This extends OWE support in wpa_supplicant to allow DH groups 20 and 21
to be used in addition to the mandatory group 19 (NIST P-256). The group
is configured using the new network profile parameter owe_group.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds new wpa_supplicant configuration parameters (go_interworking,
go_access_network_type, go_internet, go_venue_group, go_venue_type) to
add a possibility of configuring the P2P GO to advertise Interworking
element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant network parameter group_mgmt can be used to
specify which group management ciphers (AES-128-CMAC, BIP-GMAC-128,
BIP-GMAC-256, BIP-CMAC-256) are allowed for the network. If not
specified, the current behavior is maintained (i.e., follow what the AP
advertises). The parameter can list multiple space separate ciphers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, wowlan_triggers were updated in kernel only during startup.
Also update it whenever it is set from the control interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant can now be configured to generate a network profile
automatically based on DPP configuration. The following
dpp_config_processing values can be used to specify the behavior:
0 = report received configuration to an external program for
processing; do not generate any network profile internally (default)
1 = report received configuration to an external program and generate
a network profile internally, but do not automatically connect
to the created (disabled) profile; the network profile id is
reported to external programs
2 = report received configuration to an external program, generate
a network profile internally, try to connect to the created
profile automatically
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new AKM is used with DPP when using the signed Connector to derive
a PMK. Since the KCK, KEK, and MIC lengths are variable within a single
AKM, this needs number of additional changes to get the PMK length
delivered to places that need to figure out the lengths of the PTK
components.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This exposes user configurable option to set bssid_hint for a network.
bssid_hint indicates which BSS has been found a suitable candidate for
initial association for drivers that use driver/firmware-based BSS
selection. Unlike the bssid parameter, bssid_hint does not limit the
driver from selecting other BSSs in the ESS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In some practical cases, it is useful to suppress joining to node in the
distance. The new field mesh_rssi_threshold could be used as RSSI
threshold for joining.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
If the uuid configuration parameter is not set, wpa_supplicant generates
an UUID automatically to allow WPS operations to proceed. This was
previously always using an UUID generated from the MAC address. This
commit adds an option to use a random UUID instead. The type of the
automatically generated UUID is set with the auto_uuid parameter: 0 =
based on MAC address (default; old behavior), 1 = random UUID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds an option to configure wpa_supplicant to use the perfect
forward secrecy option in FILS shared key authentication. A new build
option CONFIG_FILS_SK_PFS=y can be used to include this functionality. A
new runtime network profile parameter fils_dh_group is used to enable
this by specifying which DH group to use. For example, fils_dh_group=19
would use FILS SK PFS with a 256-bit random ECP group.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since VHT can be toggled explicitly, also expose being able to disable
HT explicitly, without requiring HT overrides. Continue making it
default to enabled though.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of deducing the wide (HT, VHT) channel configuration only
automatically in P2P mode, allow it to be configured in the network
in non-P2P mode.
Also allow all of these parameters to be configured through the control
interface or the configuration file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The userspace may want to delay the the first scheduled scan.
This enhances sched_scan to add initial delay (in seconds) before
starting first scan cycle. The driver may optionally choose to
ignore this parameter and start immediately (or at any other time).
This uses NL80211_ATTR_SCHED_SCAN_DELAY to add this via user
global configurable option: sched_scan_start_delay.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support for rejecting a BSS transition request using MBO reject
reason codes. A candidate is selected or rejected based on whether it is
found acceptable by both wpa_supplicant and the driver. Also accept any
candidate meeting a certain threshold if disassoc imminent is set in BTM
Request frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support to send GAS requests with a randomized transmitter address
if supported by the driver. The following control interface commands
(and matching configuration file parameters) can be used to configure
different types of randomization:
"SET gas_rand_mac_addr 0" to disable randomizing TX MAC address,
"SET gas_rand_mac_addr 1" to randomize the complete TX MAC address,
"SET gas_rand_mac_addr 2" to randomize the TX MAC address except for OUI.
A new random MAC address will be generated for every
gas_rand_addr_lifetime seconds and this can be configured with
"SET gas_rand_addr_lifetime <timeout>".
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 483dd6a5e0 ('Include peer
certificate always in EAP events') added this wpa_supplicant global
configuration parameter, but forgot to add the actual parsing of it, so
there was no way of setting the value.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a new wpa_supplicant network profile parameter
mka_priority=0..255 to set the priority of the MKA Actor.
