Commit graph

187 commits

Author SHA1 Message Date
Jouni Malinen
5f482d55fd P2P: Allow immediate group idle timeout configuration
A special value p2p_group_idle=-1 can now be used to configure the P2P
group idle mechanism to terminate a P2P client group immediately on any
disconnection after the completion of the initial 4-way handshake.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-13 17:03:27 +03:00
Jouni Malinen
361cdf3400 P2P: Extend use of group formation timeout until end of 4-way handshake
Instead of relying on the P2P group idle timeout before the group
connection has been fully established, re-start the group formation
timeout in the end of the WPS provisioning step and clear it at the
successful completion of the initial 4-way handshake. This allows the
P2P group idle timeout to be set to a small value without triggering it
during the initial scan and connection attempt.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-13 17:01:15 +03:00
Jouni Malinen
205e6474a1 P2P: Fix p2p_connect join scan handler in error cases
wpa_drv_scan() may fail for the initial p2p_connect join scan request,
e.g., if the driver happened to be scanning at the time the new
operation was initialized. Previously, a special scan result handler was
registered regardless of whether the new scan was started. This could
result in partial scan results (e.g., from p2p_find social scan) from
being used as full results for join (or now more importantly for
p2p_connect auto) purposes. Fix this by registering the new scan result
handler only if wpa_drv_scan() returns success.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-13 16:13:14 +03:00
Jouni Malinen
b31be3a0fd P2P: Add automatic GO Negotiation vs. join-a-group selection
p2p_connect command can now be used with an optional "auto" parameter
to request wpa_supplicant to determine automatically whether to use
join-a-group operation (if the peer is operating as a GO) or group
formation. This makes it easier for external programs to handle
connection type selection by offloading this to wpa_supplicant. The
previously used p2p_connect join commands can be replaced with
p2p_connect auto to use this new mechanism.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-13 16:04:36 +03:00
Jouni Malinen
86ae2e8a42 P2P: Fix shared freq check and support AP mode validation
The previous commit did not use the correct pointer in all operations
and was specific to station mode interfaces. Fix and extend it to work
with AP/GO interfaces, too.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-04-08 20:42:45 +03:00
Jouni Malinen
4b15620609 P2P: Abort join-group operation if concurrent group cannot be supported
If the driver does not indicate support for multi-channel concurrency,
abort join-group operation if the end result would result in use of
multiple operating frequencies with the same radio.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-04-08 20:12:05 +03:00
Nirav Shah
103b8f4dea P2P: Disconnect P2P group on supplicant deinit
When a supplicant is deinited and shutting, disconnect from P2P groups.
This fixes a memory leak on variable dbus_groupobj_path on exiting
supplicant.

Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
2012-04-06 18:41:06 +03:00
Angie Chinchilla
eb6f8c2bd4 P2P: Fix crash for failure case when WSC PIN is entered incorrectly
When forming a P2P group using WSC PIN method, if the PIN is entered
incorrectly the P2P client supplicant instance will crash as a result
of cleanup happening on data that is still in use in a case where a
separate P2P group interface is used.

For example, here is the path for the first crash:
eap_wsc_process():
- creates struct wpabuf tmpbuf; on the stack
- sets data->in_buf = &tmpbuf;
- calls wps_process_msg()
- which calls wps_process_wsc_msg()
- which, in case WPS_M4: calls wps_fail_event()
- which calls wps->event_cb()
- wps->event_cb = wpa_supplicant_wps_event()
- wpa_supplicant_wps_event()
- wpa_supplicant_wps_event_fail()
- which calls wpas_clear_wps()
- which calls wpas_notify_network_removed()
- which calls wpas_p2p_network_removed()
- which calls wpas_p2p_group_formation_timeout()
- which calls wpas_group_formation_completed()
- which calls wpas_p2p_group_delete()
- which calls wpa_supplicant_remove_iface()
- which calls wpa_supplicant_deinit_iface()
- which calls wpa_supplicant_cleanup()
- which calls eapol_sm_deinit()
- ... which eventually uses the ptr data->in_buf to free tmpbuf, our
stack variable and then the supplicant crashes

If you fix this crash, you'll hit another. Fix it and then a segfault.
The way we're cleaning up and deleting data from under ourselves here
just isn't safe, so make the teardown portion of this async.

Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
intended-for: hostap-1
2012-04-06 18:22:03 +03:00
Jouni Malinen
3fc14102f8 P2P: Remove client group on Deauthentication reason code 3
The GO can indicate that the P2P Group session is ending by sending a
Deauthentication frame with reason code 3 (Deauthenticated because
sending STA is leaving) based on P2P specification section 3.2.9. Use
this reason code to remove the P2P client group without waiting for the
group idle timeout.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-03 16:45:28 +03:00
Eliad Peller
3c29244eb7 P2P: Add deinit_p2p_cli op to clear P2P client driver state
On P2P group removal, the GO is deinitialized correctly (and the vif
mode is set back to sta in case of nl80211), but the P2P client mode
wasn't deinitialized, and the nl80211 vif stays in P2P client mode.

Add a new deinit_p2p_cli op (similar to deinit_ap), which currently only
sets the interface back to station mode.

Signed-hostap: Eliad Peller <eliad@wizery.com>
intended-for: hostap-1
2012-04-01 21:41:23 +03:00
Johannes Berg
2d43d37ff2 DBus: Add ability to report probe requests
Some applications require knowing about probe requests to identify
devices. This can be the case in AP mode to see the devices before they
connect, or even in P2P mode when operating as a P2P device to identify
non-P2P peers (P2P peers are identified via PeerFound signals).

As there are typically a lot of probe requests, require that an
interested application subscribes to this signal so the bus isn't always
flooded with these notifications. The notifications in DBus are then
unicast only to that application.

A small test script is also included.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2012-04-01 21:14:48 +03:00
Johannes Berg
baf513d695 Pass signal strength through, fix units
The signal strength is currently never used as the only driver reporting
it is nl80211 which uses IEEE80211_RADIOTAP_DB_ANTSIGNAL which is never
populated by the kernel. The kernel will (soon) populate
IEEE80211_RADIOTAP_DBM_ANTSIGNAL instead though, so use that.

Also, since it was never really populated, we can redefine the signal
field to be in dBm units only.

My next patch will also require knowing the signal strength of probe
requests throughout the code (where available), so add it to the
necessary APIs.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2012-04-01 18:48:12 +03:00
Jouni Malinen
21d996f775 P2P: Add support for preferred channel list
p2p_pref_chan configuration parameter can now be used to set the
list of preferred channel for P2P GO Negotiation. This will be used
in the priority order if the peer does not support the channel we
are trying to use as the GO (configured operating channel or the
best 2.4 GHz/5 GHz channel) for the case where a forced channel is
not used.

p2p_pref_chan=<op class:channel>,...

For example:
p2p_pref_chan=81:1,81:2,81:3,81:4,81:5,81:6

This would configure 2.4 GHz channels 1-6 as the preferred ones with
channel 1 the most preferred option.

These configuration parameters can be set in wpa_supplicant.conf and
dynamically updated with "wpa_cli set <param> <value>".

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-03-29 21:28:34 +03:00
Jouni Malinen
8c472816fd P2P: Do not use group idle timeout during provisioning
Use the normal group formation timeout during the provisioning phase to
avoid terminating this process too early due to group idle timeout.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-03-27 18:04:06 +03:00
Jouni Malinen
f4329aa2d0 P2P: Validate p2p_oper_channel in p2p_group_add
If the p2p_group_add command does not specify the operating channel,
make sure the operating channel set in the configuration file meets
the P2P requirements in the same way as is done with the frequency
specified as the command parameter.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-03-26 22:06:48 +03:00
Jouni Malinen
10531d2166 P2P: Fix provisioning info clearing after successful WPS step
Previously, this provisioning info was cleared using the P2P Interface
Address of the GO as the key. That did not always work in the case the
where we joined an already running group. This could result in the next
connection to that same GO skipping provision discovery. Fix this by
finding the peer entry based on its P2P Device Address instead of the
P2P Interface Address which may not always be set.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
2012-03-01 22:06:03 +02:00
Jouni Malinen
75c208b9db P2P: Fix p2p_cancel to return success if GO Negotiation is stopped
If a GO Negotiation peer is found, wpas_p2p_stop_find() stops the
negotiation and p2p_cancel can return success.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-03-01 01:16:06 +02:00
Jouni Malinen
8e64f258c6 P2P: Optimize provisioning step scan for join-a-group sequence
Copy the SSID and frequency of the selected group into go_params in
join-a-running-group case so that the scan optimization can be used for
the provisioning step similarly to the case of group formation. This
uses a specific SSID and a single channel scan to avoid unnecessary
frames during the step.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-02-29 00:22:58 +02:00
Jouni Malinen
360182ed7c P2P: Advertise immediate availability of WPS credential
Use Device Password ID in WSC IE of Probe Request and Probe Response
frames to advertise immediate availability of WPS credentials per P2P
specification sections 3.1.2.1.1 (Listen State), 3.1.2.1.2 (Scan Phase),
and 3.1.2.1.3 (Find Phase).

