Commit graph

762 commits

Author SHA1 Message Date
Jouni Malinen
508545f3a9 Add more wpa_supplicant AP mode parameters for the driver wrapper
This makes it easier to configure AP mode for drivers that take care
of WPA/RSN IE generation.
2010-04-11 20:02:01 +03:00
Jouni Malinen
4b768ed0b2 Add registerable callback for wpa_supplicant AP mode completion 2010-04-11 19:59:33 +03:00
Jouni Malinen
1c4c9c5078 Try to start a new scan more quickly after driver rejection
This speeds up recovery from some cases where the driver may refuse
a new scan request command temporarily.
2010-04-11 19:56:23 +03:00
Jouni Malinen
8cd82735cb Add an option to request a connection without a new scan 2010-04-11 19:55:40 +03:00
Jouni Malinen
64e58f5189 Add option for overriding scan result handler for a single scan 2010-04-11 19:53:31 +03:00
Jouni Malinen
814782b9fe Allow driver wrappers to indicate maximum remain-on-channel duration 2010-04-11 19:42:37 +03:00
Jouni Malinen
6700a277a9 Avoid dropping ctrl_iface on ENOBUFS error burst
These bursts can result in control interface monitors being detached
even if the external program is still working properly. Use much larger
error threshold for ENOBUFS to avoid this.
2010-04-11 19:29:24 +03:00
Jouni Malinen
cf4783e35f Deauthenticate instead of disassociate on disconnect command
This clears up authentication state in the driver and in case of
cfg80211, unlocks the BSS entry for the previously used AP.
2010-04-11 19:27:41 +03:00
Jouni Malinen
f3585c8a85 Simplify driver_ops for virtual interface add/remove
There is no absolute requirement for separating address allocation
into separate functions, so simplify the driver wrapper interface
to use just if_add and if_remove instead of adding the new
alloc_interface_addr() and release_interface_addr() functions.

if_add() can now indicate if the driver forced a different interface
name or address on the virtual interface.
2010-04-11 19:23:09 +03:00
Jouni Malinen
977b11747f Allow sub-second resolution for scan requests
This is in preparation to use cases that may benefit from more frequent
scanning.
2010-04-11 19:10:01 +03:00
Jouni Malinen
17a4734dc4 Optimize post-WPS scan based on channel used during provisioning
Scan only the frequency that was used during provisioning during the
first five scans for the connection. This speeds up connection in the
most likely case where the AP remains on the same channel. If the AP is
not found after these initial scans, all channels will be scanned.
2010-04-11 19:06:42 +03:00
Jouni Malinen
9efc3f2a4b SME: Handle association without own extra IEs
Need to check for this before calling ieee802_11_parse_elems().
2010-04-11 12:19:02 +03:00
Jouni Malinen
86d4f806da Add ctrl_iface command for triggering a roam to a specific BSS
'wpa_cli roam <bssid>' can now be used to test roaming within an ESS
(e.g., for FT over-the-air). This command will bypass a new scan and
will select the BSS based on the specified BSSID. It is responsibility
of the caller to make sure that the target AP is in the BSS table.
This can be done, e.g., by running a scan before the roam command,
if needed.
2010-04-10 22:56:55 +03:00
Jouni Malinen
a7b6c42232 Fix error messages to print ASCII MAC address, not the parse buffer 2010-04-10 22:46:54 +03:00
Jouni Malinen
0d7b44099f SME: Do not try to use FT over-the-air if PTK is not available 2010-04-10 22:39:49 +03:00
Jouni Malinen
e7846b6859 FT: Clean up wpa_sm_set_ft_params() by using common parse
Instead of parsing the IEs in the callers, use the already existing
parser in wpa_ft.c to handle MDIE and FTIE from initial MD association
response. In addition, this provides more complete access to association
response IEs to FT code which will be needed to fix FT 4-way handshake
message 2/4.
2010-04-10 11:36:35 +03:00
Jouni Malinen
579ce77122 FT: Deauthenticate in case of Reassoc Response validation error
If validation of the Reassociation Response frame fails during FT
Protocol, do not allow association to be completed; instead, force
deauthentication.
2010-04-09 16:59:27 +03:00
Jouni Malinen
f4ec630d1b FT: Set FT Capability and Policy properly in MDIE during initial MD assoc
This field needs to be copied from the scan results for the AP
per IEEE Std 802.11r-2008, 11A.4.2.
2010-04-09 16:41:57 +03:00
Jouni Malinen
76b7981d07 FT: Copy FT Capability and Policy to MDIE from target AP
This sets the FT Capability and Policy field in the MDIE to the values
received from the target AP (if available). This fixes the MDIE contents
during FT Protocol, but the correct value may not yet be used in initial
mobility domain association.
2010-04-09 16:26:20 +03:00
Jouni Malinen
d9a27b0455 Fix SME to update WPA/RSN IE for rsn_supp module based on AssocReq
When using wpa_supplicant SME (i.e., using nl80211), the rsn_supp
module was not informed of the WPA/RSN IE that was used in
(Re)Association Request frame. This broke roaming between APs that
use different security policy (e.g., changing between WPA/TKIP and
WPA2/CCMP APs) or when using PMKSA caching.
2010-04-07 10:31:06 +03:00
Jouni Malinen
32d5295f9d Add a drop_sa command to allow 802.11w testing
This drops PTK and PMK without notifying the AP.
2010-03-29 15:42:04 -07:00
Jouni Malinen
e820cf952f MFP: Add MFPR flag into station RSN IE if 802.11w is mandatory 2010-03-29 10:48:01 -07:00
Jouni Malinen
e2f74005f5 bgscan: Add signal strength change events
This allows bgscan modules to use more information to decide on when
to perform background scans. bgscan_simple can now change between
short and long background scan intervals based on signal strength
and in addition, it can trigger immediate scans when the signal
strength is detected to be dropping.