Signed-off-by: Badrish Adiga H R <badrish.adigahr@gmail.com>
Previously, wpa_supplicant only supported hardcoded port == 1 in the
SCI, but users may want to choose a different port.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
So that the user can turn encryption on (MACsec provides
confidentiality+integrity) or off (MACsec provides integrity only). This
commit adds the configuration parameter while the actual behavior change
to disable encryption in the driver is handled in the following commit.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This enables configuring key_mgmt=NONE + mka_ckn + mka_cak.
This allows wpa_supplicant to work in a peer-to-peer mode, where peers
are authenticated by the pre-shared (CAK,CKN) pair. In this mode, peers
can act as key server to distribute keys for the MACsec instances.
This is what some MACsec switches support, and even without HW
support, it's a convenient way to setup a network.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This adds CONFIG_FILS=y build configuration option and new key
management options for FILS authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add configuration options that control publishing of fine timing
measurement (FTM) responder and initiator functionality via bits 70, 71
of Extended Capabilities element. Typically, FTM functionality is
controlled by a location framework outside wpa_supplicant. When
framework is activated, it will use wpa_supplicant to configure the
STA/AP to publish the FTM functionality. See IEEE P802.11-REVmc/D7.0,
9.4.2.27.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
The new network profile parameter group_rekey can now be used to specify
the group rekeying internal in seconds for IBSS.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous version did not really work at all and it ended up crashing
if the os_strdup(field->name) call failed.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE Std 802.11-2012, 10.19 (Public Action frame addressing) specifies
that the wildcard BSSID value is used in Public Action frames that are
transmitted to a STA that is not a member of the same BSS.
wpa_supplicant used to use the actual BSSID value for all such frames
regardless of whether the destination STA is a member of the BSS.
P2P does not follow this rule, so P2P Public Action frame construction
must not be changed. However, the cases using GAS/ANQP for non-P2P
purposes should follow the standard requirements.
Unfortunately, there are deployed AP implementations that do not reply
to a GAS request sent using the wildcard BSSID value. The previously
used behavior (Address3 = AP BSSID even when not associated) continues
to be the default, but the IEEE 802.11 standard compliant addressing
behavior can now be configured with gas_address3=1.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new parameter wps_disabled to network block (wpa_ssid). This
parameter allows WPS functionality to be disabled in AP mode.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Many of the global configuration parameters are written as strings
without filtering and if there is an embedded newline character in the
value, unexpected configuration file data might be written.
This fixes an issue where wpa_supplicant could have updated the
configuration file global parameter with arbitrary data from the control
interface or D-Bus interface. While those interfaces are supposed to be
accessible only for trusted users/applications, it may be possible that
an untrusted user has access to a management software component that
does not validate the value of a parameter before passing it to
wpa_supplicant.
This could allow such an untrusted user to inject almost arbitrary data
into the configuration file. Such configuration file could result in
wpa_supplicant trying to load a library (e.g., opensc_engine_path,
pkcs11_engine_path, pkcs11_module_path, load_dynamic_eap) from user
controlled location when starting again. This would allow code from that
library to be executed under the wpa_supplicant process privileges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Most of the cred block parameters are written as strings without
filtering and if there is an embedded newline character in the value,
unexpected configuration file data might be written.
This fixes an issue where wpa_supplicant could have updated the
configuration file cred parameter with arbitrary data from the control
interface or D-Bus interface. While those interfaces are supposed to be
accessible only for trusted users/applications, it may be possible that
an untrusted user has access to a management software component that
does not validate the credential value before passing it to
wpa_supplicant.
This could allow such an untrusted user to inject almost arbitrary data
into the configuration file. Such configuration file could result in
wpa_supplicant trying to load a library (e.g., opensc_engine_path,
pkcs11_engine_path, pkcs11_module_path, load_dynamic_eap) from user
controlled location when starting again. This would allow code from that
library to be executed under the wpa_supplicant process privileges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Spurious newlines output while writing the config file can corrupt the
wpa_supplicant configuration. Avoid writing these for the network block
parameters. This is a generic filter that cover cases that may not have
been explicitly addressed with a more specific commit to avoid control
characters in the psk parameter.
Signed-off-by: Paul Stewart <pstew@google.com>
WPA/WPA2-Personal passphrase is not allowed to include control
characters. Reject a passphrase configuration attempt if that passphrase
includes an invalid passphrase.
