When p2p_invite persistent=<id> is used to request a persistent group to
be re-invoked, the peer may reply with status=1 (info not yet available)
if upper layer processing of the invitiation is requested. The peer is
ten expected to start another invitation exchanged within 120 seconds if
the user authorizes the connection. Allow this process to be used more
easily by automatically authorizing the peer that we tried to invite to
use this second invitation sequence even if persistent_reconnect=0.
For this mechanism to work, the device that starts the invitation needs
to start listen mode to be able to receive the invitation request from
the peer. At least for now, this is not done automatically, but future
changes could potentially enable this automatically at least if there
are no concurrent operations in progress.
Example sequence on the initiator:
cmd: P2P_INVITE persistent=1 peer=<addr>
event: P2P-INVITATION-RESULT status=1
cmd: P2P_LISTEN 120
wait for peer to start another invitiation round.. group will be
re-invoked automatically
On the peer (with persistent_reconnect=0):
event: P2P-INVITATION-RECEIVED sa=<addr> persistent=1 [freq=<MHz>]
wait for user approval
cmd: P2P_INVITE persistent=1 peer=<addr>
group will be re-invoked automatically
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When a device that is a GO in a persistent group receives an Invitation
Request from a P2P client and persistent_reconnect=0, upper layer is
notified of this with P2P-INVITATION-RECEIVED event. The upper layer is
supposed to run another invitation exchange is this case, but if that
does not happen and the GO is started without successful (status=0)
invitation exchange, the operating channel for the group may end up
getting set in a way that the P2P client is not able to support. Provide
optional freq parameter in the P2P-INVITATION-RECEIVED event on the GO
side. If this parameter is received and the upper layer decides to issue
P2P_GROUP_ADD command, that command should include this freq parameter
to make sure the operating channel gets selected from the set that the
peer can support.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
beacon_int (in TU) can now be used to configure Beacon interval for AP
mode operations (including P2P GO) in wpa_supplicant. This can be set
either in a network block or as a global parameter in the configuration
file (or with "SET beacon_int <value>" control interface command) to
apply for all networks that do not include the beacon_int parameter to
override the default.
In addition, this commits extends the dtim_period parameter to be
available as a global parameter to set the default value. dtim_period is
now stored in the configuration file, too, if it was set.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Peer device includes its list of allowed operating channels in the
Invitation Response frame. When we are becoming the GO, use that list
from the peer to filter out acceptable channels to avoid selecting a
channel that the peer is unable to use.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When re-invoking a persistent group in P2P client role, the new
pref=<MHz> parameter can now be used with the p2p_invite command to
indicate a preferred operating frequency. Unlike the older freq=<MHz>
parameter, this leaves GO an option to select another channel (from our
supported channels) if the GO cannot accept the channel.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_connect() and p2p_invite() cases used more or less identical
implementatin. Use a shared function to avoid duplicated code.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If multi channel concurrency is supported, we have to populate the
p2p_channels with list of channels that we support. Use the same design
that was previously added for GO Negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The VHT IE struct just has an opaque 8-byte array for the MCS
set, make it more expressive by explicitly naming the pieces.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Commit fb8984fd6f cleared wps_method to
WPS_NOT_READY in p2p_stop_find_for_freq() as an attempt to clear
authorization when a group formation is cancelled. However, this code
path is hit also in cases where the user did not actually cancel
anything (e.g., from p2p_process_go_neg_req()). As such, it is not fine
to clear wps_method here even if it could be proper for some cases. For
now, revert that part to avoid regressions and consider clearing
wps_method on cancel separately.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
In case we have replied to a peer's GO Negotiation Request frame with a
GO Negotiation Response frame using status code
info-currently-unavailable (1), the peer is likely going to wait for us
to initiate GO Negotiation on its Listen channel. We were previously
using alternativing send-GO-Neg-Req and Listen phase when providing that
response after the user had authorized the connection. However, the
Listen phase here is unnecessary in this case and will make the
connection take longer time to go through. Skip the Listen phase and
make the wait-for-GO-Neg-Resp timeout random between 100 and 200 ms to
avoid getting in sync with the peer. In practice, this will make us
retry GO Negotiation Request frames more frequently and remain on the
peer's Listen channel for most of the time when initiating GO
Negotiation after status=1 response.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There may be environments in which large number of devices are operating
on the social channels. In such cases, it is possible for the Action
frame TX operation wait for quite long time before being able to get the
frame out. To avoid triggering GO Negotiation failures, increase the
timeouts for GO Neg Req (with TX ACK) and GO Neg Resp (with or without
TX ACK as long as status=0) to 500 ms.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Most of the print_bss_info() cases were already returning zero lenth to
avoid returning partial returns to the BSS commands, but the HS 2.0 and
Wi-Fi Display entries behaved differently. Make those consistent with
rest of the items.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows ctrl_iface users to iterate through the BSS entries by
fetching multiple BSS entries with "BSS RANGE=N-" without having to use
one extra round to get empty return value as the indication of the last
entry having been found.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This flag will add ==== delimiter between to separate bss results.
Unlike the other BSS command MASK values, this delimiter is not
included by default to avoid issues with existing users of the BSS
command.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This patch uses existing scan results for fast connection on REASSOCIATE
and RECONNECT commands.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
wpa_supplicant uses 4096 byte buffer for control interface responses, so
wpa_cli should do the same to avoid truncating responses unnecessarily.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for the driver to indicate multiple Probe Request frames
that would be processed in a single loop. If those frames happen to be
from a peer which with we are trying to start GO Negotiation, multiple
timeouts to start GO Negotiation (p2p_go_neg_start) could end up being
scheduled. This would result in confusing burst of multiple GO
Negotiation Request frames being sent once the RX loop finally
concludes. Avoid this by scheduling only a single eloop timeout to
trigger GO Negotiation regardless of how many Probe Request frames from
the peer is received. In addition, make sure this timeout gets canceled
in p2p_deinit().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If we have already sent out GO Negotiation Response and are waiting for
the peer to reply with GO Negotiation Confirm, there is no point in
re-starting GO Negotiation based on Probe Request frame from the peer.
