Commit graph

271 commits

Author SHA1 Message Date
Jouni Malinen
c267753ba2 Add support for using random local MAC address
This adds experimental support for wpa_supplicant to assign random local
MAC addresses for both pre-association cases (scan, GAS/ANQP) and for
connections. MAC address policy for each part can be controlled
separately and the connection part can be set per network block.

This requires support from the driver to allow local MAC address to be
changed if random address policy is enabled. It should also be noted
that number of drivers would not support concurrent operations (e.g.,
P2P and station association) with random addresses in use for one or
both.

This functionality can be controlled with the global configuration
parameters mac_addr and preassoc_mac_addr which set the default MAC
address policies for connections and pre-association operations (scan
and GAS/ANQP while not connected). The global rand_addr_lifetime
parameter can be used to set the lifetime of a random MAC address in
seconds (default: 60 seconds). This is used to avoid unnecessarily
frequent MAC address changes since those are likely to result in driver
clearing most of its state. It should be noted that the random MAC
address does not expire during an ESS connection, i.e., this lifetime is
only for the case where the device is disconnected.

The mac_addr parameter can also be set in the network blocks to define
different behavior per network. For example, the global mac_addr=1 and
preassoc_mac_addr=1 settings and mac_addr=0 in a home network profile
would result in behavior where all scanning is performed using a random
MAC address while connections to new networks (e.g.,
Interworking/Hotspot 2.0) would use random address and connections to
the home network would use the permanent MAC address.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-27 20:07:19 +03:00
Bojan Prtvar
1cc0d6a0eb wpa_supplicant: Use freq_list scan filtar in sched_scan
Global freq_list scan filtar was taken into account only by
req_scan and not by req_sched_scan. We want to allow the user
to limit the channels that wpa_supplicant will scan in req_sched_scan
requests as well.

Signed-off-by: Bojan Prtvar <bojan.prtvar@rt-rk.com>
2014-08-12 16:44:04 +03:00
Dmitry Shmidt
4ed3492206 PNO: Send Probe Request frames only for hidden SSIDs
Previously, offloaded scanning (PNO) on Android was including SSIDs from
all enabled networks regardless of the scan_ssid parameter which
resulted in different behavior for the offloaded case when comparing to
wpa_supplicant initiated scans.

Use the sched_scan match filter to allow broadcast SSID to be used for
scan_ssid=1 networks also with PNO to avoid running active scans for
SSIDs that have not been explicitly marked as requiring an SSID-specific
scan. This reduces exposure of configured network names on the device
when running offloaded scans while the host device is in sleep.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-07-03 16:44:43 +03:00
Li Jianyun
6891f0e6f4 Allow SCAN command to specify scan_ssid=1 SSIDs
The new "scan_id=<comma separated list of network ids>" parameter can
now be used to specify a list of network ids that have scan_ssid=1 to
indicate active scanning of the SSID. This adds the listed SSIDs to the
scan command to allow manual scan requests to perform active scans for
hidden SSIDs. For example, "SCAN scan_id=1,7,11" would run a scan with
the SSID fetched from the configured network blocks 1, 7, and 11
(assuming those are set with scan_ssid=1). The SSIDs will be included
even from network blocks that are currently disabled.

The maximum number of SSIDs added to the request is limited by the
driver support. If more than supported values are specified, the command
will fail (returns "FAIL").

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-07-02 12:52:08 +03:00
Johannes Berg
57a8f8af38 nl80211: Use low-priority scan for OBSS scan
Some drivers may support low-priority scans, if they do then
use that for OBSS scanning.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-06-22 00:47:06 +03:00
Jouni Malinen
bd10d93891 P2P: Clean up by moving ifdef CONFIG_P2P to p2p_suppplicant.h
This removes number of unnecessary #ifdef CONFIG_P2P blocks from generic
code by hiding the conditional build into p2p_supplicant.h with empty
inline functions.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-15 19:31:53 +03:00
Rashmi Ramanna
28fa4eb2b2 P2P: Fix scan optimization for GO during persistent group invocation
Commit 41d5ce9e0b was intended to scan for
GO on the negotiated channel for few iterations, but it did not work
correctly due to incorrect operator being used. Fix this by requiring
both conditions to be met for the single channel scan.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-05-13 15:49:06 +03:00
Sunil Dutt
8235f89f3f P2P: Mark the scan in p2p_in_invitation as p2p_probe
Mark the scan performed by the P2P Client in search of the GO
during the persistant reinvocation as a p2p_probe to avoid
unnecessary use of 802.11b rates.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-10 19:54:36 +03:00
Rashmi Ramanna
41d5ce9e0b P2P: Optimize scan for GO during persistent group invocation
Scan for GO on the negotiated operating channel for few iterations
before searching on all the supported channels during persistent group
reinvocation. In addition, use the already known SSID of the group in
the scans. These optimizations reduce group formation time.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-25 15:38:33 +02:00
Dmitry Shmidt
d3c9c35f32 Add freq= parameter to 'set pno' command
This allows channels-to-be-scanned to be specified for PNO similarly to
the scan command.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-03-21 23:56:46 +02:00
Peter Qiu
0f44ec8eba Add a reattach command for fast reassociate-back-to-same-BSS
Add "reattach" command to perform single-channel single-ssid scan
instead of full scan when trying to reconnect to the currently
"connected" network (assuming old scan results are not current enough to
skip the scan completely). This allows the scan result to come back in
much faster time. In ath9k, the scan took around 12 seconds with full
background scan, and only 0.1 second with the single-channel single-ssid
scan. Thus, take much less time for the client to re-establish
connection with the currently "connected" network.

Signed-hostap: Peter Qiu <zqiu@chromium.org>
2014-03-11 19:38:01 +02:00
Alexander Bondar
5e3ddf4d23 PNO: Change sched_scan_stopped event to handle pending PNO properly
When a sched_scan_stopped event is received and there is a pending PNO,
it used regular scheduled scan parameters instead of PNO specific
parameters. Change it by calling wpas_start_pno().

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-03-11 19:15:48 +02:00
Alexander Bondar
737e7a08b0 PNO: Move and rename pno_start()/pno_stop()
Move pno_start() and pno_stop() to scan.c as a more relevant location
and rename them to wpas_start_pno()/wpas_stop_pno().

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-03-11 19:12:57 +02:00
Jouni Malinen
95a3ea9426 HS 2.0R2: Add WNM-Notification Request for Subscription Remediation
Subscription remediation notification WNM-Notification Request is now
shown in the following way in wpa_supplicant control interface:
<3>HS20-SUBSCRIPTION-REMEDIATION http://example.com/foo/

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:23 +02:00
Jouni Malinen
f9cd147d6b HS 2.0R2: Update Indication element to Release 2
The HS 2.0 Indication element from wpa_supplicant now includes the
release number field and wpa_supplicant shows the release number of the
AP in STATUS command (hs20=1 replaced with hs20=<release>).

