This code sequence was already used at two different places (and an
additional one has been proposed), so add a common helper function to
avoid having to copy-paste this functionality in multiple locations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
For testing purposes, it is useful to have an option to be able to
reject BTM Request sent by AP in order to verify the AP behavior upon
BTM Request rejection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a testing mechanism to allow association disallowed set by AP to be
ignored. This can be used to verify AP behavior for disallowing a
specific association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Implement "SET ignore_auth_resp <0/1>" command to simulate auth/assoc
response loss and EAPOL RX packet loss by ignoring corresponding
incoming events.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
All the 3 control interfaces: socket based, dbus & binder needs to
perform the same sequence of steps for network add/remove. So, move
these to a common utility method in |wpa_supplicant.c| instead of
duplicating the code everywhere.
Signed-off-by: Roshan Pius <rpius@google.com>
Move out the disconnect command handling from |ctrl_iface.c| to
|wpa_supplicant.c| so that it can be reused across the different
control interfaces (socket, dbus & binder).
Signed-off-by: Roshan Pius <rpius@google.com>
This is needed for hwsim test cases to allow multiple STA-initiated SA
Query operations in short amount of time.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is mainly for testing purposes to allow multiple FETCH_OSU ANQP
operations to be ran without having to wait for full scan between each
query.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows P2P Listen to be offloaded to device to enhance power
saving.
To start P2P listen offload, from wpa_cli interface, issue the command:
p2p_lo_start <freq> <period> <interval> <count>
To stop P2P listen offload, issue the command:
p2p_lo_stop
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In some cases parsing of the mesh scan info for a BSS or the P2P scan
info can fail. One reason can be that the Beacon/Probe Response frame
contained malformed length vendor IEs which are not parsed when adding
to the BSS table. Instead of skipping the whole BSS of the BSS command,
just skip the part that failed to parse.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
This allows using P2PS config method with or without PIN for connection.
wpa_supplicant should internally handle the default PIN "12345670" and
shall also allow connection irrespective of PIN used in P2P_CONNECT.
For example,
1. P2P_CONNECT 02:2a:fb:22:22:33 p2ps
2. P2P_CONNECT 02:2a:fb:22:22:33 xxxxxxxx p2ps
Where the second one is maintained for backwards compatibility.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
work->type was pointing to the allocated work->ctx buffer and the debug
print in radio_work_free() ended up using freed memory if a started
external radio work was removed as part of FLUSH command operations. Fix
this by updating work->type to point to a constant string in case the
dynamic version gets freed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to write hwsim test cases to verify management
frame processing sequences with dropped or modified frames. When
ext_mgmt_frame_handling is used, this new command can be used to request
wpa_supplicant to process a received a management frame, e.g., based on
information reported in the MGMT-RX events.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows local GO to fetch the P2P Interface Address of a P2P Client
in the group based on the P2P Device Address for the client. This
command should be sent only on a group interface (the same peer may be
in multiple concurrent groups).
Usage:
P2P_GROUP_MEMBER <P2P Device Address>
Output:
<P2P Interface Address>
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
Parse a received neighbor report and report for each neighbor report the
data received for it:
RRM-NEIGHBOR-REP-RECEIVED bssid=<BSSID> info=0x<hex> op_class=<class> chan=<chan> [lci=hex] [civic=hex]
Note that this modifies the previous format that originally reported
only the length of the received frame.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Handle radio measurement request that contains LCI request. Send
measurement report based on a configurable LCI report element. The LCI
report element is configured over the control interface with
SET lci <hexdump of the element>
and cleared with
SET lci ""
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add an option to request LCI and Location Civic Measurement in Neighbor
Report Request frame, as described in IEEE P802.11-REVmc/D5.0, 9.6.7.6.
Note: This changes the encoding format of the NEIGHBOR_REP_REQUEST
ssid=<val> parameter. This used to be parsed as raw SSID data which is
problematic for accepting additional parameters. The new encoding allows
either a string within double-quotation marks or a hexdump of the raw
SSID.
Thew new format:
NEIGHBOR_REP_REQUEST [ssid=<SSID>] [lci] [civic]
Signed-off-by: David Spinadel <david.spinadel@intel.com>
This avoids unnecessary flushing of the PMKSA cache entry and EAP
session data when processing SET_NETWORK commands that set a network
profile parameter to the same value that the parameter already has.
