperability issues with some deployed P2P
implementations that require a Provision Discovery exchange to be used
before GO Negotiation. The new provdisc parameter for the p2p_connect
command can be used to request this behavior without having to run a
separate p2p_prov_disc command.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The P2P implementation assumes that the first wpa_s interface instance
is used to manage P2P operations and the P2P module maintains a pointer
to this interface in msg_ctx. This can result in issues (e.g., use of
freed memory) when the management interface is removed. Fix this by
deinitializing global P2P data if the interface that created it is
removed. This will disable P2P until the next interface is added.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
This can be used with P2P management operations that need to verify
whether the local device is operating a specific group based on
P2P Group ID attribute from a peer.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previusly the peer was assumed to not be operating a GO if the BSS entry
for it was not updated in the single scan run started by
p2p_connect-auto. This is not very robust since a scan may miss the peer
if either a Probe Request or Probe Response frame is lost. Improve
robustness by assuming the peer is still operating the GO and starting
the join operation. If the GO is not found during PD-for-join or the
single-channel scans during the join, fall back to GO Negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This workaround for Windows 7 WPS probing mechanism was previously
allowed only with hostapd, but the same interoperability issue can
happen with wpa_supplicant AP/GO mode. Allow the workaround to be
enabled in wpa_supplicant configuration for these uses.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to allow the max_sta_num parameter set in the main
configuration file to apply to dynamically created P2P group
interfaces.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
An existing persistent group information can now be used to force GO
Negotiation to use the previously used SSID/passphrase from a persistent
group if we become a GO. This can be used as an alternative to inviting
a new P2P peer to join the group (i.e., use GO Negotiation with GO
intent 15 instead of starting an autonomous GO and using invitation),
e.g., in case a GO Negotiation Request is received from a peer while we
are not running as a GO. The persistent group to use for parameters is
indicated with persistent=<network id> parameter to p2p_connect.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant can now be requested to automatically figure out whether
the indicated peer is operating as a GO and if so, use join-a-group
style PD instead of pre-GO Negotiation PD.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The p2p_dev_addr parameter in the P2P-PROV-DISC-FAILURE event (added in
commit f65a239ba4) was supposed to the P2P
Device Address of the peer, not the local device.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add provisional discovery failure ctrl_iface event
(P2P-PROV-DISC-FAILURE) to indicate to the application layer in case of
PD failure.
Signed-off-by: Deepthi Gowri <deepthi@codeaurora.org>
A special value p2p_group_idle=-1 can now be used to configure the P2P
group idle mechanism to terminate a P2P client group immediately on any
disconnection after the completion of the initial 4-way handshake.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of relying on the P2P group idle timeout before the group
connection has been fully established, re-start the group formation
timeout in the end of the WPS provisioning step and clear it at the
successful completion of the initial 4-way handshake. This allows the
P2P group idle timeout to be set to a small value without triggering it
during the initial scan and connection attempt.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_drv_scan() may fail for the initial p2p_connect join scan request,
e.g., if the driver happened to be scanning at the time the new
operation was initialized. Previously, a special scan result handler was
registered regardless of whether the new scan was started. This could
result in partial scan results (e.g., from p2p_find social scan) from
being used as full results for join (or now more importantly for
p2p_connect auto) purposes. Fix this by registering the new scan result
handler only if wpa_drv_scan() returns success.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_connect command can now be used with an optional "auto" parameter
to request wpa_supplicant to determine automatically whether to use
join-a-group operation (if the peer is operating as a GO) or group
formation. This makes it easier for external programs to handle
connection type selection by offloading this to wpa_supplicant. The
previously used p2p_connect join commands can be replaced with
p2p_connect auto to use this new mechanism.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The previous commit did not use the correct pointer in all operations
and was specific to station mode interfaces. Fix and extend it to work
with AP/GO interfaces, too.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the driver does not indicate support for multi-channel concurrency,
abort join-group operation if the end result would result in use of
multiple operating frequencies with the same radio.
Signed-hostap: Jouni Malinen <j@w1.fi>
When a supplicant is deinited and shutting, disconnect from P2P groups.