The new update_identifier field in the cred block can now be used to
configure the PPS MO ID so that wpa_supplicant adds it to the Indication
element in Association Request frames.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:22 +02:00
Andrei Otcheretianski
b3253ebb73 wpa_supplicant: Complete radio works on disable event
While testing rfkill blocking of a scanning interface, it
was seen that the ongoing scan never completes. This happens
since EVENT_SCAN_RESULTS is discarded on a disabled interface.

Fix this and also other possible radio work completion issues
by removing all the radio works (including started) of the
disabled interface.

To be able to remove already started radio works, make their
callbacks be reentrant with deinit flag (when the work
is started), so each radio work should be able to handle
its own termination.

Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2014-02-16 00:06:23 +02:00
Eytan Lifshitz
fd67275b85 wpa_supplicant: Fix wrong size memory allocation
Fix memory allocation in wpa_scan_clone_params(), where the
allocation request used the size of a pointer rather than the
size of the structure.

Signed-hostap: Eytan Lifshitz <eytan.lifshitz@intel.com>
2014-01-30 13:59:29 +02:00
Raja Mani
cf70d2981d wpa_supplicant: Schedule PNO on completion of ongoing sched_scan
When start PNO request comes from control interface, wpa_supplicant
should wait until ongoing sched_scan (triggered by wpa_supplicant)
gets cancelled. Issuing cancel sched_scan and start PNO scan
one after another from pno_start() would lead wpa_supplicant to clear
wps->sched_scanning flag while getting sched_scan stopped event
from driver for cancel sched_scan request. In fact, PNO scan will
be in progress in driver and wpa_s->sched_scanning will not be set
in such cases.

In addition to this change, RSSI threshold limit is passed as part of
start sched_scan request. This was previously set only in pno_start(),
but the same parameter should be available for generic sched_scan calls
as well and this can now be reached through the new PNO start sequence.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-22 19:41:45 +02:00
Raja Mani
dd271857a5 Skip normal scan when PNO is already in progress
Scan request failures are observed in wpa_supplicant debug log when
Android framework starts PNO scan in driver via ctrl interface command
'set pno 1' and wpa_supplicant also tries to issue a scan request after
PNO has started in the driver.

Some drivers may reject a normal scan request when PNO is already in
progress. wpa_supplicant should consider PNO status before issuing start
scan request to the driver. Otherwise, wpa_supplicant will get failures
from driver for the scan request and it will end up rescheduling scan
request in periodic interval and get a start scan request failure for
each attempt.

In order to avoid unnecessary scan attempt when PNO scan is already
running, PNO status is checked before issuing scan request to driver.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-21 16:19:49 +02:00
Jouni Malinen
a09ffd5f2f Fix req_scan-deplete-timeout and update eloop API for this
Commit e2f5a9889a was supposed to prevent
new scan request from pushing out the old one. However, it did not
really do that since eloop_deplete_timeout() returned 0 both for the
case where the old timeout existed (and was sooner) and if the old
timeout did not exist. It returned 1 only for the case where an old
timeout did exist and was larger than the new requested value. That case
used to result in wpa_supplicant_req_scan() rescheduling the timeout,
but hew code in eloop_deplete_timeout() did the exact same thing and as
such, did not really change anything apart from the debug log message.

Extend the eloop_deplete_timeout() (and eloop_replenish_timeout() for
that matter since it is very similar) to return three different values
based on whether the timeout existed or not and if yes, whether it was
modified. This allows wpa_supplicant_req_scan() to schedule a new
timeout only in the case there was no old timeout.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:10 +02:00
Jouni Malinen
6428d0a71f Do not start wpa_radio work during externally triggered scan
If an external program triggers a scan, wpa_supplicant does not have a
wpa_radio work item for this operation to protect against other
offchannel operations. This can result in operations failing, so try to
avoid damage by not starting any new wpa_radio work items during a scan
that was started by another process.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:10 +02:00
Jouni Malinen
6470f471e4 Remove unneeded scan delay on connection-in-progress
This type of protection against concurrent connection and scan
operations is now enforced through the wpa_radio work mechanism, so this
separate protection mechanism is not needed anymore.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:09 +02:00
Jouni Malinen
b9e6d7001d Use radio work for GAS requests
Avoid concurrent GAS operations with any other exclusive use of the
radio by using the radio work queuing mechanism. This replaces some of
the earlier constraints on concurrent operations with the more generic
wpa_radio work concept.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:09 +02:00
Jouni Malinen
1b5d4714dd Use radio work for P2P scan requests
Avoid concurrent P2P scan requests with any other exclusive use of the
radio by using the radio work queuing mechanism. This removes some of
the earlier workarounds that postponed scans depending on other
operations.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-05 22:39:25 +02:00
Jouni Malinen
d12a51b5d2 Use radio work for scan requests
Avoid concurrent scan requests by using the radio work queuing
mechanism.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-05 22:37:50 +02:00
Jouni Malinen
dd43aaa509 Add helper functions for cloning and freeing scan parameters
Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-05 22:35:52 +02:00
Jouni Malinen
9b850799c1 Fix scan-cache-clearing operation to avoid unnecessary cases
wpa_drv_scan() success case was supposed to clear
wpa_s->clear_driver_scan_cache, not params->only_new_results (which
would do nothing here).

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-03 08:55:51 +02:00
Jouni Malinen
949938aadf Ask driver to report only new scan results if requested
If the BSS table within wpa_supplicant is flushed, request the driver to
flush its own scan result table during the next scan. This can avoid
unexpected old BSS entries showing up after BSS_FLUSH or FLUSH command
in cases where the driver may maintain its internal cache of scan
results (e.g., cfg80211 BSS table persists at least for 15 seconds).

In addition to doing this automatically on BSS_FLUSH/FLUSH, a new SCAN
command argument, only_new=1, can be used to request a manual scan
request to do same. Though, it should be noted that this maintains the
BSS table within wpa_supplicant. BSS_FLUSH followed by SCAN command can
be used to clear all BSS entries from both the driver and
wpa_supplicant.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-02 23:03:31 +02:00
Jouni Malinen
3187fd900d WPS: Replace wpas_wps_in_progress with identical wpas_wps_searching
There is no point in maintaining two different functions that do
practically the same check of WPS state.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-29 17:59:12 +02:00
Jouni Malinen
662b40b16b WPS: Reduce scan wait time during WPS processing
Since the AP is expected to be available, there is no need to wait for
the full five second wait between scans during WPS connection. This
speeds up cases where the first scan misses the AP for some reason.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-12-26 20:50:28 +02:00
Jouni Malinen
1cd93ff743 Reschedule own scan request if an externally started one is in progress
This avoids some unnecessary attempts to request the driver to start a
scan while it is still busy with the scan operation that was started by
an external program.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 18:48:52 +02:00
Jouni Malinen
d81c73be18 Optional scan id for ctrl_iface SCAN requests
This allows users of wpa_supplicant control interface to figure out when
their specific scan command has been started and completed. For example:

CTRL-EVENT-SCAN-STARTED
> scan freq=2412,2417 passive=1 use_id=1
3
CTRL-EVENT-SCAN-RESULTS
CTRL-EVENT-SCAN-STARTED id=3
CTRL-EVENT-SCAN-RESULTS id=3

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 18:48:52 +02:00
Jouni Malinen
a5f40eff18 Track whether scan was started by us or an external program
This can be used to improve scan behavior in cases external programs
request scans directly from the driver.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 18:27:48 +02:00
Jouni Malinen
88c2d48860 Allow passive scan to be requested with SCAN passive=1
This allows external programs to request wpa_supplicant to execute
a passive scan (i.e., do not send any Probe Request frames).