This fixes an issue where wpa_supplicant could have updated the
configuration file psk parameter with arbitrary data from the control
interface or D-Bus interface. While those interfaces are supposed to be
accessible only for trusted users/applications, it may be possible that
an untrusted user has access to a management software component that
does not validate the passphrase value before passing it to
wpa_supplicant.
This could allow such an untrusted user to inject up to 63 characters of
almost arbitrary data into the configuration file. Such configuration
file could result in wpa_supplicant trying to load a library (e.g.,
opensc_engine_path, pkcs11_engine_path, pkcs11_module_path,
load_dynamic_eap) from user controlled location when starting again.
This would allow code from that library to be executed under the
wpa_supplicant process privileges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Make the function available as part of the wpabuf API.
Use this renamed function where possible.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add a new value 2 to the pbss parameter of wpa_ssid structure, which
means "don't care". This value is used in infrastructure mode to request
connection to either AP or PCP, whichever is available in the scan
results. The value is also used in regular WPS (not P2P group formation)
to make WPS work with devices running as either AP or PCP.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
This avoids unnecessary flushing of the PMKSA cache entry and EAP
session data when processing SET_NETWORK commands that set a network
profile parameter to the same value that the parameter already has.
Introduce a new wpa_config_set() and wpa_config_set_quoted() return
value (==1) signifying that the new value being set for the
corresponding field equals to the already configured one so that the
caller can determine that nothing changed in the profile.
For now, this does not cover all the network profile parameters, but
number of the most commonly used parameters are included to cover the
Android use cases where the framework may have issued SET_NETWORK
commands that would have unnecessarily prevented use of PMKSA caching or
EAP fast reauthentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add cellular capability attribute to MBO IE and add MBO IE with cellular
capabilities to Probe Request frames. By default, cellular capability
value is set to Not Cellular capable (3).
Signed-off-by: David Spinadel <david.spinadel@intel.com>
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for IEEE 802.11ad devices.
Add a new "pbss" argument to network block. The argument is used
in the following scenarios:
1. When network has mode=2 (AP), when pbss flag is set will start
as a PCP instead of an AP.
2. When network has mode=0 (station), when pbss flag is set will
connect to PCP instead of AP.
The function wpa_scan_res_match() was modified to match BSS according to
the pbss flag in the network block (wpa_ssid structure). When pbss flag
is set it will match only PCPs, and when it is clear it will match only
APs.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Since hostapd supports ACS now, let's enable its support in
wpa_supplicant as well when starting AP mode.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
[u.oelmann@pengutronix.de: rebased series from hostap_2_1~944 to master]
[u.oelmann@pengutronix.de: adjusted added text in defconfig]
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
This allows the control interface SET command to be used to update the
sched_scan_plans parameter at runtime. In addition, an empty string can
be used to clear the previously configured plan.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add the option to configure scheduled scan plans in the config file.
Each scan plan specifies the interval between scans and the number
of scan iterations. The last plan will run infinitely and thus
specifies only the interval between scan iterations.
usage:
sched_scan_plans=<interval:iterations> <interval2:iterations2> ... <interval>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
A new network profile configuration parameter max_oper_chwidth=3 can be
used to specify preference to enable 80+80 MHz VHT channel for IBSS. If
that is set, the first 80 MHz segment is specified based on the
frequency parameter in the network profile and the second segment is
selected automatically (which will practically be limited to a single
possibility due to DFS requirements in most countries).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Number of places were calling functions that are not included in
CONFIG_NO_WPA=y build anymore. Comment out such calls. In addition, pull
in SHA1 and MD5 for config_internal.c, if needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some APs may send RSC octets in EAPOL-Key message 3 of 4-Way Handshake
or in EAPOL-Key message 1 of Group Key Handshake in the opposite byte
order (or by some other corrupted way). Thus, after a successful
EAPOL-Key exchange the TSC values of received multicast packets, such as
DHCP, don't match the RSC one and as a result these packets are dropped
on replay attack TSC verification. An example of such AP is Sapido
RB-1732.
Work around this by setting RSC octets to 0 on GTK installation if the
AP RSC value is identified as a potentially having the byte order issue.
This may open a short window during which older (but valid)
group-addressed frames could be replayed. However, the local receive
counter will be updated on the first received group-addressed frame and
the workaround is enabled only if the common invalid cases are detected,
so this workaround is acceptable as not decreasing security
significantly. The wpa_rsc_relaxation global configuration property
allows the GTK RSC workaround to be disabled if it's not needed.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
All interface globals are now exposed as D-Bus properties of type
string, and parsed via the normal interface global parsing functions.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Upon any change in the currently used channels evaluate if a GO should
move to a different operating frequency, where the possible scenarios:
1. The frequency that the GO is currently using is no longer valid,
due to regulatory reasons, and thus the GO must be moved to some
other frequency.
