ignore_broadcast_ssid=1 (or 2) were practically ignored if the Probe
Request frame included the SSID List or Short SSID List elements. Fix
this by requiring exact SSID match whenever ignore_broadcast_ssid is in
use regardless how SSID parameters are set in the Probe Request frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
According to IEEE P802.11ax/D6.0, 11.1.4.3.4 (Criteria for sending a
response), AP should answer Probe Request frames if either SSID or Short
SSID matches. Implement this part of the Short SSID use for the BSS (the
collocated 6 GHz BSS case is not covered in this commit).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This can be used in the future to implement support for RNR and scanning
extensions using a shorter field for the SSID.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
When wpa_supplicant receives another new peer event before the first one
has been processed, it tries to add a station to the driver a second
time (which fails) and then tears down the station entry until another
event comes in.
Fix this by only adding a station to the driver if it didn't exist
already.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We use the wired driver for wired port authentication with a slight
extension to add the port into a bridge upon successful authentication
and to remove it from the bridge when the session terminates.
Our expectation was that the Session-Timeout configuration at the RADIUS
server is respected, i.e. the session is terminated and would need
re-authentication - like it is working for WLAN sessions over the
nl80211 driver. Alas, it turned out the session is not terminated with
the wired driver.
It turned out that when ap_handle_session_timer() is executed, the
sta->flags of the wired port has only the WLAN_STA_AUTHORIZED bit set.
The WLAN_STA_AUTH bit, which is used to check whether the STA needs to
be de-authenticated, is missing.
Extend the check for any of the WLAN_STA_(AUTH | ASSOC | AUTHORIZED)
bits to solve this issue with the wired driver. That should not have any
side-effect for the WLAN cases since WLAN_STA_AUTH is expected to always
be set for those when there is an ongoing session and separate checks
for ASSOC and AUTHORIZED don't change this.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
If hostapd or wpa_supplicant is started with both -s and -f command line
arguments, debug log ended up being written only into syslog and the log
file was left empty. Change this so that the log entries will be written
to both places. Either -s or -f (or both) results in debug log to stdout
being disabled which was already the case.
Signed-off-by: Jouni Malinen <j@w1.fi>
This NS seems to go out from the AP interface every now and then and it
makes proxyarp_open_ebtables_ipv6 fails inconveniently often. That frame
should not really be there, but it's not clear what exactly is needed to
stop it going through. It does not come from the test operations
themselves, so ignore it for now to keep test results cleaner.
Signed-off-by: Jouni Malinen <j@w1.fi>
Explicitly clear cfg80211 scan cache to avoid issues from scan results
from previous test cases interfering with INTERWORKING_CONNECT
operation.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use LAST_ID of LIST_NETWORKS to load all the network entries iteratively
if there is large enough number of networks to not fit in a single
response.
Signed-off-by: Victor Ananyev <vindex10@gmail.com>
This allows starting point of the network list to be specified so that
the potentially long response can be fragmented into multiple fetch
operations.
Signed-off-by: Victor Ananyev <vindex10@gmail.com>
This removes dependency on tcpdump by using an already included test
tool for capturing frames with Ethernet headers. There were some issues
in getting tcpdump working on Ubuntu 19.10, so this seems to be a clean
way of addressing that.
Signed-off-by: Jouni Malinen <j@w1.fi>
Allow option (command line argument -e) to capture Ethernet headers
instead of IEEE 802.11 so that wlantest can be used as a replacement for
tcpdump/dumpcap for capturing.
Signed-off-by: Jouni Malinen <j@w1.fi>
Flush cfg80211 scan cache explicitly when running this test case to
avoid issues with the ROAM command not working due to a scan result from
an earlier test case. This was causing failures in the following test
case sequence:
rrm_beacon_req_active_ap_channels rrm_reassociation
Signed-off-by: Jouni Malinen <j@w1.fi>
Field wpa_s->sme.ht_sec_chan keeps secondary channel for the 40 MHz
band. This field is used to prepare a list of channels for the STA OBSS
scan. Initially, the secondary channel is set to HT_SEC_CHAN_UNKNOWN.
Later on, in function wpa_obss_scan_freq_list() it is obtained from the
current BSS HT operation IE. However, the secondary channel information
is not updated after channel switch, which may lead to an incorrect list
of channels prepared for the STA OBSS scan.
Update ht_sec_chan according to the channel switch event data to fix
this.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
There is no need to generate these OCSP responses for every single test
session. Generate these more dynamically if a test case that uses these
files is executed.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to generate these OCSP responses for every single test
session. Generate these more dynamically if a test case that uses these
files is executed.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to generate this OCSP response for every single test
session. Generate this more dynamically if the test case that uses the
particular file is executed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some of the error paths in go_neg_pbc() and go_neg_pin() did not wait
for the helper thread to complete processing. This could result in
unexpected behavior when the test case could have exited while the
thread was still performing tasks for the GO Negotiation. This could
result in getting stuck in one of the following test cases with
"go_neg_init_pbc thread caught an exception from p2p_go_neg_init: Group
formation timed out" showing up in the log.