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 18:27:48 +02:00
Jouni Malinen
fee5234284 Allow channel list to be specified for SCAN command
The new freq=<frequency ranges> parameter to the SCAN command can be
used to request a scan to be performed on the specified set of channels
instead of on all channels. For example, "wpa_cli scan
freq=2400-2500,5180" would scan channels 1-14 and 36. Only the channels
that the driver indicates as enabled and that are within the specified
ranges are included in the request.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 16:55:44 +02:00
Jouni Malinen
98eda9c26d Move int_array helpfer functions to utils/common.c
These can be useful outside scan.c, so make them available.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 13:37:06 +02:00
Johannes Berg
acb69cec6f wpa_supplicant: Use monotonic time for RX/BSS times
The BSS table, scan timeout, and related functionality should use
monotonic time since they care about relative values (age) only.
Unfortunately, these are all connected, so the patch can't be split
further. Another problem with this is that it changes the driver wrapper
API. Though, it seems only the test driver is using this.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-12-24 07:27:02 +02:00
Loic Poulain
1245503188 Restore scan_req if sta scan is rescheduled in the scan results event
On scan results event if a concurrent P2P scan was triggered previously,
scan results processing is canceled, p2p_find executed, and a new sta
scan is triggered (pending scan). However, this new sta scan does not
restore the scan_req value of the previous scan (whose scan result has
been canceled).

If we are currently connected to an AP and use ap_scan=2, the new
triggered scan will cause an associtation-without-scan in
wpa_supplicant_scan:
(ap_scan == 2 & scan_req != MANUAL_SCAN_REQ)
	=> wpa_supplicant_assoc_try()
causing an association error and a disconnection.

This patch fixes this issue by restoring the previous scan_req value.

Signed-off-by: Loic Poulain <loicx.poulain@intel.com>
2013-11-24 11:47:30 +02:00
Johannes Berg
594516b4c2 Use monotonic clock for relative time for eloop if available
Relative time shouldn't be calculated based on gettimeofday
because that clock can jump (e.g., when the time is adjusted
by the system administrator.)

On systems where that is available, use CLOCK_BOOTTIME (on
fairly recent Linux systems, this clock takes into account
the time spend suspended) or CLOCK_MONOTONIC (on Linux and
some POSIX systems, this clock is just freely running with
no adjustments.)

Reported-by: Holger Schurig <holgerschurig@gmail.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-11-20 23:52:56 +02:00
Jithu Jance
f86d282f43 Handle legacy scan interruption of sched_scan/PNO
While starting from PNO start context, the scheduled scan was not
setting the flag wpa_s->scanning. This was resulting in the subsequent
SCAN command to proceed further and send command to nl80211/cfg80211.
The expected behavior of cancelling sched_scan was not happening here.

While sched_scan is in progress and a legacy scan comes on the
cli/socket, the sched_scan is cancelled and normal scan is allowed to
continue. However, sometimes sched_scan cancelled event comes a bit
delayed and we will send out the scan command before the wpa_s->scanning
is cleared. Instead, reschedule the incoming scan req if the
wpa_s->scanning shows that it is still in progress.

Signed-hostap: Jithu Jance <jithu@broadcom.com>
2013-11-18 14:35:48 +02:00
Jouni Malinen
fa58da2e6c Remove old mechanism of skipping scan request rescheduling
Since eloop_deplete_timeout() is doing practically same in
wpa_supplicant_req_scan(), revert the old mechanism from commit
7e1488494e to avoid unnecessary work in
this function.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-17 16:47:13 +02:00
Dmitry Shmidt
e2f5a9889a Deplete scan request if new time is less than remaining
This avoids pushing out previous scheduled scan requests based on new
events.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2013-11-17 16:46:58 +02:00
Jouni Malinen
9100b6607b P2P: Debug print reason for specific SSID for scan
It can be useful to see whether the specific P2P SSID was used for scan
based on p2p_in_provisioning or show_group_started when debugging issues
where this case shows up unexpectedly.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-11-01 10:30:50 +02:00
Pontus Fuchs
c6f5dec9c1 Don't start second scan when changing scan interval
If a scan is currently running and the scan interval is changed, a
second scan will be started before the current has finished. This will
in turn, if no networks are configured, cause wpa_s->state to be
forced to WPA_INACTIVE before the first scan has finished.

Signed-hostap: Pontus Fuchs <pontus.fuchs@gmail.com>
2013-10-22 15:57:21 +03:00
Jouni Malinen
cbc5484892 GAS: Do not start new scan operation during an ongoing GAS query
These operations can have conflicting offchannel requirements, so wait
with a new scan trigger until a pending GAS query has been completed.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-21 13:20:38 +03:00
Kyeyoon Park
c377514337 GAS: Delay GAS query Tx while scanning/connecting
Offchannel operations needed for a GAS query can conflict with ongoing
scan/connection progress, so delay GAS queries if such an operation is
in progress on the current interface or any virtual interface sharing
the same radio.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-21 13:15:45 +03:00
Jouni Malinen
aaeb9c98e6 P2P: Allow GO to be discovered based on Beacon frame
This fixes some P2P-join-a-group cases where GO may have been discovered
based on passive scan or non-P2P scan. P2P IEs may have been received
from a Beacon frame in such a case and that information can be used to
create a P2P peer entry, e.g., to allow provision discovery exchange to
be completed.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-14 19:25:28 +03:00
Ilan Peer
53c5dfc2c4 Change share_vif_oper_freq() to handle multiple freqs
There are devices that can operate several channels concurrently.
Change shared_vif_oper_freq() to get_shared_radio_freqs() that can
return an array of frequencies currently used by all the virtual
interfaces that share the same radio.

In addition, move it to wpa_supplicant.c, so it can be used by other
modules.

Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Signed-hostap: David Spinadel <david.spinadel@intel.com>
2013-07-21 20:03:53 +03:00
Chengyi Zhao
831770bffe Cancel delayed scheduled scan when wpa_supplicant cleans up
Because a delayed scheduled scan will access the members of struct
wpa_supplicant which is freed and this can result in a crash,
wpa_supplicant needs to cancel delayed scheduled scan during cleanups.