Introduce a new wpa_config_set() and wpa_config_set_quoted() return
value (==1) signifying that the new value being set for the
corresponding field equals to the already configured one so that the
caller can determine that nothing changed in the profile.
For now, this does not cover all the network profile parameters, but
number of the most commonly used parameters are included to cover the
Android use cases where the framework may have issued SET_NETWORK
commands that would have unnecessarily prevented use of PMKSA caching or
EAP fast reauthentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This patch add functionality of mesh SAE PMKSA caching. If the local STA
already has peer's PMKSA entry in the cache, skip SAE authentication and
start AMPE with the cached value.
If the peer does not support PMKSA caching or does not have the local
STA's PMKSA entry in the cache, AMPE will fail and the PMKSA cache entry
of the peer will be removed. Then STA retries with ordinary SAE
authentication.
If the peer does not support PMKSA caching and the local STA uses
no_auto_peer=1, the local STA can not retry SAE authentication because
NEW_PEER_CANDIDATE event cannot start SAE authentication when
no_auto_peer=1. So this patch extends MESH_PEER_ADD command to use
duration(sec). Throughout the duration, the local STA can start SAE
authentication triggered by NEW_PEER_CANDIDATE even though
no_auto_peer=1.
This commit requires commit 70c93963ed
('SAE: Fix PMKID calculation for PMKSA cache'). Without that commit,
chosen PMK comparison will fail.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends the wpa_supplicant PMKSA_FLUSH control interface command to
allow the PMKSA list from the authenticator side to be flushed for AP
and mesh mode. In addition, this adds a hostapd PMKSA_FLUSH control
interface command to flush the PMKSA entries.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends the wpa_supplicant PMKSA control interface command to allow
the PMKSA list from the authenticator side to be listed for AP and mesh
mode. In addition, this adds a hostapd PMKSA control interface command
to show the same list for the AP case.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This allows a mesh peer connection to be initiated manually in
no_auto_peer mesh networks.
Signed-off-by: Natsuki Itaya <Natsuki.Itaya@jp.sony.com>
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This command allows the specified mesh peer to be disconnected.
Signed-off-by: Natsuki Itaya <Natsuki.Itaya@jp.sony.com>
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The bssid and priority parameters in a network block do not have any
effect on the validity of an EAP session entry, so avoid flushing the
cached session when only these parameters are changed. This is mainly to
allow forced roaming or network selection changes without causing fast
reauthentication to be disabled if the changes are done during RSN
association that used EAP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The existing implementation in p2p_ctrl_set used a hard-coded operating
class 81 which is only suitable for the social channels in the 2.4 GHz
band, and will not work for the social channel in the 60 GHz band.
Extend this by adding an optional op_class argument to P2P_SET
listen_channel. If not specified, use the default value of 81 to match
existing behavior.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
"INTERFACES ctrl" can now be used to fetch a list of network interfaces
and their control interfaces, e.g., to fetch the UDP port information
for the control interface.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Add an option to configure a candidate list to BSS transition query
("list" as the second argument to WNM_BSS_QUERY). The candidate list is
built from the available scan results. If no updated scan results (< 10
sec) are available, the command fails.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Remove the fallback dependency on os_random() when generating a WPS pin.
This is exceptionally unlikely to ever be called as the call to
os_get_random() is unlikely to fail. The intention is to facilitate
future removal of os_random() as it uses a low quality PRNG.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Ensure that characters are represented as unsigned char when using
isblank() and isspace(). These function take in a "int c" argument, but
it needs to be unsigned for the cases where EOF is not indicated.