This was hit, e.g., with the following test sequence:
no_go_freq p2p_channel_drv_pref_autogo
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of the loop that was polling for things to do every 0.25
seconds and instead, reacts to any data from VMs as soon as it becomes
available. This avoids unnecessary operations when no new data is
available and avoids unnecessary waits when new data becomes available
more quickly.
Signed-off-by: Jouni Malinen <j@w1.fi>
Wait for hostapd to enter the PTKINITDONE state before checking
connectivity. This is needed to avoid a race condition with UML
time-travel.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is more efficient since we can now start only the necessary number
of VMs instead of always forcing all VMs to start with one second delay.
This can also control the starting delay by keeping at most two VMs
starting at a time instead of using the hardcoded one second wait for
each consecutive VM.
Signed-off-by: Jouni Malinen <j@w1.fi>
For some reason, running tshark in the test cases can take significant
time especially with UML time-travel. Optimize this by reducing the
number of times tshark needs to be executed in the loop.
Signed-off-by: Jouni Malinen <j@w1.fi>
The wlan_mgt to wlan renaming is already included in most recent tshark
versions, so replace the backwards compatibility option to prefer the
new version so that current versions do not need to take the performance
hit.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like these test cases can fail with the new "Undefined
secondary channel: drop OBSS scan results" case. Add more checks to
determine if something is wrong with the connection.
In addition, force clearing of the cfg80211 scan cache on the main AP
interface so that a scan result from a previous test case cannot prevent
40 MHz channel bandwidth from being used. This could apparently happen
in the following test case sequence:
ap_ht40_scan_conflict obss_scan
Signed-off-by: Jouni Malinen <j@w1.fi>
These were doing practically the same thing, so get rid of the external
helper function and standardize on using hapd.wait_sta().
Signed-off-by: Jouni Malinen <j@w1.fi>
Wait for hostapd to indicate connection before disconnecting from the
station side. This avoids a race condition especially with UML
time-travel.
Signed-off-by: Jouni Malinen <j@w1.fi>
This lets one know the current neighbor list, and could be used
to populate the neighbor list of other hostapd processes.
For instance:
$ hostapd_cli -i vap0001 show_neighbor
04:f0:21:1e:ae:b0 ssid=04f0211eaeb0af190000802809 nr=04f0211eaeb0af1900008028090603022a00
$ hostapd_cli -i vap0000 set_neighbor 04:f0:21:1e:ae:b0 ssid=04f0211eaeb0af190000802809 nr=04f0211eaeb0af1900008028090603022a00
OK
$ hostapd_cli -i vap0000 show_neighbor
04:f0:21:1e:ae:b0 ssid=04f0211eaeb0af190000802809 nr=04f0211eaeb0af1900008028090603022a00
04:f0:21:c3:b2:b0 ssid=04f021c3b2b0af190000802809 nr=04f021c3b2b0af1900008028090603022a00
Signed-off-by: Ben Greear <greearb@candelatech.com>
Wait for hostapd to report completion of the connection before going
through the disconnection and reconnection steps to avoid a race
condition especially with UML time-travel.
Signed-off-by: Jouni Malinen <j@w1.fi>
Wait for hostapd to report connection completion before performing
connectivity test to avoid race conditions especially with UML
time-travel.
Signed-off-by: Jouni Malinen <j@w1.fi>
In the previous implementation connected STA performs OBSS scan
according to requests from its 20/40 MHz AP. However STA checks only 40
MHz intolerance subfield from HT Capabilities element in scan results.
Meanwhile, as per IEEE Std 802.11-2016, 11.16.12, STA should check
overlapping BSSs as well.
Note that all the required code to check overlapping BSSs did already
exist for AP mode since AP does those checks properly before operating
as 20/40 MHz BSS in the 2.4 GHz band. Use that existing code by replace
existing 40 MHz intolerance check in sme_proc_obss_scan() with the new
shared helper function check_bss_coex_40mhz().
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Move this implementation from check_40mhz_2g4() into a new helper
function check_bss_coex_40mhz function() so that it can be used in the
station mode case as well as the previously used AP mode case.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Let users delete a neighbor by BSSID alone if they prefer. The
underlying code already properly handled a NULL SSID, so just relax the
control interface command calling restrictions.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This gives us the network device name in logging messages, which can be
helpful when having one wpa_supplicant process handle multiple devices.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Support for dynamic VLANs depends on the Linux bridge ioctls.
Add this dependency explicitely to drivers make files.
This fixes build for minimal hostapd configs such as:
CONFIG_DRIVER_WIRED=y
CONFIG_FULL_DYNAMIC_VLAN=y
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
