Commit graph

16 commits

Author SHA1 Message Date
Witold Sowa
8fc2fb56e4 wpa_supplicant: new DBus API implementation
This patch implements the new DBus API. Both, the new and the
previous API may work concurrently and may be turned on or off
separately in .config file.
Some features of the new API are:
 - more wpa_supplicant's events are signaled with DBus signals,
 - introspection data (requires libxml2 and may be disabled),
 - CurrentBSS and CurrentNetwork properties,
 - PropertyChanged signal for most of properties,
 - Relatively easy to extend.
.config options for the new API are: CONFIG_CTRL_IFACE_DBUS_NEW=y and
CONFIG_CTRL_IFACE_DBUS_INTRO=y for introspection.

This commit misses couple of parts from the full implementation
(these are still under review):
- fetching all configuration parameters for learning WPS information
- scan result BSS add/remove notification (register_bss() and
  unregister_bss() notification callbacks)
2009-11-09 23:51:59 +02:00
Witold Sowa
86b89452f6 Use shared functions for network operations and param changes
Instead of implementing these separately in various control
interface handlers, use shared functions. These add some of the
previously missing notification calls, too, for the affected areas.
2009-09-13 21:16:43 +03:00
Jouni Malinen
8bac466b00 Add wpa_supplicant notification calls
This introduces a new mechanism for collecting notification calls into
a single place (notify.c). As a result of this, most of the
wpa_supplicant code does not need to know about dbus (etc. mechanisms
that could use the notifications). Some empty placeholder functions are
also added in preparation of new dbus code that needs more event
notifications.
2009-09-13 20:53:32 +03:00
Jouni Malinen
52eb293dd2 WPS: Add support for AP reconfiguration with wps_reg
wpa_supplicant can now reconfigure the AP by acting as an External
Registrar with the wps_reg command. Previously, this was only used
to fetch the current AP settings, but now the wps_reg command has
optional arguments which can be used to provide the new AP
configuration. When the new parameters are set, the WPS protocol run
is allowed to continue through M8 to reconfigure the AP instead of
stopping at M7.
2009-09-06 13:58:15 +03:00
Dan Williams
cb8564b1dd dbus: add 'scanning' property
When the supplicant is connected and performs a scan, it doesn't enter
WPA_SCANNING state for various reasons.  However, external programs
still need to know that the supplicant is scanning since they may not
wish to perform certain operations during a scan (as those operations
will likely fail or yield incorrect results).  Add a 'scanning' property
and signal to the supplicant dbus interface to allow clients to
synchronize better with the supplicant when it scans.

Signed-off-by: Dan Williams <dcbw@redhat.com>
2009-05-27 21:06:40 +03:00
Jaime Soriano Pastor
e8fa6039f6 WPS methods exported over DBus
I've exported the methods wpsPbc, wpsReg and wpsPin (patch attached),
so wpa_supplicant should be able to connect with WPS using the dbus
interface. I couldn't test it well because the problem seems to be in
my wireless card, a Broadcom BCM4328. At least it seems to do the same
using both interfaces. With ndiswrapper driver the "wpsie" entry
(thanks Dan!) didn't appear, and with the Broadcom wl driver it
appears but I cannot associate using WPS.
2009-05-06 13:23:41 +03:00
Helmut Schaa
01a569e8a1 wpa_supplicant: add DBus method for changing debug parameters
Add a new DBus method "setDebugParams" which takes the parameters
debug_level, debug_timestamp and show_keys as input and updates the
internal debug variables accordingly.

To change the debug level, enable/disable timestamps and enable/disable
show_keys the following dbus-send command can be used:

dbus-send --system --dest=fi.epitest.hostap.WPASupplicant --print-reply
/fi/epitest/hostap/WPASupplicant fi.epitest.hostap.WPASupplicant.setDebugParams
int32:0 boolean:false boolean:false

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
2009-05-06 11:54:00 +03:00
Jouni Malinen
2d5b792d2b Add preliminary hostapd data structure initialization for AP mode
wpa_supplicant can now initialize hostapd data structures when mode=2 is
used to set up an AP. The hostapd configuration is not yet set based on
wpa_supplicant network configuration block. In addition, the glue code
for hostapd driver_ops needs number of functions that will be needed for
AP functionality.
2009-03-26 20:37:05 +02:00
Jouni Malinen
7c2849d2a0 Add BSS flags to scan results to indicate signal quality validity
These flags are used to mark which values (level, noise, qual) are
invalid (not available from the driver) and whether level is using dBm.
D-Bus interface will now only report the values that were available.
2009-02-18 13:40:38 +02:00
Jouni Malinen
dcc03dbe78 Use NULL, not 0, when comparing a pointer 2009-01-03 21:01:20 +02:00
Jouni Malinen
a17df5fb8b Fixed number of doxygen warnings 2009-01-02 22:28:04 +02:00
Jouni Malinen
ad08c3633c Added preliminary Wi-Fi Protected Setup (WPS) implementation
This adds WPS support for both hostapd and wpa_supplicant. Both programs
can be configured to act as WPS Enrollee and Registrar. Both PBC and PIN
methods are supported.

Currently, hostapd has more complete configuration option for WPS
parameters and wpa_supplicant configuration style will likely change in
the future. External Registrars are not yet supported in hostapd or
wpa_supplicant. While wpa_supplicant has initial support for acting as
an Registrar to configure an AP, this is still using number of hardcoded
parameters which will need to be made configurable for proper operation.
2008-11-23 19:34:26 +02:00
Dan Williams
93ef879f0f wext: fix maxrate calculation
When scan results got moved from wpa_scan_result -> wpa_scan_res, the
'maxrate' member was dropped from wpa_scan_res.  The D-Bus interface
used 'maxrate', which was replaced with wpa_scan_get_max_rate().
Unfortunately, wpa_scan_get_max_rate() returns 802.11 rate values
directly from the IE, where 'maxrate' was the rate in bits/second.  The
supplicant internally fakes an IE for wpa_scan_res from the value of
wpa_scan_result->maxrate, but interprets ->maxrate as an 802.11 rate
index.

As a side-effect, this fixes a soft-break of the D-Bus control API since
the wpa_scan_res change was introduced.
2008-07-15 20:07:50 +03:00
Jouni Malinen
b5aebee49e Fixed dbus build without OpenSSL. 2008-06-02 18:45:45 +03:00
David Smith
e403be0b12 Add setSmartcardModules DBus message to set pkcs11 and opensc options
This will be used by most importantly network manager to set smartcard
options at run time.
2008-04-28 17:15:56 +03:00
Jouni Malinen
6fc6879bd5 Re-initialize hostapd/wpa_supplicant git repository based on 0.6.3 release 2008-02-27 17:34:43 -08:00