For now, the Device Password ID is set only for the case where we are
active GO Negotiation with a specific peer. In practice, this means that
the Probe Response frames during pending GO Negotiation (whenever in
Listen state) indicate availability of the credential.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-02-27 23:14:35 +02:00
Jouni Malinen
dddc70455b P2P: Add more debug on group idle timeout
This makes it easier to debug issues with P2P group idle timeout.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-02-19 18:16:34 +02:00
Jouni Malinen
a7a30b90e5 P2P: Fix group idle timer cancellation on group removal
The wpas_p2p_group_idle_timeout was getting cancelled in the beginning
of wpas_p2p_group_delete(). However, in the case of P2P client role,
this function called wpa_supplicant_deauthenticate() next and that ended
up changing state to WPA_DISCONNECTED which resulted in
wpas_p2p_notif_disconnected() rescheduling the timeout. This left the
unexpected timeout behind after the group was removed. If another group
operation was started within P2P_MAX_CLIENT_IDLE (10) seconds, that
timeout could end up terminating the group while it was still being set
up.

Fix this by reordering wpas_p2p_group_delete() to cancel the group idle
timeout only after having called wpa_supplicant_deauthenticate(). The
group idle timeout is still rescheduled, but it gets removed immediately
afterwards when the actual group information is being cleared.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-02-19 18:10:20 +02:00
Jouni Malinen
6f3bc72be0 P2P: Allow channels to be removed from P2P use
A list of disallowed frequencies for P2P channel list can now be
configured with P2P_SET disallow_freq. The frequencies (or frequency
pairs) are comma separated. For example:
wpa_cli p2p_set disallow_freq 2462,5000-6000

The allowed P2P channel list is constructed by removing explicitly
disallowed channels from the channel list received from the driver.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-02-17 22:57:13 +02:00
Jouni Malinen
e22d4d957b Remove the GPL notification from files contributed by Atheros
Remove the GPL notification text from files that were initially
contributed by Atheros Communications or Qualcomm Atheros.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-02-11 19:39:36 +02:00
Piotr Nakraszewicz
d9a0f66696 P2P: Do not expire GO peer entry during group rekeying
If wpas_go_connected() is called during group rekeying the P2P GO peer
will expire. To prevent that check if group rekeying is not in progress.
2012-02-11 10:54:40 +02:00
Jouni Malinen
c427ac9211 P2P: Set Invitation Type to 1 for GO inviting to a persistent group
When a GO is operating a persistent group and invites a peer that has
been a P2P client in that persistent group, the Invitation Type in the
Invitation Request frame can be set to 1 to indicate that this is a
reinvocation of a persistent group. Do this based on the maintained
list of P2P clients that have been provided the credentials to this
group.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-02-06 21:54:36 +02:00
Jouni Malinen
f63b854215 P2P: Wait for PD-before-join response
Even though the Provision Discovery Response frame from PD-before-join
does not really provide any additional information, it can be better to
wait for it before starting the join operation. This adds a minimal
extra latency in the most common case and cleans up the sequence of
driver operations and debug log by avoiding potential processing of the
Provision Discovery Response while already running a scan for the actual
connection.

If transmission of Provision Discovery Request fails, join operation is
started without the additional wait. In addition, a new timeout is used
to start the join if Provision Discovery Response is lost for any
reason.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-02-05 20:52:24 +02:00
Jouni Malinen
c19316354e P2P: Skip event notification on PD Response in join-group case
Provision Discovery is used as a notification to the GO in the case we
are about join a running group. In such case, there is not much point in
indicating the provision discovery response events to external programs
especially when the PIN-to-be-displayed was different from the one
returned for the p2p_connect command. Skip this confusing event
completely for join-a-running-group case.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-02-05 20:20:36 +02:00
Dmitry Shmidt
df509539d4 Let wpa_supplicant_deinit_iface() know that process is terminating
This will be needed to be able to move ctrl_iface TERMINATING event to
the end of interface removal.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2012-01-29 20:15:48 +02:00
Jouni Malinen
b1aebbc427 P2P: Do not expire peer entry if we are connected to the peer
Even though we may not update P2P peer entry while connected to the
peer as a P2P client, we should not be expiring a P2P peer entry while
that peer is the GO in a group where we are connected as a P2P client.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-01-25 17:27:47 +02:00
Jouni Malinen
433cd2ce65 Stop sched_scan in number of cases where it should not be running
When a P2P group is removed, we better not leave possibly started
sched_scan running. This could happen when a separate group interface
was not used.

