WSC IE in Beacon and Probe Response frames should behave consistently
as far as the RF Bands attribute is concerned. Use the same dualband
condition for adding this into Probe Response frames since the value
is not really needed if the AP is not a dualband AP.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some deployed station implementations implement WPS incorrectly and
end up causing PBC session overlap issues by indicating active PBC
mode in a scan after the WPS provisioning step. Work around this by
ignoring active PBC indication in a Probe Request from a station that
completed PBC provisioning during the last five seconds.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The UFD (USB flash drive) configuration method was deprecated in WSC
2.0. Since this is not known to be used, remove the UFD implementation
from hostapd and wpa_supplicant to allow the WPS implementation to be
cleaned up. This removes the now unused OOB operations and ctrl_iface
commands that had already been deprecated by the new NFC operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
If WPS Registrar tries to provision a WPA/WPA2-Personal network without
including a valid Network Key, the network block cannot be used to
connect to the network. Reject such credential without adding the
network block. This makes wpa_supplicant send WSC_NACK as a response to
the invalid Credential and stop the provisioning process immediately
rather than only after trying unsuccessfully to connect to the network.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The old WPS interface for using NFC has no known deployments and even
the binary libraries referenced here are not easily available anymore.
Since the new interface for using NFC with WPS covers the same
functionality, remove the old implementation to clean up WPS
implementation.
Signed-hostap: Jouni Malinen <j@w1.fi>
When WPS is used with NFC connection handover, the AP may indicate its
operating channel within the credential information. Use this
informatiom, if present, to speed up the scan process.
Signed-hostap: Jouni Malinen <j@w1.fi>
This commit adds new wpa_supplicant ctrl_iface commands to allow
external programs to go through NFC connection handover mechanism
with wpa_supplicant taking care of the WPS processing. This version
includes only the case where wpa_supplicant is operating as a
station/Enrollee.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, WPS Registrar allowed multiple wildcard PINs to be
configured. This can get confusing since these PINs get assigned to any
Enrollee that does not have a specific PIN and as such, cannot really be
used with different PIN values in reasonable ways. To avoid confusion
with multiple enabled PINs, invalidate any previously configured
wildcard PIN whenever adding a new one.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Maintain state of WPS APs during iteration to find the correct AP for
WPS PIN operation when no specific BSSID is specified. This information
can be used for optimizing the order in which the APs are tried. This
commit is only adding the collection of the information and more
detailed debug information to make debug logs more helpful in figuring
out how the AP selection order could be improved.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Multiple memcmps of nonces were actually comparing only the first byte
instead of all 16 bytes. [Bug 462]
Signed-hostap: Eyal Shapira <eyal@wizery.com>
intended-for: hostap-1
This functionality could be shared for other commands, too, so move
it to a common function. In addition, implement the validation in a
bit more strict way to avoid accepting values like '-123' as a valid
PIN.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new hostapd ctrl_iface command WPS_NFC_TOKEN can now be used to
manage AP-as-Enrollee operations with NFC password token. WPS/NDEF
parameters to this command can be used to generate a new NFC password
token. enable/disable parameters can be used to enable/disable use of
NFC password token (instead of AP PIN) for external Registrars.
A preconfigured NFS password token can be used by providing its
parameters with new hostapd.conf fields wps_nfc_dev_pw_id,
wps_nfc_dh_pubkey, wps_nfc_dh_privkey, and wps_nfc_dev_pw. This use
will also depend on WPS_NFC_TOKEN enable/disable commands, i.e., the
configured NFS password token is disabled by default.
Signed-hostap: Jouni Malinen <j@w1.fi>
WPS_ER_NFC_CONFIG_TOKEN command can now be used to build a NFC
configuration token based on AP Settings learnt with WPS_ER_LEARN
or set with WPS_ER_CONFIG.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new wpa_supplicant ctrl_iface command WPS_NFC_TAG_READ can now be
used to process NFC tags read by external programs to initiate
wpa_supplicant to use NFC Configuration Token to create a new network.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new hostapd ctrl_iface command WPS_NFC_CONFIG_TOKEN can now be used
to fetch payload for an NFC configuration token so that an external
program can be used to write this on an NFC tag.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds a cleaner mechanism for handling NFC Password Tokens in the
WPS Registrar. There could be more than one active NFC Password Token in
use and as such, a list of tokens needs to be maintained. The old
WPS_OOB interface is still using the old mechanism that supports only a
single active NFC Password Token.
Signed-hostap: Jouni Malinen <j@w1.fi>
hostapd ctrl_iface can now be used to deliver payload from read
operation of an NFC tag. This allows operations without having to have
low-level NFC code within hostapd. For now, the new wps_nfc_tag_read
command can be used with NFC password tokens for the case where the AP
has an NFC device that is used to read an NFC tag from the station
Enrollee.
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of requiring low-level access to an NFC device and synchronous
operations, the new WPS_NFC_TOKEN and WPS_NFC ctrl_iface commands can be
used to build a NFC password token and initiate WPS protocol run using
that token (or pre-configured values) as separate commands. The
WPS_NFC_TOKEN output can be written to a NFC tag using an external
program, i.e., wpa_supplicant does not need to have low-level code for
NFC operations for this.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, only the maximum length 32 octets for OOB device password
was accepted. Since the specification allows a shorter password to be
used with limited OOB mechanism (e.g., small NFC tag), we should accept
lengths 16..32.