Signed-hostap: Chengyi Zhao <chengyix.zhao@gmail.com>
2013-07-20 17:47:02 +03:00
Jouni Malinen
faf9a8585d Add band option (2.4 vs. 5) for filtering scans
This can be used to implement filtering of channels for scan and based
on that, for connection, purposes.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-18 12:17:10 +03:00
Deepthi Gowri
36b9883d84 Defer scan if connection is in progress on any of the shared interfaces
Scanning can delay concurrent operations considerably, so it is better
to avoid that while trying to connect on any of the virtual interfaces
that share the same radio.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-10 16:10:50 +03:00
Ben Greear
6124e858fd wpa_supplicant: Allow vifs to scan only current channel
If a VIF is already associated, then only scan on the associated
frequency if user requests such. This is a big help when using
lots of virtual stations.

Signed-hostap: Ben Greear <greearb@candelatech.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
2013-05-09 12:43:40 +03:00
Sheng Fang
4aa8186806 Add a configration parameter for sched_scan interval
The new sched_scan_interval parameter can be used to set the default
sched_scan interval, e.g., for power saving purposes.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-07 12:41:14 +03:00
Ben Greear
f5ffc348dc wpa_supplicant: Allow global scan frequencies configuration
This allows one to limit the channels that wpa_supplicant will
scan. This is a useful addition to the freq_list configurable
in the network {} section.

Signed-hostap: Ben Greear <greearb@candelatech.com>
2013-05-05 11:46:54 +03:00
Jouni Malinen
0f105f9e5f HS 2.0: Move Probe Request Indication IE addition to proper place
This needs to be in wpa_supplicant_extra_ies() to get consistent
behavior for both scan and sched_scan cases.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-05-04 11:57:56 +03:00
Jouni Malinen
4342326fc7 Add ignore_old_scan_res configuration parameter
This can be used to configure wpa_supplicant to ignore old scan results
from the driver cache in cases where such results were not updated after
the scan trigger from wpa_supplicant. This can be useful in some cases
where the driver may cache information for a significant time and the AP
configuration is changing. Many such cases are for testing scripts, but
this could potentially be useful for some WPS use cases, too.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-03-31 18:05:42 +03:00
Jouni Malinen
407be00b6c P2P: Postpone P2P scan only if station mode scan is pending
sta_scan_pending was supposed to be accurate enough for determining
whether a P2P scan needs to be postponed. However, it has turned out
that there were cases where sta_scan_pending was not cleared properly.
While the known cases have now been addressed, it is possible that some
other cases may still exist. To avoid issues with P2P operationg getting
stuck, verify more carefully that there is a real pending station mode
scan (either in progress or scheduled to be requested).

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-03-18 17:32:31 +02:00
Jouni Malinen
b1cd021e29 P2P: Re-start P2P operation if station mode scanning is stopped
There were couple of code paths that could end up stopping station mode
scanning without clearing sta_scan_pending. This could result in P2P
search getting stuck waiting for completion of station mode scan which
would never show up. Fix this by calling wpas_p2p_continue_after_scan()
in cases where station mode scans are stopped. This allows
sta_scan_pending to be cleared and P2P search operation continued.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-03-18 17:32:31 +02:00
David Spinadel
7ed52f678b wpa_supplicant: Save prev_sched_ssid only if needed
If the whole ssid list was scanned, don't save the prev scheduled ssid
since we are going to start from beginning. Thos avoids starting sched
scan from prev_sched_ssid after scanning the full list, in case of
adding a network to ssid during scheduled scan.

Signed-hostap: David Spinadel <david.spinadel@intel.com>
2013-03-10 17:32:03 +02:00
David Spinadel
a09fc1ccf8 wpa_supplicant: Do not allow too short sched scan
In case that the ssid list is longer than max number of ssids,
ths scheduled scan aborted after timeout and rescheduled again
with shorter timeout and longer interval. In case that the timeout
is shorter than the interval, only one scan iteration will
be run. In this case, go back to the initial values.

Signed-hostap: David Spinadel <david.spinadel@intel.com>
2013-03-10 17:27:48 +02:00
Jouni Malinen
c5f10e804a Use more accurate timestamps for scan results
For various P2P use cases, it is useful to have more accurate timestamp
for the peer information update. This commit improves scan result
handling by using a single timestamp that is taken immediately after
fetching the results from the driver and then using that value to
calculate the time when the driver last updated the BSS entry. In
addition, more debug information is added for P2P peer updates to be
able to clearly see how old information is being used here.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-02-12 19:14:32 +02:00
Dmitry Shmidt
66fe0f703c Add 'SCAN TYPE=ONLY' functionality
Usual manual scan request may cause reassociation due to several
reasons. New command is intended to perform pure scan without taking any
automatic action based on the results.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2013-02-07 18:09:50 +02:00
Jouni Malinen
5ebe8c8179 HS 2.0: Fix IE buffer length for extra scan IEs
The HS 2.0 Indication element is 7 (not 6) octets. The previous
implementation could result in wpabuf validation code stopping the
program if HS 2.0 was enabled without Interworking or P2P (which would
have created a large enough buffer to avoid hitting this) being enable.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-02-05 17:40:09 +02:00
Pontus Fuchs
9e737f08d4 Update scan interval gracefully
When the scan interval is changed the new interval is effective
after the old interval timer fires off one last time. This can cause
an unacceptable long delay when updating the interval.

Change this behaviour to use MIN(left of old interval, new interval)
for the scan interval following the interval change.

Signed-hostap: Pontus Fuchs <pontus.fuchs@gmail.com>
2013-02-03 18:14:05 +02:00
Jouni Malinen
e4296380e0 Remove unused wpa_scan_get_vendor_ie_multi_beacon()
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-27 12:31:06 +02:00
Jouni Malinen
2c09af3068 Add Doxygen documentation for functionality related to scanning
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-27 12:29:05 +02:00
Jouni Malinen
4115303bbe Document wpa_s->scan_req
Use an enum with documented values to make it easier to understand how
wpa_s->scan_req is used.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-11-25 15:55:32 +02:00
Jouni Malinen
5cc7032239 P2P: Avoid multi-channel scans when they are not needed
If the driver does not support multi-channel concurrency and a virtual
interface that shares the same radio with the current interface is
operating there may not be need to scan other channels apart from the
current operating channel on the other virtual interface. Filter out
other channels in case we are trying to find a connection for a station
interface when we are not configured to prefer station connection and a
concurrent operation is already in process.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-11-25 12:47:43 +02:00
Jouni Malinen
23270cd8f5 Restore wpa_s->scan_req if scan trigger fails
If the driver rejects the scan request while handling an external
requested scan (e.g., SCAN command on ctrl_iface), wpa_s->scan_req gets
cleared in wpa_supplicant_scan(). This can results in issues when the
scheduled re-try of the scan in one seconds trigger another call to this
function. If ap_scan==2 mode is used, this would result in new
association attempt instead of a new scan. Avoid this by restoring value
of wpa_s->scan_req in case the scan trigger fails and a new scan attempt
is scheduled.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-10-30 12:27:05 +02:00
Jouni Malinen
7a808c7eb7 P2P: Allow P2P functionality to be disabled per interface
By default, P2P is enabled globally for all virtual interfaces and this
makes wpa_supplicant include WSC and P2P IEs in Probe Request frames for
all scans even if this is for a non-P2P station connection to speed up
device discovery. If an interface is dedicated for non-P2P station mode
operations, it is now possible to disable addition of WSC and P2P IEs
into Probe Request frames with a per-interface p2p_disabled parameter.
This can be set either in the configuration file (p2p_disabled=1) or at
run time ("wpa_cli -i wlan0 set p2p_disabled 1"). Unlike the previous
mechanism ("wpa_cli p2p_set disabled 1"), the new parameter changes the
behavior only for the specified interface while other interfaces
continue to follow the global P2P enabled/disabled state.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-10-10 13:08:23 +03:00
Jouni Malinen
4c490780e2 P2P: Fix pending-sta-scan processing for concurrent operation cases
If two P2P_FIND commands and a station mode SCAN command are issued in a
sequence with the second P2P_FIND and SCAN commands started before the
initial scan from the first P2P_FIND command has completed,
sta_scan_pending may be left set without an automatic way of getting it
cleared. This can get P2P search stuck if no further station mode scan
operations are run.