This fixes a memory leak on variable dbus_groupobj_path on exiting
supplicant.
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
When forming a P2P group using WSC PIN method, if the PIN is entered
incorrectly the P2P client supplicant instance will crash as a result
of cleanup happening on data that is still in use in a case where a
separate P2P group interface is used.
For example, here is the path for the first crash:
eap_wsc_process():
- creates struct wpabuf tmpbuf; on the stack
- sets data->in_buf = &tmpbuf;
- calls wps_process_msg()
- which calls wps_process_wsc_msg()
- which, in case WPS_M4: calls wps_fail_event()
- which calls wps->event_cb()
- wps->event_cb = wpa_supplicant_wps_event()
- wpa_supplicant_wps_event()
- wpa_supplicant_wps_event_fail()
- which calls wpas_clear_wps()
- which calls wpas_notify_network_removed()
- which calls wpas_p2p_network_removed()
- which calls wpas_p2p_group_formation_timeout()
- which calls wpas_group_formation_completed()
- which calls wpas_p2p_group_delete()
- which calls wpa_supplicant_remove_iface()
- which calls wpa_supplicant_deinit_iface()
- which calls wpa_supplicant_cleanup()
- which calls eapol_sm_deinit()
- ... which eventually uses the ptr data->in_buf to free tmpbuf, our
stack variable and then the supplicant crashes
If you fix this crash, you'll hit another. Fix it and then a segfault.
The way we're cleaning up and deleting data from under ourselves here
just isn't safe, so make the teardown portion of this async.
Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
intended-for: hostap-1
The GO can indicate that the P2P Group session is ending by sending a
Deauthentication frame with reason code 3 (Deauthenticated because
sending STA is leaving) based on P2P specification section 3.2.9. Use
this reason code to remove the P2P client group without waiting for the
group idle timeout.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
On P2P group removal, the GO is deinitialized correctly (and the vif
mode is set back to sta in case of nl80211), but the P2P client mode
wasn't deinitialized, and the nl80211 vif stays in P2P client mode.
Add a new deinit_p2p_cli op (similar to deinit_ap), which currently only
sets the interface back to station mode.
Signed-hostap: Eliad Peller <eliad@wizery.com>
intended-for: hostap-1
Some applications require knowing about probe requests to identify
devices. This can be the case in AP mode to see the devices before they
connect, or even in P2P mode when operating as a P2P device to identify
non-P2P peers (P2P peers are identified via PeerFound signals).
As there are typically a lot of probe requests, require that an
interested application subscribes to this signal so the bus isn't always
flooded with these notifications. The notifications in DBus are then
unicast only to that application.
A small test script is also included.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The signal strength is currently never used as the only driver reporting
it is nl80211 which uses IEEE80211_RADIOTAP_DB_ANTSIGNAL which is never
populated by the kernel. The kernel will (soon) populate
IEEE80211_RADIOTAP_DBM_ANTSIGNAL instead though, so use that.
Also, since it was never really populated, we can redefine the signal
field to be in dBm units only.
My next patch will also require knowing the signal strength of probe
requests throughout the code (where available), so add it to the
necessary APIs.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
p2p_pref_chan configuration parameter can now be used to set the
list of preferred channel for P2P GO Negotiation. This will be used
in the priority order if the peer does not support the channel we
are trying to use as the GO (configured operating channel or the
best 2.4 GHz/5 GHz channel) for the case where a forced channel is
not used.
p2p_pref_chan=<op class:channel>,...
For example:
p2p_pref_chan=81:1,81:2,81:3,81:4,81:5,81:6
This would configure 2.4 GHz channels 1-6 as the preferred ones with
channel 1 the most preferred option.
These configuration parameters can be set in wpa_supplicant.conf and
dynamically updated with "wpa_cli set <param> <value>".