2. Due to Multi Concurrent Channel (MCC) policy considerations, it would
be preferable, based on configuration settings, to prefer Same
Channel Mode (SCM) over concurrent operation in multiple channels.
The supported policies:
- prefer SCM: prefer moving the GO to a frequency used by some other
interface.
- prefer SCM if Peer supports: prefer moving the GO to a frequency
used by some other station interface iff the other station
interface is using a frequency that is common between the local and
the peer device (based on the GO Negotiation/Invitation signaling).
- Stay on the current frequency.
Currently, the GO transition to another frequency is handled by a
complete tear down and re-setup of the GO. Still need to add CSA flow to
the considerations.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The mesh SAE auth often fails with master branch. By bisect I found
commit eb5fee0bf5 ('SAE: Add side-channel
protection to PWE derivation with ECC') causes this issue. This does not
mean the commit has a bug. This is just a CPU resource issue.
After the commit, sae_derive_pwe_ecc() spends 101(msec) on my PC (Intel
Atom N270 1.6GHz). But dot11RSNASAERetransPeriod is 40(msec). So
auth_sae_retransmit_timer() is always called and it can causes
continuous frame exchanges. Before the commit, it was 23(msec).
On the IEEE 802.11 spec, the default value of dot11RSNASAERetransPeriod
is defined as 40(msec). But it looks short because generally mesh
functionality will be used on low spec devices. Indeed Raspberry Pi B+
(ARM ARM1176JZF-S 700MHz) requires 287(msec) for new
sae_derive_pwe_ecc().
So this patch makes the default to 1000(msec) and makes it configurable.
This issue does not occur on infrastructure SAE because the
dot11RSNASAERetransPeriod is not used on it.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Allow proper update for listen_reg_class and listen_channel with
changed_parameters [CFG_CHANGED_P2P_LISTEN_CHANNEL] configuration for
command received through ctrl_interface. Without this, "set
p2p_listen_channel" and "set p2p_listen_reg_class" do not update the
listen channel. The D-Bus version was already setting these flags.
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
As far as IEEE 802.11 standard is concerned, WEP is deprecated, but at
least in theory, allowed as a group cipher. This option is unlikely to
be deployed anywhere and to clean up the implementation, we might as
well remove all support for this combination.
Signed-off-by: Jouni Malinen <j@w1.fi>
1. Add global p2p_cli_probe property to enable/disable Probe Request
frame RX reporting for connected P2P Clients. The property can be set to
0 - disable or 1 - enable. The default value is 0.
2. Enable Probe Request frame RX reporting for P2P Client on
WPA_COMPLETED state if p2p_cli_probe property is set to 1. Disable it
when an interface state is changing to any other state.
3. Don't cancel Probe Request frame RX reporting on wpa_stop_listen for
a connected P2P Client handling Probe Request frames.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
This commit adds a configurable parameter (wps_priority) to specify the
priority for the networks derived through WPS connection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes source code more consistent. The use within Android driver
interface is left as-is to avoid changes in the old PNO interface
definition.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new network profile parameter mem_only_psk=1 can be used to specify
that the PSK/passphrase for that network is requested over the control
interface (ctrl_iface or D-Bus) similarly to the EAP network parameter
requests. The PSK/passphrase can then be configured temporarily in a way
that prevents it from getting stored to the configuration file.
For example:
Event:
CTRL-REQ-PSK_PASSPHRASE-0:PSK or passphrase needed for SSID test-wpa2-psk
Response:
CTRL-RSP-PSK_PASSPHRASE-0:"qwertyuiop"
Note: The response value uses the same encoding as the psk network
profile parameter, i.e., passphrase is within double quotation marks.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add support to retrieve IPv4 config variables with the "get" control
interface command. This allows the ip_addr_* parameters for P2P+NFC
IP address assignment to be fetched from the GO.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Read p2p_go_ctwindow (0-127 TUs) from the config file, and pass it to
the driver on GO start.