bgscan_simple takes following parameters now:
short interval:signal strength threshold:long interval
For example:
	bgscan="simple:30:-45:300"
2010-03-28 15:32:34 -07:00
Jouni Malinen
b625473c6c Add driver command and event for signal strength monitoring 2010-03-28 15:31:04 -07:00
Jouni Malinen
b766a9a293 Add freq_list network configuration parameter
This can be used to limit which frequencies are considered when
selecting a BSS. This is somewhat similar to scan_freq, but will
also affect any scan results regardless of which program triggered
the scan.
2010-03-26 22:45:50 -07:00
Jouni Malinen
62c72d7299 FT: Process reassoc resp FT IEs when using wpa_supplicant SME 2010-03-13 21:13:18 +02:00
Jouni Malinen
2a7e7f4e4a FT: Add driver op for marking a STA authenticated
This can be used with FT-over-DS where FT Action frame exchange
triggers transition to State 2 (authenticated) without Authentication
frame exchange.
2010-03-13 18:28:15 +02:00
Jouni Malinen
fe1919856c FT: Update SME frequency info before sme_associate() call
This is needed to allow FT-over-DS to request correct channel for
the reassociation with the target AP.
2010-03-13 18:26:25 +02:00
Jouni Malinen
71024cb255 FT: Request reassociation after successful FT Action frame exchange 2010-03-13 17:14:41 +02:00
Jouni Malinen
a7918ec749 wpa_cli: Improved command parameter tab completion 2010-03-12 19:43:15 +02:00
Jouni Malinen
037f83eb44 wpa_cli: Fix detach race with forked monitor process
Need to kill the monitor process before running detach command on
the monitor connection to avoid race where the monitor process may
end up getting the detach command result.
2010-03-12 17:34:56 +02:00
Jouni Malinen
dd63f314bd wpa_cli: Redisplay readline edit after event messages 2010-03-12 17:24:50 +02:00
Jouni Malinen
036f7c4aab FT: Add preliminary processing of FT Action Response from EVENT_RX_ACTION
Previously, this was only done with userspace MLME (i.e., driver_test.c);
now, driver_nl80211.c can deliver the FT Action Response (FT-over-DS)
for processing. The reassociation after successful FT Action frame
exchange is not yet implemented.
2010-03-12 00:43:00 +02:00
Jouni Malinen
a4652ce64c wpa_gui: Remove unneeded wpa_ctrl_request() msg_cb 2010-03-07 17:28:00 +02:00
Jouni Malinen
3234cba40e Remove unnecessary ifname parameter to sta_set_flags() driver op 2010-03-07 11:45:41 +02:00
Jouni Malinen
62847751e4 Remove unnecessary ifname parameter from sta_add() driver op 2010-03-07 11:42:41 +02:00
Jouni Malinen
17557ebe30 Remove forgotten ifname parameter from set_beacon() call 2010-03-07 10:04:35 +02:00
Felix Fietkau
4c32757d22 hostapd: add ifname to the sta_set_flags callback
This fixes multi-BSS STA operations (e.g., setting AUTHORIZED flag) with
nl80211-based drivers.
2010-03-06 20:44:31 +02:00
Jouni Malinen
23e2550c0e Remove unneeded CONFIG_EAP comments
These are not needed for WPS builds since CONFIG_WPS=y enables all
the needed EAP components.
2010-03-06 16:40:53 +02:00
Dmitry Shmidt
aa53509ffe Update priority list after priority change
Despite comments in the wpa_config_update_prio_list(struct wpa_config
*config) telling that it is called "if priority for a network is
changed", it is apparently not.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2010-03-06 11:13:50 +02:00
Kel Modderman
09bd6e8cca wpa_supplicant: fix FTBFS on Debian GNU/kFreeBSD
This patch allows wpa_supplicant to compile on Debian's kfreebsd
architectures.