In addition, it looks safer to explicitly stop sched_scan before
starting P2P Listen or Find operations to make sure the offloaded
scanning is not running when doing similar P2P operations.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-01-23 18:26:09 +02:00
Jouni Malinen
6d92fa6e92 P2P: Allow Device ID to be specified for p2p_find command
dev_id=<P2P Device Addr> can now be specified as an argument to
p2p_find to request P2P find for a specific P2P device.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-01-08 09:25:29 -08:00
Jouni Malinen
e91829f9ac P2P: Stop remain-on-channel prior to starting join-a-group client
This fixes issues with drivers that do not handle concurrent
remain-on-channel and scan operations in a case where Provision
Discovery Response frame is not received to stop the Action frame
handshake.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-12-29 13:28:17 +02:00
Neeraj Kumar Garg
b8349523e4 P2P: Reject p2p_group_add if forced frequency is not acceptable
If the freq parameter is specified and we are already running legacy STA
on a different frequency with a driver that does not support
multi-channel concurrency, reject p2p_group_add. Same code already
exists in the path of P2P connection with go negotiation but is missing
for autonomous GO.

Signed-hostap: Neeraj Garg <neerajkg@broadcom.com>
2011-12-27 23:21:45 +02:00
Jouni Malinen
d7e70476f2 P2P: Use global->p2p_dev_addr instead of parent->own_addr
Start using global->p2p_dev_addr more consistently as the P2P Device
Address.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-25 23:58:03 +02:00
Jouni Malinen
fbdcfd577a P2P: Maintain a list of P2P Clients for persistent group on GO
Add a new persistent group network block field, p2p_client_list, to
maintain a list of P2P Clients that have connected to a persistent
group. This allows GO of a persistent group to figure out more easily
whether re-invocation of a persistent group can be used with a specific
peer device.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-22 22:47:41 +02:00
Jouni Malinen
87f841a140 P2P: Show persistent group info on P2P_PEER data
Add "persistent=<network id>" line to P2P_PEER ctrl_iface data
if a persistent group credentials are available for this peer.
This makes it easier for external programs to figure out when
a persistent group could be re-invoked with this peer.

For now, this information is only available on the P2P client,
but similar information can be added for GO once a list of P2P
clients is maintained with the persistent group data.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-22 21:45:20 +02:00
윤민홍
3b655312d4 P2P: Send D-Bus ServiceDiscoveryRequest signal for external SD processing
wpas_notify_p2p_sd_request() needs to be called when
p2p_sd_over_ctrl_iface is set to provide SD events over D-Bus similarly
to the ctrl_iface events.
2011-12-22 00:34:29 +02:00
Jouni Malinen
c81066153c P2P: Use hardcoded idle timeout of 10 seconds in P2P client role
The p2p_group_idle configuration parameter is much more useful for
GO role, so use a separate hardcoded value of 10 seconds in P2P
client role. In practice, this means that the P2P client role will
automatically tear down the group when the GO tears down the group.

The 10 second timeout is enough to recover from temporary disconnections
without unnecessary tearing down the group if the GO is still present
and allows the client to connect.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-18 22:21:22 +02:00
Jouni Malinen
4c2c675173 P2P: Fix disconnect event not to increase idle timeout
When P2P client is processing a disconnection event, make sure the P2P
idle timeout does not get increased, i.e., set a new timeout only if no
timeout is in use. wpa_state changes between DISCONNECTED and SCANNING
can generate multiple calls to wpas_p2p_notif_disconnect() and
previously this was enough to force the idle timeout never hit in
practice when in P2P client role.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-18 22:18:42 +02:00
Jouni Malinen
1ef2f7ffcf P2P: Fix Provision Discovery channel for some join-GO cases
The Provision Discovery Request needs to be sent on the operating
channel of the GO and as such, the frequency from the BSS table
(scan results) need to override the frequency in the P2P peer
table that could be based on the Listen channel of the GO.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-18 17:21:25 +02:00
Reinette Chatre
e5a359cf7e P2P: Make GO negotiation peer and group information available over D-Bus
The GO negotiation response is very cryptic at the moment. For a success
message we only know on which interface the negotiation succeeded, not
which peer. For a failure we know the interface also and a status code
(number).