Use p2p_go_ctwindow=0 (no CTWindow) by default.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Add fixed_freq=<0/1> network block parameter and pass it to the driver
when starting or joining an IBSS. If this flag is set, IBSS should not
try to look for other IBSS networks to merge with on different channels.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
The new reassoc_same_bss_optim=1 configuration parameter can now be used
to request wpa_supplicant to bypass the unnecessary Authentication frame
exchange when reassociating back to the same BSS with which the device
is already associated. This functionality is disabled by default since
it may cause undesired interoperability issues with some APs.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new "DUMP" and "SET <variable>" control interface commands can be
used to fetch global wpa_supplicant configuration parameters.
Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
This new wpa_supplicant configuration parameter can be used to force
passive scanning to be used for most scanning cases at the cost of
increased latency and less reliably scans. This may be of use for both
testing purposes and somewhat increased privacy due to no Probe Request
frames with fixed MAC address being sent out.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Current mesh code uses ap_max_inactivity as inactivity timer. This patch
makes it configurable.
There is another mesh inactivity timer in mac80211. The timer works even
if user_mpm=1. So this patch sets the max value to the timer for
workaround.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This is similar with domain_suffix_match, but required a full match of
the domain name rather than allowing suffix match (subdomains) or
wildcard certificates.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier for upper layer applications to get information
regarding the server certificate without having to use a special
certificate probing connection. This provides both the SHA256 hash of
the certificate (to be used with ca_cert="hash://server/sha256/<hash>",
if desired) and the full DER encoded X.509 certificate so that upper
layer applications can parse and display the certificate easily or
extract fields from it for purposes like configuring an altsubject_match
or domain_suffix_match.
The old behavior can be configured by adding cert_in_cb=0 to
wpa_supplicant configuration file.
Signed-off-by: Jouni Malinen <j@w1.fi>
In many applications it is useful not just to enumerate a group of well
known access points, but to use a address/mask notation to match an
entire set of addresses (ca:ff:ee:00:00:00/ff:ff:ff:00:00:00).
This change expands the data structures used by MAC lists to include a
mask indicating the significant (non-masked) portions of an address and
extends the list parser to recognize mask suffixes.
Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
This change adds the configuration options "bssid_whitelist" and
"bssid_blacklist" used to limit the AP selection of a network to a
specified (finite) set or discard certain APs.
This can be useful for environments where multiple networks operate
using the same SSID and roaming between those is not desired. It is also
useful to ignore a faulty or otherwise unwanted AP.
Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
This change generalizes the code used for parsing the configuration
option 'p2p_client_list' and makes it suitable to use it in other
contexts.
Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
There should not be a mesh-specific mechanism for setting up channel
parameters since that will just result in duplicated code. IBSS, mesh,
and AP mode can use the same data structures and parameters for setting
up such parameters.
Signed-off-by: Jouni Malinen <j@w1.fi>
The wps_vendor_ext array can be set using D-Bus Set(P2PDeviceConfig)
with the VendorExtension key in the dictionary. However, there was no
code for freeing the allocated memory when the interface is removed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the main PSK entry was cleared explicitly, but psk_list
could include PSKs for some P2P use cases, so clear it as well when
freeing config_ssid instances.
Signed-off-by: Jouni Malinen <j@w1.fi>
Maximum number of peer links is maximum number of connecting mesh peers
at the same time. This value is 0..255 based on the
dot11MeshNumberOfPeerings range.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
While these are using practically large enoungh buffer sizes, it is
better to be more consistent with checking os_snprintf() return value.
Signed-off-by: Jouni Malinen <j@w1.fi>
This converts os_snprintf() result validation cases to use
os_snprintf_error() in cases where success condition was used to execute
a step. These changes were done automatically with spatch using the
following semantic patch:
@@
expression E1,E2,E3;
statement S1;
@@
E1 = os_snprintf(E2, E3, ...);
- if (\( E1 >= 0 \| E1 > 0 \) && \( (size_t) E1 < E3 \| E1 < (int) E3 \| E1 < E3 \))
+ if (!os_snprintf_error(E3, E1))
S1
Signed-off-by: Jouni Malinen <j@w1.fi>
Derive rRK and rIK on EAP peer if ERP is enabled. The new wpa_supplicant
network configuration parameter erp=1 can now be used to configure the
EAP peer to derive EMSK, rRK, and rIK at the successful completion of an
EAP authentication method. This functionality is not included in the
default build and can be enabled with CONFIG_ERP=y.
If EAP authenticator indicates support for re-authentication protocol,
initiate this with EAP-Initiate/Re-auth and complete protocol when
receiving EAP-Finish/Re-auth.