Fix this by clearing the sta_scan_pending flag whenever station mode scans
are stopped due to no enabled networks resulting in INACTIVE mode getting
entered. In addition, avoid setting sta_scan_pending flag when a special
scan_res_handler is set so that this does not get enabled on the P2P
Device interface during a P2P search operation.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-09-24 13:46:27 +03:00
Jouni Malinen
ac06fb12f5 P2P: Add more debug prints for GO start routines
This makes it easier to debug issues in starting GO mode.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-09-24 01:05:51 +03:00
Jouni Malinen
d4534bde9c Add debug print for no-enabled-networks case
If there are any disabled networks, show a debug print with the count
of those networks when no enabled networks are found. This can be
helpful in trying to figure out why scans are being skipped.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-09-24 01:04:00 +03:00
Jouni Malinen
e665ca9a8d P2P: Move p2p_cb_on_scan_complete to global context
Since we have a global P2P module, the flag to trigger scan completion
events to it needs to be in similar context. The previous design
maintained this separately for each virtual interface and if P2P module
did not run its scan operation on the virtual interface that completed
the scan, P2P module would not be allowed to restart operations
properly.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-09-13 17:58:22 -07:00
Jouni Malinen
4d5bda5fca Interworking: Add optional use of network selection on normal scans
auto_interworking=1 configuration parameter can be used to request
wpa_supplicant to use Interworking network selection automatically as a
part of the normal (non-Interworking) network selection if the scan
results do not match with enabled networks. This makes scanning work
similarly to the "interworking_select auto" command.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-28 16:14:13 +03:00
Jouni Malinen
99fcd40409 P2P: Allow scan operations during p2p_find
Previously, all station mode scan operations were either skipped or
delayed while any P2P operation was in progress. To make concurrent
operations easier to use, reduce this limitation by allowing a scan
operation to be completed in the middle of a p2p_find. In addition,
allow station mode association to be completed. When the station mode
operation is run to its completion (scan results not acted on,
connection to an AP completed, connection failed), resume the p2p_find
operation.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-23 19:42:53 +03:00
Eyal Shapira
a13e07ec4d Fix adding extra IEs in sched scan
Refactoring done in commit 46ee0427b1
(IEEE 802.11u: Allow Interworking and HESSID to be configured)
broke adding extra IEs in sched scan. The IEs stopped being added
to the scan params within wpa_supplicant_extra_ies() but no code
was added to add them in wpa_supplicant_req_sched_scan().
Fix this and remove unused params arg in wpa_supplicant_extra_ies().

Signed-hostap: Eyal Shapira <eyal@wizery.com>
intended-for: hostap-1
2012-08-13 21:48:55 +03:00
Jouni Malinen
067ffa2696 Convert os_realloc() for an array to use os_realloc_array()
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-13 21:21:23 +03:00
Jouni Malinen
b9b12d02f0 autoscan: Fix potential freeing of uninitialized pointer
Commit 7c865c6853 introduced a code
path that can skip extra_ie initialization in wpa_supplicant_scan().
This could result in semi-random crashes when using the autoscan
mechanism. Fix this by initializing extra_ie to NULL.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-07-03 20:54:40 +03:00
Tomasz Bursztyka
7c865c6853 Add automatic scanning support
Like bgscan, autoscan is an optional module based feature to automate
scanning but while disconnected or inactive.

Instead of requesting directly a scan, it only sets the scan_interval
and the sched_scan_interval. So, if the driver supports sched_scan,
autoscan will be able to tweak its interval. Otherwise, the tweaked
scan_interval will be used. If scan parameters needs to be tweaked, an
autoscan_params pointer in wpa_s will provide those. So req_scan /
req_sched_scan will not set the scan parameters as they usually do, but
instead will use this pointer.

Modules will not have to request a scan directly, like bgscan does.
Instead, it will need to return the interval it wants after each
notification.

Signed-hostap: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2012-06-26 18:55:41 +03:00
Jouni Malinen
1cbe86e2d6 Add debug prints of scan result IEs
Excessive debug level can now be used to dump the IEs received in scan
results from both Beacon and Probe Response frames. This makes it easier
to debug issues where the driver (or well, more likely cfg80211) does
not update the IEs based on Beacon frames if even a single Probe
Response frame has been received.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-11 15:30:05 +03:00
Jouni Malinen
349493bd0c Validate WEP key lengths based on driver capabilities
The nl80211 driver interface does not allow 128-bit WEP to be used
without a vendor specific cipher suite and no such suite is defined for
this purpose. Do not accept WEP key length 16 for nl80211 driver
interface forn ow. wext-interface can still try to use these for
backwards compatibility.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-10 14:34:46 +03:00
Jay Katabathuni
c923b8a537 HS 2.0: Add Hotspot 2.0 indication into Probe Request
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-08 23:29:58 +03:00
Jouni Malinen
fea7c3a055 Ignore network blocks that have invalid WEP key length
Do not try to associate with a network that has an invalid or incomplete
configuration because the association or at least data connection would
fail anyway. This commits adds a common function for checking whether a
network block is disabled to make it easier to check network blocks
without having to reject them during configuration file parsing (which
would prevent wpa_supplicant from starting). The only additional check
added in this commit is to verify the WEP key length. Similar checks for
other parameters can be added in future commits.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-07 13:39:33 +03:00
Jouni Malinen
b55aca4672 Fix sched_scan for max-num-of-scan_ssid=1 networks
When the network configuration includes exactly the number of
scan_ssid=1 networks as the driver supports for scan_sched and no
networks need wildcard SSID scan, there is no need to use sched_scan
timeout. Check this condition and optimize this case to avoid the extra
sched_scan start/stop operations.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-17 16:51:09 +03:00
Jouni Malinen
7d21a223f1 Fix sched_scan debug print regarding timeout
The debug messages were showing the opposite of what the actual
implementation was doing for sched_scan timeout.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-17 16:32:40 +03:00
Jouni Malinen
54ddd74369 Add disable_scan_offload parameter to disable automatic scan offloading
This new configuration parameter can be used to disable automatic
offloading of scan requests to the driver which was previously used
by default if the driver supported sched_scan.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-17 16:30:15 +03:00
Jouni Malinen
85ea132a13 P2P: Use scan optimization for post-provisioning connection
Since P2P GO cannot change the SSID after WPS provisioning step, we
can use the specific SSID for the scan for data connection. In addition,
mark this as p2p_probe to avoid unnecessary use of 802.11b rates.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-02-29 00:34:53 +02:00
Jouni Malinen
a21c05db23 P2P: Use specific SSID in scan for provisioning step
Since the P2P client learns the SSID of the group during GO Negotiation,
use the specific SSID in the Probe Request frames during the
provisioning step. This helps in avoiding unnecessary Probe Response
frames from other P2P GOs or APs.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-02-29 00:02:34 +02:00
Jouni Malinen
360182ed7c P2P: Advertise immediate availability of WPS credential
Use Device Password ID in WSC IE of Probe Request and Probe Response
frames to advertise immediate availability of WPS credentials per P2P
specification sections 3.1.2.1.1 (Listen State), 3.1.2.1.2 (Scan Phase),
and 3.1.2.1.3 (Find Phase).