It will be very useful for clients to know upon receipt of such a message
which peer the negotiation occurred with.

Now that the peer information is available and the API is changed
already, the function composing the D-Bus message might as well include
all GO negotiation information. This is done with a dict to make things
easier on clients if this result information changes down the line.

Signed-hostap: Reinette Chatre <reinette.chatre@intel.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2011-12-18 16:52:33 +02:00
Jouni Malinen
5506d18418 Fix compiler warning with CONFIG_NO_STDOUT_DEBUG=y
Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-11 18:19:24 +02:00
Jouni Malinen
7165c5dc1f P2P: Fix 32-bit compiler warnings on service discovery reference
Convert core wpa_supplicant code to use u64 instead of void * for the
P2P service discovery reference. Use uintptr_t in type casts in
p2p_supplicant.c to handle the conversion without warnings.

Note: This needs to be revisited for 128-bit CPU where sizeof(void *)
could be larger than sizeof(u64).

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-11 18:06:34 +02:00
Jouni Malinen
e3a0706b47 P2P: Fix Provision Discovery name in debug messages
Some debug messages used incorrect name for Provision Discovery.
Replace "Provisioning Discovery" with "Provision Discovery".

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-11 17:36:38 +02:00
Vitaly Wool
c3daaf3325 Skip WPS PBC overlap detection if P2P address is the same
WPS overlap detection can detect false overlap if a P2P peer
changes UUID while authentication is ongoing. Changing UUID
is of course wrong but this is what some popular devices do
so we need to work around it in order to keep compatibility
with these devices. There already is a mechanism in WPS
registrar to skip overlap detection if P2P addresses of two
sessions match but it wasn't really triggered because the
address wasn't filled in in the caller function.

Let's fill in this address and also clean up WPS PBC sessions
on WSC process completion if UUID was changed.

Signed-hostap: Vitaly Wool<vitalywool@gmail.com>
2011-12-11 12:03:18 +02:00
Jouni Malinen
502618f7c1 P2P: Clean up group formation on network block removal
If a P2P group network block is removed for any reason (e.g., wps_cancel
command) while the interface is in group formation, remove the group
formation timeout and indicate failure immediately. Previously, this
type of operations could end up leaving the timeout running and result
in somewhat unexpected group formation failure events later.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-10 12:56:42 +02:00
Jouni Malinen
c3f4278445 P2P: Add group ifname to P2P-PROV-DISC-* events
If Provision Discovery Request is sent for GO role (i.e., P2P Group ID
attribute is included), add the group interface name to the control
interface event on the GO. This makes it easier to figure out which
ctrl_iface needs to be used for wps_pbc/wps_pin command to authorize
the joining P2P client.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-06 21:57:17 +02:00
Jithu Jance
ec437d9e74 P2P: Skip duplicated provision discovery on join
If p2p_prov_disc join command is used prior to p2p_connect join,
skip the duplicated provision discovery exchange.

Signed-hostap: Jithu Jance <jithu@broadcom.com>
2011-12-06 21:44:57 +02:00
Jithu Jance
8c5f730983 P2P: Add optional "join" argument for p2p_prov_disc command
This can be used to request Provision Discovery Request to be sent
for the purpose of joining a running group, e.g., to request the GO
to display a PIN that we can then use with p2p_connect join command.

Signed-hostap: Jithu Jance <jithu@broadcom.com>
2011-12-06 21:28:02 +02:00
Jouni Malinen
a9e02d593d P2P: Clear show_group_started on GO start
The show_group_started variable could be left to 1 based on an earlier
failed attempt to start P2P client operation. This can result in
unexpected P2P-GROUP-STARTED event when a GO is started without group
formation (e.g., re-invoke a persistent group or start an autonomous
GO). Avoid this by explicitly clearing show_group_start when setting up
the GO.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-12-01 10:49:26 +02:00