driver_wired.c pulls in utils/common.h before net/if.h as a workaround
for NetBSD build. This results in IFNAMSIZ getting redefined and sparse
warning about this. Silence that warning by undefining the IFNAMSIZ
definition from common.h to allow the one from net/if.h being used. In
addition, remove duplicated inclusion of net/if.h.
Signed-off-by: Jouni Malinen <j@w1.fi>
Shuffle wpa_supplicant includes above system ones so that
to fix a compile problem on NetBSD where if_type #define
conflicts with the wpa_driver_if_type enum.
Signed-off-by: Roy Marples <roy@marples.name>
This converts most of the remaining perror() and printf() calls from
hostapd and wpa_supplicant to use wpa_printf().
Signed-off-by: Jouni Malinen <j@w1.fi>
Interfaces that take one or two seconds to reconfigure the link after we
set IFF_ALLMULTI or after we bring the interface up were dropping the
initial TX EAPOL packet which caused excessive delays in authentication.
This change applies to FreeBSD/DragonFly only.
Signed-hostap: Rui Paulo <rpaulo@FreeBSD.org>
This updates the license notification to use only the BSD license. The
changes were acknowledged by email (Gunter Burchardt, tmisu@gmx.de,
Mon, 02 Jul 2012 17:54:28 +0200).
Signed-hostap: Jouni Malinen <j@w1.fi>
This should fix EAPOL reauthentication and rekeying timeout issues
with Intel clients when using WMM (e.g., with IEEE 802.11n). These
stations do not seem to be able to handle EAPOL data frames as
non-QoS Data frames after the initial setup.
This adds STA flags to hapd_send_eapol() driver op to allow
driver_nl80211.c to mark the EAPOL frames as QoS Data frame
when injecting it through the monitor interface.
This patch adds support for wired IEEE 802.1X client on the Solaris.
I have tested with these:
OS : OpenSolaris 2009.06
EAP : EAP-MD5
Switch : Cisco Catalyst 2950
This patch allows wpa_supplicant to compile on Debian's kfreebsd
architectures.
Patch by Stefan Lippers-Hollmann based on work done by Petr Salinger
and Emmanuel Bouthenot for 0.6.X (http://bugs.debian.org/480572).
On DragonFly BSD, wired IEEE 802.1X fails with this message:
ioctl[SIOC{ADD/DEL}MULTI]: Invalid argument
This patch solves this issue.
I have tested with these:
OS : DragonFly BSD 2.4.0
EAP : EAP-TLS
Switch : Cisco Catalyst 2950
This is a patch for OpenBSD wired IEEE 802.1X. This is only for wired,
not wireless, because OpenBSD uses wpa_supplicant only on wired now.
http://www.openbsd.org/cgi-bin/cvsweb/ports/security/wpa_supplicant/
I have tested with these.
OS : OpenBSD 4.5
EAP : EAP-TLS
Switch : CentreCOM 8724SL
On NetBSD 5.0, when I use wired 802.1X, "Invalid argument" occurs
on SIOCADDMULTI ioctl and 802.1X fails.
I tried FreeBSD code, but "Address family not supported by protocol family"
occurs on SIOCADDMULTI ioctl and 802.1X fails, too.
This patch solves this issue.
I have tested with these:
OS : NetBSD 5.0
EAP : EAP-MD5
Switch : CentreCOM 8724SL
Use a parameter structure to pass in information that can be more easily
extended in the future. Include some of the parameters that were
previously read directly from hapd->conf in order to reduce need for
including hostapd/config.h into driver wrappers.
This commit merges the driver_ops structures and implementations from
hostapd/driver*.[ch] into src/drivers. This is only an initial step and
there is room for number of cleanups to share code between the hostapd
and wpa_supplicant parts of the wrappers to avoid unnecessary source
code duplication.
Do not use just the driver name for this since driver_ndis.c supports
both wired and wireless NDIS drivers and needs to indicate the driver
type after initialization.