For now, the Device Password ID is set only for the case where we are
active GO Negotiation with a specific peer. In practice, this means that
the Probe Response frames during pending GO Negotiation (whenever in
Listen state) indicate availability of the credential.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-02-27 23:14:35 +02:00
Jouni Malinen
d445a5cd8e Add BSSID filter for testing purposes
wpa_supplicant can now be configured to filter out scan results based
on a BSSID filter. Space-separated set of allowed BSSIDs can be set
with wpa_cli set bssid_filter command. Filtering mechanism can be
disabled by setting this variable to an empty list. When set, only
the BSSes that have a matching entry in this list will be accepted
from scan results.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-02-16 16:30:13 +02:00
Jouni Malinen
aa283ddd97 WPS: Do not use sched_scan for provisioning step
Normal scan is more reliable and faster for WPS operations and since
these are for short periods of time, the benefit of trying to use
sched_scan would be limited. This can fix WPS connectivity issues
with some drivers.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
2012-02-15 20:41:42 +02:00
Jouni Malinen
0f3d578efc Remove the GPL notification from files contributed by Jouni Malinen
Remove the GPL notification text from the files that were
initially contributed by myself.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-02-11 19:39:36 +02:00
Eyal Shapira
b3aa456b3e Interleave wildcard and specific SSID scans when max_ssids=1
For drivers limited to scan a single SSID at a time, this prevents
waiting too long for a wildcard scan in case there are several
scan_ssid networks in the configuration.

Signed-hostap: Eyal Shapira <eyal@wizery.com>
2012-01-29 17:39:08 +02:00
Jouni Malinen
b21ff9cb20 P2P: Fix WSC IE inclusion for P2P disabled case
wpas_wps_in_use() was forcing WPS to be enabled unconditionally if P2P
support was included in the build. This is not really the correct
behavior for the case when P2P has been disabled at runtime. Change the
code here to verify runtime configuration of P2P before forcing WPS to
be enabled. This allows WSC IE to be left out from Probe Request frames
when scanning for APs without P2P or WPS being in use.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-01-27 21:09:34 +02:00
Jouni Malinen
1e7fb4f1b7 WPS: Use single channel scan if AP channel already known
If the BSSID of the AP is specified in the WPS command, the target
AP is likely already in the BSS table and its operating channel is
known. Use this information to speed up connection by only scanning
the known channel.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-31 13:17:20 +02:00
Jouni Malinen
76202aed23 Fix compiler warning with CONFIG_NO_STDOUT_DEBUG=y
Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-11 18:13:51 +02:00
Jouni Malinen
ea5bae4731 Increase min sched_scan interval from 2 to 10 seconds
Trying to run sched_scan round every two seconds by defaults sounds way
too frequent since dualband cards are unlikely to be able to complete
the full scan cycle in two seconds. For now, set the hardcoded value to
10 seconds to make this somewhat more reasonable.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-29 20:05:58 +02:00
Jouni Malinen
0b7a25c00f Use normal scan before sched_scan if that can speed up connection
When normal scan can speed up operations, use that for the first three
scan runs before starting the sched_scan to allow user space sleep more.
We do this only if the normal scan has functionality that is suitable
for this or if the sched_scan does not have better support for multiple
SSIDs.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-28 18:36:36 +02:00
Jouni Malinen
76a5249e52 Add broadcast SSID for sched_scan for scan_ssid=0 networks
Previously, only networks with scan_ssid=1 were included in sched_scan.
This needs to behave similarly to the normal scan where broadcast SSID
is used to find networks that are not scanned for with a specific SSID.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-28 18:12:38 +02:00
Jouni Malinen
5edddf4175 Use common code for disabled network case in sched_scan
There is no need to implement two copies of the iteration code here.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-28 18:09:37 +02:00
Jouni Malinen
86b47aaf36 Drop sched_scan filter if not enough match sets supported
Instead of including only a single SSID in the sched_scan request if
the driver does not support match sets, just drop the SSID filter and
configure more SSIDs up to the sched_scan limit.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-28 17:52:36 +02:00
Jouni Malinen
a8cb5a8897 Make sched_scan debug clearer on timeout use
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-28 17:52:02 +02:00
Jouni Malinen
7c6a266ced Fix sched_scan filter_ssids setting for no filters case
The filter_ssids pointer needs to be set to NULL if no SSID filters
are set to avoid filtering out all scan results.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-28 15:19:41 +02:00
Jouni Malinen
fcd1684787 Fix sched_scan filter setting for max_match_sets == 0
The previous implementation was trying to add the first SSID
to a zero-length array. Avoid this with an explicit validation
of the array length.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-25 18:12:04 +02:00
Jouni Malinen
3f56f3a496 Do not try to add wildcard SSID into active sched_scan
Even though scan_ssid should not really be set for wildcard SSID,
better verify that here explicitly insead of assuming that the
SSID is set.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-11-19 17:01:53 +02:00
Eyal Shapira
1966e3d1b7 sched scan: Fix passive scanning
Scan wasn't initiated in case the config contained only networks without
scan_ssid. In such a case we want scan to be initiated without any SSIDs
to actively scan but include all the SSIDs in the filter list. Also
added some debug logs to easily see which SSIDs were included in which
list.