Signed-off-by: Roy Marples <roy@marples.name>
This is needed to get proper P2P group removal processing for some test
cases. discovery_group_client followed by nfc_p2p_client was able to hit
a case where the P2P group idle timeout survived to the next group
instance because of the FLUSH command not clearing the group and this
timeout properly.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the FLUSH command to trigger auto connect mechanism
to schedule a new scan in 100 ms. This is not desired since all the
network profiles will be removed immediately and the scan or an attempt
to reconnect would not be of any benefit here. Such a scan in 100 ms can
cause issues for cases where multiple test sequences are run back to
back, so prevent this by clearing wpa_supplicant state to DISCONNECTED
(which avoids scheduling of the 100 ms scan trigger on disconnection) if
the state was AUTHENTICATING or higher when the FLUSH command was
issued.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wps_force_{auth,encr}_types parameters can be used in test build
(CONFIG_WPS_TESTING) to force wpa_supplicant to use the specified value
in the Authentication/Encryption Type flags attribute. This can be used
to test AP behavior on various error cases for which there are
workarounds to cover deployed device behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new optional ssid=<hexdump> argument to P2P_CONNECT can be used to
make P2P Client operations during join-an-existing-group more robust by
filtering out scan results based on the SSID in addition to the P2P
Device/Interface Address. This can help if the same MAC address has been
used in multiple groups recently and the cached scan results may still
include an older BSS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
At least one of the wpas_p2p_connect() callers (NFC join case) already
had access to the Group SSID. Pass that information through
wpas_p2p_connect() to wpas_p2p_join() so that the join operation can
filter out incorrect groups more easily.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a new command based Hotspot 2.0 icon retrieval option.
In short, here is the new command sequence:
1. REQ_HS20_ICON <bssid> <file-name>
2. event: RX-HS20-ICON <bssid> <file-name> <size>
3. GET_HS20_ICON <bssid> <file-name> <offset> <size>
(if needed, repeat with larger offset values until full icon is
fetched)
5. DEL_HS20_ICON <bssid> <file-name>
REQ_HS20_ICON is a new command that is analogous to HS20_ICON_REQUEST
with the slight difference that an entry to store the icon in memory is
prepared. The RX-HS20-ICON event has been augmented with BSSID,
file-name and size, and GET_HS20_ICON is used to retrieve a chunk of up
to <size> bytes of icon data at offset <offset>. Each chunk is returned
as a base64 encoded fragment, preceded by "HS20-ICON-DATA", BSSID, and
file-name as well as the starting offset of the data.
If there is no entry prepared for the icon when the ANQP result comes
back, hs20_process_icon_binary_file falls back to legacy behavior.
Finally the DEL_HS20_ICON command deletes (all) icons associated with
BSSID and file-name (there could be several if retries are used and they
have different dialog tokens).
Signed-off-by: Jan Nordqvist <jannq@google.com>
SIGNAL_MONITOR THRESHOLD=DD HYSTERESIS=DD command will request signal
strength monitoring events based on there having been requested amount
of drop in the signal strength. The threshold value is the RSSI
threshold in dBm for the event to be sent. 0 threshold can be used to
disable monitoring. The hysteresis value is RSSI hysteresis in dB to
specify the minimum amount of change before a consecutive event is
reported.
With nl80211 driver interface, these values map to the
NL80211_CMD_SET_CQM command with NL80211_ATTR_CQM_RSSI_THOLD and
NL80211_ATTR_CQM_RSSI_HYST attributes to the driver.
This command cannot be used when bgscan module is in use since that
depends on being able to control the connection monitoring parameters.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
The new wpa_supplicant control interface command "TEST_ASSOC_IE
<hexdump>" can now be used to override the WPA/RSN IE for Association
Request frame and following 4-way handshake to allow protocol testing of
AP side processing of WPA/RSN IE.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new methods are
1. VendorElemAdd "i" "ay" i=integer ay=array of bytes
2. VendorElemGet "i" i=integer (output array of bytes)
3. VendorElemRem "i" "ay" i=integer ay=array of bytes
These provide functionality similar to the control interface commands
VENDOR_ELEM_ADD, VENDOR_ELEM_GET, and VENDOR_ELEM_REMOVE.
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
Signed-off-by: Kyeong-Chae Lim <kcya.lim@samsung.com>
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Signed-off-by: Dilshad Ahmad <dilshad.a@samsung.com>
[VendorElemGet to return array of bytes instead of string; cleanup]
Signed-off-by: Jouni Malinen <j@w1.fi>
This may speed up some hwsim test case sequencies by avoiding a wait for
a scan at the end of a test case to complete.
Signed-off-by: Jouni Malinen <j@w1.fi>