Signed-hostap: Jouni Malinen <j@w1.fi>
The earlier WPS 2.0 changes did not increase the wpabuf size when
adding a new attribute to the NFC password token. This could result
in aborting the application on wpabuf overflow if NFC out-of-band
mechanism is used with WPS 2.0 enabled.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
In AP which supports WPSv2 with only virtual push button, when PBC is
called, the WSC IE should include Selected Registrar Configuration
Methods attribute with the bit of the physical push button not set.
Signed-hostap: Yoni Divinsky <yoni.divinsky@ti.com>
wps_vendor_ext_m1 configuration parameter can now be used to add a
vendor specific attribute into the WPS M1 message, e.g., for
Windows Vertical Pairing.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If a wildcard PIN is used on any of the radios that hostapd is
controlling, invalidate the matching PIN on all the other radios
to avoid multiple uses of the same PIN.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use Device Password ID in WSC IE of Probe Request and Probe Response
frames to advertise immediate availability of WPS credentials per P2P
specification sections 3.1.2.1.1 (Listen State), 3.1.2.1.2 (Scan Phase),
and 3.1.2.1.3 (Find Phase).
For now, the Device Password ID is set only for the case where we are
active GO Negotiation with a specific peer. In practice, this means that
the Probe Response frames during pending GO Negotiation (whenever in
Listen state) indicate availability of the credential.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Remove unnecessary second copy of the URL and too long memory
allocation. In addition, avoid use of strcpy() to keep static analyzers
happier.
Signed-hostap: Jouni Malinen <j@w1.fi>
The SetSelectedRegistrar timeout was registered for each registrar
instance, but the only context pointer (struct subscription *) was
shared with each registrar which resulted in the timeout getting
cancelled for some of the registrar instances before the selected
registrar (ER) information was cleared.
In addition, when an ER unsubscribed from receiving events, the
selected registrar information got cleared only from a single
registrar.
Fix these issues by registering a pointer to the registrar
instance in the timeout and by iterating over all UPnP interfaces
when removing a subscription.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Remove the GPL notification text from files that were initially
contributed by Atheros Communications or Qualcomm Atheros.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, PINs that are added with a wildcard UUID were allowed to
be used only by a single Enrollee. However, there may be more than one
Enrollee trying to connect when an AP indicates that active Registrar
is present. As a minimal workaround, allow two Enrollees to try to use
the wildcard PIN. More complete extension could use timeout and allow
larger set of Enrollees to try to connect (while still keeping in mind
PIN disabling requirement after 10 failed attempts).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
While the exponential increase in the lockout period provides an
efficient mitigation mechanism against brute force attacks, this
additional trigger to enter indefinite lockout period (cleared by
restarting hostapd) will limit attacks even further by giving maximum of
10 attempts (without authorized user action) even in a very long term
attack.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like Windows 7 WPS implementation does not like multiple
Authentication/Encryption Type bits to be set in M7 AP Settings
attributes, i.e., it refused to add a network profile if the AP
was configured for WPA/WPA2 mixed mode and AP PIN was used to
enroll the network.
Leave only a single bit set in the Authentication/Encryption Type
attributes in M7 when the AP is acting as an Enrollee to avoid this
issue.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since wps_registrar_pbc_timeout is called to stop PBC, previously
registered wps_registrar_pbc_timeout must be canceled when canceling
the WPS operation.
Signed-off-by: Spencer Chang <jungwalk@gmail.com>
WPS overlap detection can detect false overlap if a P2P peer
changes UUID while authentication is ongoing. Changing UUID
is of course wrong but this is what some popular devices do
so we need to work around it in order to keep compatibility
with these devices. There already is a mechanism in WPS
registrar to skip overlap detection if P2P addresses of two
sessions match but it wasn't really triggered because the
address wasn't filled in in the caller function.
Let's fill in this address and also clean up WPS PBC sessions
on WSC process completion if UUID was changed.
Signed-hostap: Vitaly Wool<vitalywool@gmail.com>
When hostapd controls multiple radios, WPS operations are started on
all interfaces. However, when the provisioning run had been completed
successfully, actiove WPS mode was stopped only a single interface. Fix
this to iterate through all interfaces so that this is handled
consistently with the starting of WPS operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 628d54639a introduced number
of new WPS related ctrl_iface messages to hostapd. Some of these
were for ER events which do not make any sense to hostapd that
cannot operate as an ER. The WPS_EV_ER_SET_SELECTED_REGISTRAR one
from wps_registrar_sel_registrar_changed_event() was especially
problematic since it can cause wpa_supplicant ER code segfault due
to missing event data.
Revert all the ER specific changes from commit
628d54639a to get rid of the segfault
and undesired extra code in hostapd.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Some static analyzers complain about memset with '0' value. This was
used correctly here, but since use of strdup is about as good an option,
use that to silence the invalid warnings.
Signed-hostap: Jouni Malinen <j@w1.fi>