Cc: Luciano Coelho <coelho@ti.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
2011-11-18 23:05:57 +02:00
Jouni Malinen
aa820e02cc Clean up debug dump for scan results sorting
There is not much need for showing the interim qsort steps, so just show
the ordered results.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-10-30 21:08:34 +02:00
Gary Morain
577db0aedd Prefer 5 GHz networks over 2.4 GHz networks
In scan.c, merge a channel's noise value into the scan results. When
comparing scan results, compute the signal-to-noise ratio and use it
when available. Prefer a 5 GHz network if its SNR is really big (> 30)
or if its SNR is relatively close to the other network's.
2011-10-30 21:08:21 +02:00
Jouni Malinen
d1dd48e3c9 P2P: Indicate scan during group formation as P2P probe
The interface may not yet have been set to P2P client mode immediately
after GO Negotiation when doing the scan before association request.
Consequently, the scan request in this state has to specify that the
specific P2P probe mode is used to disable IEEE 802.11b rates.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-10-29 23:02:47 +03:00
Jouni Malinen
17fbb751e1 Remove user space client MLME
This code was used only with driver_test.c to allow MLME operations
in hostapd to be tested without having to use a real radio. There
are no plans on extending this to any other use than testing and
mac80211_hwsim has now obsoled the need for this type of testing.
As such, we can drop this code from wpa_supplicant to clean up the
implementation of unnecessary complexity.
2011-10-22 22:45:38 +03:00
Jouni Malinen
9e0e6902a2 Share a single wpa_scan_results_free() implementation
There is not really a very good location for this anywhere, but the
function is small enough to live as an inline function for now.
2011-10-22 22:09:40 +03:00
Jouni Malinen
11540c0b21 Interworking: Allow ANT to be configured for Probe Request frames
Access Network Type can now be configured (default: 15 = wildcard) to
limit which APs reply to the scan.
2011-10-21 12:44:29 +03:00
Jouni Malinen
46ee0427b1 IEEE 802.11u: Allow Interworking and HESSID to be configured
The new wpa_supplicant.conf file global parameters interworking and
hessid can be used to configure wpa_supplicant to include
Interworking element in Probe Request frames.
2011-10-16 23:55:34 +03:00
Luciano Coelho
6a90053cdf Add delayed scheduled scan request
When initializing, the scheduled scan code was being called before
everything is ready. With normal scans, the first scan round is
delayed, so the initialization is finished by the time it really
starts.

Add a function that can be used to request a delayed scheduled scan.
The scan will only start after the specified time has elapsed. Call
this function instead of starting the scheduled scan directly during
driver initialization.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-10-15 18:53:14 +03:00
Luciano Coelho
b59e6f267b Add filter support to scheduled scans
Pass SSIDs to be matched in scheduled scan results. Only the SSIDs
that are included in the match lists will be reported by the driver,
so the filtering can be offloaded to the hardware and the power
consumption can be reduced.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-10-15 18:53:14 +03:00
Luciano Coelho
cbdf3507e9 Add scheduled scan driver operations
In new Linux kernel versions (>=3.0), nl80211 adds scheduled scan
capability. In order to use this feature to its full extent, we need
to support it in the wpa_supplicant core, so that it can also be used
by other drivers.

This commit adds initial scheduled scan support operations and events.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-10-15 18:53:13 +03:00
Luciano Coelho
5f738a21a6 Reorganize P2P and WPS scan code
Move some code to separate functions to reorganize the P2P and WPS
handling during scans. This makes the code a bit cleaner and is
needed for the scheduled scan implementation to avoid duplicated code.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-10-15 18:53:13 +03:00
Jouni Malinen
206e1f422f P2P: Provide mechanism for figuring out p2p_scan_ie() buffer need
The new function, p2p_scan_ie_buf_len(), can be used to figure out
how large a buffer needs to be allocated for p2p_scan_ie() use. This
makes it easier to add new data into the buffer without forcing all
callers to be updated to use a larger buffer.
2011-09-29 22:18:23 +03:00
Jouni Malinen
303f60d39b P2P: Do not request station mode scans during P2P operations
The P2P search mechanism depends on the same scan functionality that
is used for station mode scans. If these operations are being used
at the same time, scan result processing is not handled properly.
Avoid unexpected behavior by delaying station mode scan requests
if a P2P operation is in progress.

Among other things, this allows the station mode connection attempt
to be continued after a P2P find or group formation has been completed
if the interface is available (i.e., when the P2P group uses a
separate virtual interface).
2011-09-29 16:53:55 +03:00
Jouni Malinen
7dcdcfd68d P2P: Start GO without extra scan step
There are some corner cases, where the wpa_supplicant_req_scan() call
may end up scheduling a scan even if we are about to start a GO. Avoid
this by explicitly marking the GO network to be selected for the next
connection.
2011-06-21 11:47:03 +03:00
Jean-Michel Bachot
046ef4aa67 P2P: Add option for requested device type in P2P search/scan
With this, p2p_find can be extended to find certain requested device
types.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-03-19 12:57:46 +02:00
Ben Greear
f049052b9e Use wpa_msg() instead of wpa_printf()
This converts number of debugging messages to use wpa_msg() in order
to allow the interface name to be shown with the messages.

A new function, wpa_dbg(), is introduced to allow
CONFIG_NO_STDOUT_DEBUG=y builds to remove the debug strings. This is
otherwise identical with wpa_msg(), but it gets compiled out if stdout
debugging is disabled.
2011-02-10 20:14:46 +02:00
Jouni Malinen
5471c3434e Blacklist BSS on first failure if only a single network is enabled
The special case of requiring blacklisting count to be 2 or higher
is only needed when more than a single network is currently enabled.
As such, we should not do that when only a single network is enabled.
This make the station more likely to follow network side load
balancing attempts where the current AP may disassociate us with
an assumption that we would move to another AP.
2010-11-26 11:23:50 +02:00
Jouni Malinen
f47d639d49 SME: Optimize recovery from common load balancing mechanisms
When authentication or association fails when trying to connect to
a BSS in an ESS that has multiple BSSes based on previous scans,
limit the first recovery scan to only the known channels that has
been seen previously. This speeds up recovery in some of the most
commonly used load balancing mechanisms in enterprise WLAN
networks.
2010-11-25 22:51:56 +02:00
Jouni Malinen
2af1c18735 P2P: Scan all channels if GO is not found from common channels
This is not supposed to happen, but in theory, the GO may end up
changing its channels at some point. While it would be reasonable
to use one of the common channels, GO may be forced to use another
channel. The most likely reason for this would be if the P2P client
is enforcing only a single channel to be used (e.g., to avoid
multi-channel concurrent operations).
2010-10-19 18:38:49 +03:00
Jouni Malinen
af8ab1ae97 P2P: Use 'Enrollee info' WPS request type in P2P scans
This avoids setting explicit Request-to-Enrollee request when
WPS 2.0 is used.
2010-09-09 07:17:20 -07:00
Jouni Malinen
0817de904e P2P: Optimize scan timeouts for group formation 2010-09-09 07:17:17 -07:00
Jouni Malinen
0e65037c27 P2P: Add P2P IE into Probe Request frames 2010-09-09 07:17:17 -07:00
Jouni Malinen
54f489be45 WPS 2.0: Validate WPS attributes in management frames and WSC messages
If CONFIG_WPS_STRICT is set, validate WPS IE(s) in management frames and
reject the frames if any of the mandatory attributes is missing or if an
included attribute uses an invalid value. In addition, verify that all
mandatory attributes are included and have valid values in the WSC
messages.
2010-09-09 06:07:48 -07:00
Masashi Honma
509a39727f WPS: Fix unused variable warning
The wpa_supplicant compilation without CONFIG_WPS option results in
messages below.