Patch by Stefan Lippers-Hollmann based on work done by Petr Salinger
and Emmanuel Bouthenot for 0.6.X (http://bugs.debian.org/480572).
2010-03-06 10:16:47 +02:00
Jouni Malinen
3812464cda Add optional scan result filter based on SSID
filter_ssids=1 global configuration parameter can now be used to
enable scan result filtering (with -Dnl80211 only for now) based on
the configured SSIDs. In other words, only the scan results that have
an SSID matching with one of the configured networks are included in the
BSS table. This can be used to reduce memory needs in environments that
have huge number of APs.
2010-03-05 21:42:06 +02:00
Jouni Malinen
c9c38b0996 Make maximum BSS table size configurable
New global configuration parameter bss_max_count can now be used to
change the maximum BSS table size. The old fixed size limit (200) is
used as the default value for this parameter.
2010-03-05 20:20:09 +02:00
Jouni Malinen
ac26ebd8b5 Allow roam based on preferred BSSID regardless of signal strength 2010-02-28 11:09:58 +02:00
Jouni Malinen
36d1343a4b Do not inhibit suspend even if wpa_cli command fails
There is no point in inhibiting suspend in case wpa_supplicant is
not running and as such, return success unconditionally from this
script.
2010-02-27 20:03:13 +02:00
Jouni Malinen
207ef3fb12 Add suspend/resume notifications
wpa_supplicant can now be notified of suspend/resume events, e.g.,
from pm-action scripts. This allows wpa_supplicant to clear information
that may become invalid during a suspend operation.
2010-02-27 18:46:02 +02:00
Jouni Malinen
be8be6717d Clear current_bss pointer on disassociation/deauthentication
This is needed to allow the BSS table entry for the previously used
BSS to be removed. Now wpa_bss_in_use() can return 0 for the last BSS
that was used as soon as deauthentication/disassociation event has been
received.
2010-02-27 18:40:25 +02:00
Jouni Malinen
159dd3e28a Add more debug prints to make deauth/disassoc events clearer 2010-02-27 18:39:09 +02:00
Jouni Malinen
e824cc4648 Use os_snprintf instead of snprintf 2010-02-19 19:14:41 +02:00
Jouni Malinen
94d9bfd59b Rename EAP server source files to avoid duplicate names
This makes it easier to build both EAP peer and server functionality
into the same project with some toolchains.
2010-02-19 18:54:07 +02:00