Signed-off-by: Jouni Malinen <j@w1.fi>
This patch makes four MIB variables for plink configurable and sets the
correct default values based on IEEE Std 802.11s-2011.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
STAs that have different BSSBasicRateSet cannot connect to each other
as per IEEE 802.11s-2011 9.6.0c1:
"A mesh STA shall not establish a mesh peering with a mesh STA using a
different BSSBasicRateSet."
Make BSSBasicRateSet configurable to improve interoperability with other
stations.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Add a new option "mesh_ht_mode" that specifies the HT mode for the
mesh, with this option on, mesh beacons, actions frames, and probe
responses with include the appropriate HT information elements.
[original implementation by Chun-Yeow Yeoh <yeohchunyeow@gmail.com>]
[some fixes by Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
This adds definitions for the 128-bit level Suite B AKM 00-0F-AC:11. The
functionality itself is not yet complete, i.e., this commit only
includes parts to negotiate the new AKM.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add no_auto_peer parameter, which controls wheter a station will
automatically initiate peering to another mesh peer that comes into
range.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
Modify network mode to support mode number 5 when CONFIG_MESH is
enabled.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
Add user_mpm config parameter, when this is set to 1 (the default) the
peer link management is done on userspace, otherwise the peer management
will be done by the kernel.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
This commit introduces a QCA vendor command and event to provide an
option to use extended versions of the nl80211 connect/roam operations
in a way that allows drivers to offload key management operations to the
driver/firmware.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This was forgotten when the key_mgmt parser for SAE and FT-SAE was
added.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
The new openssl_cipher configuration parameter can be used to select
which TLS cipher suites are enabled for TLS-based EAP methods when
OpenSSL is used as the TLS library. This parameter can be used both as a
global parameter to set the default for all network blocks and as a
network block parameter to override the default for each network
profile.
Signed-off-by: Jouni Malinen <j@w1.fi>
mac_addr=2 and preassoc_mac_addr=2 parameters can now be used to
configure random MAC address to be generated by maintaining the OUI part
of the permanent MAC address (but with locally administered bit set to
1). Other than that, these values result in similar behavior with
mac_addr=1 and preassoc_mac_addr=1, respectively.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds experimental support for wpa_supplicant to assign random local
MAC addresses for both pre-association cases (scan, GAS/ANQP) and for
connections. MAC address policy for each part can be controlled
separately and the connection part can be set per network block.
This requires support from the driver to allow local MAC address to be
changed if random address policy is enabled. It should also be noted
that number of drivers would not support concurrent operations (e.g.,
P2P and station association) with random addresses in use for one or
both.
This functionality can be controlled with the global configuration
parameters mac_addr and preassoc_mac_addr which set the default MAC
address policies for connections and pre-association operations (scan
and GAS/ANQP while not connected). The global rand_addr_lifetime
parameter can be used to set the lifetime of a random MAC address in
seconds (default: 60 seconds). This is used to avoid unnecessarily
frequent MAC address changes since those are likely to result in driver
clearing most of its state. It should be noted that the random MAC
address does not expire during an ESS connection, i.e., this lifetime is
only for the case where the device is disconnected.
The mac_addr parameter can also be set in the network blocks to define
different behavior per network. For example, the global mac_addr=1 and
preassoc_mac_addr=1 settings and mac_addr=0 in a home network profile
would result in behavior where all scanning is performed using a random
MAC address while connections to new networks (e.g.,
Interworking/Hotspot 2.0) would use random address and connections to
the home network would use the permanent MAC address.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can be used to configure a Hotspot 2.0 Release 2 network externally
for a case where wpa_supplicant-based Interworking network selection is
not used and the update_identifier cannot be copied directly from a
cred.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Use an explicit memset call to clear any wpa_supplicant configuration
parameter that contains private information like keys or identity. This
brings in an additional layer of protection by reducing the length of
time this type of private data is kept in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is not really necessary check, but it keeps a static analyzer
happier by avoiding dead increment. Doing it this way rather than
removing the increment is less likely to cause problems when new entries
are added here in the future (the "dead" increment would be very much
needed in those cases).
Signed-off-by: Jouni Malinen <j@w1.fi>
The pointer to the current position is enough to figure out whether the
proto string is the first one in the buffer. Removing the separate
tracking variable cleans up a static analyzer warning on dead
assignment.
Signed-off-by: Jouni Malinen <j@w1.fi>