scan.c: In function 'wpa_supplicant_scan':
scan.c:246: warning: unused variable 'wps'

This trivial patch erases this warning.
2010-08-20 09:44:50 +03:00
Jouni Malinen
24f7694062 Remove get-first-scan-results-before-request optimization
This has already been disabled in most use cases and can result
in problems with some drivers, so better just remove it completely.
2010-07-18 16:11:03 -07:00
Jouni Malinen
4436274bef SME: Do not skip initial scan request
When SME is in wpa_supplicant (mac80211), we need to make sure that
the kernel code has valid BSS entry for the AP. In some cases it
seemed to be possible to end up not having current information in
cfg80211 or mac80211 which can result to association failures. Avoid
this by always running through the scan request before initial
connection attempt.
2010-07-17 20:28:22 -07:00
Jouni Malinen
41e650ae5c WPS: Use different scan result sorting rules when doing WPS provisioning
The AP configuration may change after provisioning, so it is better
not to use the current security policy to prioritize results. Instead,
use WPS Selected Registrar attribute as the main sorting key and use
signal strength next without considering security policy or rate sets.
The non-WPS provisioning case remains as-is, i.e., this change applies
only when trying to find an AP for WPS provisioning.
2010-06-11 13:50:13 -07:00
Jouni Malinen
d902a9c1bc Fix scan_runs counting
Addition of the background scanning mechanism in commit
60b94c9819 moved the scan trigger
into a new function that was also incrementing the scan_runs
counter, but the removal of the previous scan_runs incrementation
was forgotten from that patch. This counter should only be updated
into a single location, so remove the old one. This improves AP
selection for WPS provisioning by not skipping some of the initial
scans.
2010-06-11 11:15:16 -07:00
Jouni Malinen
8401a6b028 Add Linux rfkill support
Add a new wpa_supplicant state: interface disabled. This can be used
to allow wpa_supplicant to be running with the network interface even
when the driver does not actually allow any radio operations (e.g.,
due to rfkill).

Allow driver_nl80211.c and driver_wext.c to start while rfkill is in
blocked state (i.e., when ifconfig up fails) and process rfkill
events to block/unblock WLAN.
2010-05-23 10:27:32 +03:00
Jouni Malinen
1c4c9c5078 Try to start a new scan more quickly after driver rejection
This speeds up recovery from some cases where the driver may refuse
a new scan request command temporarily.
2010-04-11 19:56:23 +03:00
Jouni Malinen
8cd82735cb Add an option to request a connection without a new scan 2010-04-11 19:55:40 +03:00
Jouni Malinen
17a4734dc4 Optimize post-WPS scan based on channel used during provisioning
Scan only the frequency that was used during provisioning during the
first five scans for the connection. This speeds up connection in the
most likely case where the AP remains on the same channel. If the AP is
not found after these initial scans, all channels will be scanned.
2010-04-11 19:06:42 +03:00
Jouni Malinen
3812464cda Add optional scan result filter based on SSID
filter_ssids=1 global configuration parameter can now be used to
enable scan result filtering (with -Dnl80211 only for now) based on
the configured SSIDs. In other words, only the scan results that have
an SSID matching with one of the configured networks are included in the
BSS table. This can be used to reduce memory needs in environments that
have huge number of APs.
2010-03-05 21:42:06 +02:00
Jouni Malinen
207ef3fb12 Add suspend/resume notifications
wpa_supplicant can now be notified of suspend/resume events, e.g.,
from pm-action scripts. This allows wpa_supplicant to clear information
that may become invalid during a suspend operation.
2010-02-27 18:46:02 +02:00
Jouni Malinen
d1f9c410c1 Remove src/drivers/scan_helpers.c
Most of this file was already moved into wpa_supplicant/scan.c and
we can remove the file completely by having couple of small helper
functions copied to the remaining users outside core wpa_supplicant
code.
2010-01-03 20:27:32 +02:00
Jouni Malinen
9ba9fa07cc Move wpa_supplicant specific scan code away from src/drivers
This fits better in wpa_supplicant/scan.c. Couple of remaining
scan_helpers.c functions are currently used in driver wrappers,
but they can likely be removed in the future.
2010-01-03 18:48:11 +02:00
Jouni Malinen
d009a9dac6 Add scan parameter support for client MLME 2009-12-28 13:34:03 +02:00
Jouni Malinen
c2e8d0a092 Remove deprecated scan and set_probe_req_ie driver_ops
These have been replaced with scan2 driver_ops that provides all
parameters in a single call.
2009-11-23 21:13:46 +02:00
Jouni Malinen
5be45e2e6e Fix per-SSID scan (scan_ssid=1)
Commit d3a9822542 broke per-SSID scan
by using the ssid variable for internal loop and by doing so,
overriding the value that was needed below to figure out whether the
scan is for a specific SSID. Fix this by using a temporary variable
instead when looping over network finding which frequencies to scan for.
2009-11-10 18:00:57 +02:00
Jouni Malinen
e6c0ebff68 Fix int_array_concat() to bail out on realloc failure
The previous version could have ended up dereferencing a NULL pointer
if the reallocation call were to fail.
2009-11-02 19:14:17 +02:00
Sam Leffler
4f34d51abe Do not schedule a new scan if no networks are enabled
This avoids an extra timeout to move to INACTIVE state.
2009-10-14 22:05:58 +03:00
Jouni Malinen
60b94c9819 Add preliminary background scan and roaming module design
This allows background scanning and roaming decisions to be contained in
a single place based on a defined set of notification events which will
hopefully make it easier to experiment with roaming improvements. In
addition, this allows multiple intra-ESS roaming policies to be used
(each network configuration block can configure its own bgscan module).

The beacon loss and signal strength notifications are implemented for
the bgscan API, but the actual events are not yet available from the
driver.

The included sample bgscan module ("simple") is an example of what can
be done with the new bgscan mechanism. It requests periodic background
scans when the device remains associated with an ESS and has couple of
notes on what a more advanced bgscan module could do to optimize
background scanning and roaming. The periodic scans will cause the scan
result handler to pick a better AP if one becomes available. This bgscan
module can be taken into use by adding bgscan="simple" (or
bgscan="simple:<bgscan interval in seconds>") into the network
configuration block.
2009-09-15 00:08:24 +03:00
Samuel Ortiz
3180d7a208 Getting back to DISCONNECTED afer SCANNING
After transitioning from DISCONNECTED to SCANNING, we never go back
to DISCONNECTED even though scanning is done or failed.
We're thus stuck in SCANNING while scanning is actually done.
2009-09-14 17:25:03 +03:00