Doing that would just result in confusing GO Negotiation exchange with
multiple sessions running at the same time.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The device that is selected as the GO shall incode P2P Group ID
attribute in GO Negotiation Response/Confirm message. Previously we did
not reject a message without that attribute since it was possible to
continue operations even without knowing the SSID. However, this can
potentially result in confusing results since missing P2P Group ID
attribute can be a sign of conflicting GO role determination (both
devices assuming the peer is the GO). To get clearer end result for the
GO Negotiation, reject this as a fatal error. In addition, stop GO
Negotiation if GO Negotiation Confirm indicates non-zero status since
that is also a fatal error.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 624b4d5a64 changed GO Negotiation
to use the same Dialog Token value for all retransmissions of the GO
Negotiation Request within the same session. However, it did leave the
tie breaker bit changing for each frame. While this should not have
caused issues for most cases, it looks like there are possible sequences
where the peer may end up replying to two GO Negotiation Request frames
with different tie breaker values. If in such a case the different GO
Negotiation Response frames are used at each device, GO role
determination may result in conflicting results when same GO intent is
used.
Fix this by assigning the tie breaker value at the same time with the
dialog token (i.e., when processing the p2p_connect command instead of
for each transmitted GO Negotiation Request frame) to avoid issues with
GO selection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's VHT capability is required for the
driver to establish a TDLS link in VHT mode with a compatible peer.
Pass this information to the driver when the peer station is
getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to avoid errors when reporting the result of an NFC
connection handover that failed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
WSC specification 2.0 section 7.4 describes OOB password to be expressed
in ASCII format (upper case hexdump) instead of raw binary.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant can now generate the WPS carrier record for connection
handover response when acting as an ER. The AP whose configuration is
provided in this way is identified with an UUID as an argument to
wps-nfc.py.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the credential to use for a connection with a specific BSS
was picked arbitrary based on first found match of each matching
mechanism. While the credential priorities were used elsewhere, this did
not take into account that different mechanisms could find multiple
matching credentials. As such, the highest priority credential was not
always used in case more than one credential matched with the selected
BSS. Fix this by checking credential priorities again during connection
request.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 2d9ffe1e85 broke GAS server
callback for receiving Public Action frames. The incorrect context
pointer was used in the public_action_cb2 case. Fix this to use the
correct context pointer.
Signed-hostap: Jouni Malinen <j@w1.fi>
Hostapd provides QoS info of the STA (Service Period & AC mask) to the
kernel during wpa_driver_nl80211_sta_add call. Bit 5 and Bit 6 of QoS
info represents the Max SP length. Fix an issue in the code to fetch the
Max SP by shifting right the QoS info by value WMM_QOSINFO_STA_SP_SHIFT.
(operator ">" is replaced with ">>" operator).
Signed-off-by: Srinivasan <srinivasanb@posedge.com>
Commit bbf41865c9 added calls to functions
that are only defined if CONFIG_WPS_NFC=y. Protect those calls properly
to avoid build issues.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When wpa_supplicant is controlling an AP mode interface, it can generate
the alternative carrier record for NFC connection handover select
message similarly to the way this is done in hostapd.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The last couple of changes to the control interface commands for NFC
connection handover had not yet been documented.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When wpa_supplicant is controlling an AP mode interface, it can generate
the NFC configuration token similarly to the way this is done in
hostapd.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds write-password option for the nfcpy example script for
wpa_supplicant to match hostapd wps-ap-nfc.py functionality.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"WPS_NFC_TOKEN <WPS/NDEF>" used to generate a new NFC password token
regardless of whether there was a pre-configured token in the
configuration. Change this to use the pre-configured value, if
available, instead. This allows the same command to be used to write the
password token to an NFC tag more conveniently.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The contents of the peer's capability and extended capability
information is required for the driver to perform TDLS P-UAPSD and Off
Channel operations. Pass this information to the driver when the peer
station is getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's HT capability and the QOS information is
required for the driver to perform TDLS operations. Pass this
information to the driver when the peer station is getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit a9a1d0f08a added vht_capabilities
to struct hostapd_sta_add_params but forgot to update
wpa_supplicant_tdls_peer_addset() to initialize the variable to NULL.
This could result in uninitialized pointer being used in
driver_nl80211.c when adding a TDLS peer entry. Fix this by clearing the
hostapd_sta_add_params with memset.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Registrar is allowed to propose another Device Password ID in M2. Make
Enrollee validate Device Password ID in M2 to check if this happened.
This commit adds support for changing from NFC password token to default
PIN for the case where the AP is the Enrollee and has both the NFC
password token and AP PIN enabled at the same time.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit ffdaa05a6b added support for using
NFC password token from an AP. However, it had a bug that prevented the
wpa_supplicant wps_reg command from being used with "nfc-pw" as the PIN
value. Fix string comparison to handle this correctly.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A TDLS Teardown frame with Reason Code 3 (Deauthenticated because
sending STA is leaving (or has left) IBSS or ESS) shall be transmitted
to all TDLS peer STAs (via the AP or via the direct path) prior to
transmitting a Disassociation frame or a Deauthentication frame to the
AP.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