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use the normal group formation timeout during the provisioning phase to
avoid terminating this process too early due to group idle timeout.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the p2p_group_add command does not specify the operating channel,
make sure the operating channel set in the configuration file meets
the P2P requirements in the same way as is done with the frequency
specified as the command parameter.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, this provisioning info was cleared using the P2P Interface
Address of the GO as the key. That did not always work in the case the
where we joined an already running group. This could result in the next
connection to that same GO skipping provision discovery. Fix this by
finding the peer entry based on its P2P Device Address instead of the
P2P Interface Address which may not always be set.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
If a GO Negotiation peer is found, wpas_p2p_stop_find() stops the
negotiation and p2p_cancel can return success.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Copy the SSID and frequency of the selected group into go_params in
join-a-running-group case so that the scan optimization can be used for
the provisioning step similarly to the case of group formation. This
uses a specific SSID and a single channel scan to avoid unnecessary
frames during the step.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use Device Password ID in WSC IE of Probe Request and Probe Response
frames to advertise immediate availability of WPS credentials per P2P
specification sections 3.1.2.1.1 (Listen State), 3.1.2.1.2 (Scan Phase),
and 3.1.2.1.3 (Find Phase).
For now, the Device Password ID is set only for the case where we are
active GO Negotiation with a specific peer. In practice, this means that
the Probe Response frames during pending GO Negotiation (whenever in
Listen state) indicate availability of the credential.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The wpas_p2p_group_idle_timeout was getting cancelled in the beginning
of wpas_p2p_group_delete(). However, in the case of P2P client role,
this function called wpa_supplicant_deauthenticate() next and that ended
up changing state to WPA_DISCONNECTED which resulted in
wpas_p2p_notif_disconnected() rescheduling the timeout. This left the
unexpected timeout behind after the group was removed. If another group
operation was started within P2P_MAX_CLIENT_IDLE (10) seconds, that
timeout could end up terminating the group while it was still being set
up.
Fix this by reordering wpas_p2p_group_delete() to cancel the group idle
timeout only after having called wpa_supplicant_deauthenticate(). The
group idle timeout is still rescheduled, but it gets removed immediately
afterwards when the actual group information is being cleared.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A list of disallowed frequencies for P2P channel list can now be
configured with P2P_SET disallow_freq. The frequencies (or frequency
pairs) are comma separated. For example:
wpa_cli p2p_set disallow_freq 2462,5000-6000
The allowed P2P channel list is constructed by removing explicitly
disallowed channels from the channel list received from the driver.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Remove the GPL notification text from files that were initially
contributed by Atheros Communications or Qualcomm Atheros.
Signed-hostap: Jouni Malinen <j@w1.fi>
When a GO is operating a persistent group and invites a peer that has
been a P2P client in that persistent group, the Invitation Type in the
Invitation Request frame can be set to 1 to indicate that this is a
reinvocation of a persistent group. Do this based on the maintained
list of P2P clients that have been provided the credentials to this
group.
Signed-hostap: Jouni Malinen <j@w1.fi>
Even though the Provision Discovery Response frame from PD-before-join
does not really provide any additional information, it can be better to
wait for it before starting the join operation. This adds a minimal
extra latency in the most common case and cleans up the sequence of
driver operations and debug log by avoiding potential processing of the
Provision Discovery Response while already running a scan for the actual
connection.
If transmission of Provision Discovery Request fails, join operation is
started without the additional wait. In addition, a new timeout is used
to start the join if Provision Discovery Response is lost for any
reason.
Signed-hostap: Jouni Malinen <j@w1.fi>
Provision Discovery is used as a notification to the GO in the case we
are about join a running group. In such case, there is not much point in
indicating the provision discovery response events to external programs
especially when the PIN-to-be-displayed was different from the one
returned for the p2p_connect command. Skip this confusing event
completely for join-a-running-group case.
Signed-hostap: Jouni Malinen <j@w1.fi>
This will be needed to be able to move ctrl_iface TERMINATING event to
the end of interface removal.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Even though we may not update P2P peer entry while connected to the
peer as a P2P client, we should not be expiring a P2P peer entry while
that peer is the GO in a group where we are connected as a P2P client.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When a P2P group is removed, we better not leave possibly started
sched_scan running. This could happen when a separate group interface
was not used.
In addition, it looks safer to explicitly stop sched_scan before
starting P2P Listen or Find operations to make sure the offloaded
scanning is not running when doing similar P2P operations.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
