Commit graph

223 commits

Author SHA1 Message Date
Jouni Malinen
4d32c0c44d P2P: Allow p2p_invite-persistent to specify channel for GO
The freq and ht40 parameters can now be used with the p2p_invite
command when reinvoking a persistent group as the GO.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-31 21:20:51 +03:00
Jouni Malinen
6ffdc2f7bd WFD: Add preliminary WSD request processing and response
This commit does not yet address support for different device roles,
i.e., the same set of subelements are returned regardless of which
role was indicated in the request.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-29 19:51:29 +03:00
Jouni Malinen
347d6a5b76 WFD: Add support for sending Wi-Fi Display service discovery requests
wpa_cli p2p_serv_disc_req command can now be used to request WSD
request to be sent to specified or all peers who support WSD.

format: wifi-display <list of roles> <list of subelements>
examples:
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source] 2,3,4,5
p2p_serv_disc_req 02:01:02:03:04:05 wifi-display [pri-sink] 3
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [sec-source] 2
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source+sink] 2,3,4,5
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source][pri-sink] 2,3,4,5

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-29 19:51:29 +03:00
Jouni Malinen
bf428a739c P2P: Fix memory leak with driver-based P2P management
If the P2P management operations are handled within the driver, the
P2P service entries were not freed when terminating wpa_supplicant.
Fix this by calling wpas_p2p_service_flush() even if the P2P module
within wpa_supplicant has not been initialized.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-24 20:45:22 +03:00
Jouni Malinen
b4a5dfa95d P2P: Limit maximum number of stored P2P clients to 100
This limits the maximum size of the p2p_client_list parameter that
is maintained at the GO for a persistent group. In other words, only
the 100 most recently seen P2P clients are kept in the list.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
2012-08-24 00:25:14 +03:00
Jouni Malinen
223167956c Improve p2p_client_list updates in configuration file
This list can get truncated due to too many addresses getting added.
Reorder the entries in a way that allows the most recently added values
to be maintained in the list and use better debug/error messages when
parsing the value.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
2012-08-24 00:25:14 +03:00
Jouni Malinen
99fcd40409 P2P: Allow scan operations during p2p_find
Previously, all station mode scan operations were either skipped or
delayed while any P2P operation was in progress. To make concurrent
operations easier to use, reduce this limitation by allowing a scan
operation to be completed in the middle of a p2p_find. In addition,
allow station mode association to be completed. When the station mode
operation is run to its completion (scan results not acted on,
connection to an AP completed, connection failed), resume the p2p_find
operation.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-23 19:42:53 +03:00
Jouni Malinen
05a77b3b46 P2P: Use 500 ms search delay by default during concurrent operations
If the p2p_find command is used without the delay parameter, a 500 ms
default search delay will now be used when any interface using the same
radio is in an concurrent operation. "p2p_find delay=0" can be used to
enforce the old behavior in such a case if needed.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-23 18:34:57 +03:00
Jouni Malinen
37448ede31 P2P: Add option for adding extra delay to p2p_find
A new optional delay=<search delay in milliseconds> parameter can now be
used with p2p_find command to request an extra delay between search
iterations. This can be used, e.g., to make p2p_find friendlier to
concurrent operations by avoiding it from taking 100% of the radio
resources.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-23 18:20:58 +03:00
Jouni Malinen
4f219667d7 P2P: Use larger GO config timeout if HT40 is used
Increase GO config timeout if HT40 is used since it takes some time
to scan channels for coex purposes before the BSS can be started.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-15 23:19:11 +03:00
Rajkumar Manoharan
e2308e4b45 P2P: Add optional "ht40" argument for p2p_connect
This can be used to start negotiated GO in 40 MHz channel width
in 5GHz band.

Signed-hostap: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
2012-08-15 23:07:44 +03:00
Rajkumar Manoharan
7aeac98509 P2P: Enable 40 MHz support for autonomous P2P group addition
Add optional "ht40" argument for p2p_group_add command to enable 40 MHz
in 5GHz band. This configures the secondary channel, when HT support is
enabled and if the HW supports 40 MHz channel width.

Signed-hostap: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
2012-08-15 22:53:01 +03:00
Rajkumar Manoharan
931228aa10 P2P: Move channel validation into a separate function
Signed-hostap: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
2012-08-15 22:44:34 +03:00
Jouni Malinen
067ffa2696 Convert os_realloc() for an array to use os_realloc_array()
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-13 21:21:23 +03:00
Jouni Malinen
8dba4aef11 P2P: Move group removal reason to a function parameter
wpa_s->removal_reason was set only when calling wpas_p2p_group_delete()
and while couple of call places did not set this, it should really be
set in each case. As such, it works better as a function parameter than
a variable in struct wpa_supplicant.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-11 12:41:31 +03:00
Michael Naumov
30ee769235 P2P: p2p_group_remove should fail on non-P2P interface
p2p_group_remove should only attempt to remove P2P group
interfaces and fail on non-P2P group interfaces.

Signed-hostap: Michael Naumov <michael.naumov@intel.com>
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
2012-08-11 12:06:23 +03:00
Eyal Shapira
462a7439e1 Add p2p_go_max_inactivity config option
This enables setting a different max inactivity timeout for P2P GO.
This timeout is used to detect inactive clients. In some scenarios
it may be useful to have control over this and set a shorter timeout
than the default 300s. For example when running STA and P2P GO interfaces
concurrently, the STA interface may perform scans which may cause the
GO to miss a disassoc / deauth frames from a client and keep assuming
that the client is connected until the inactivity detection kicks in.
300 secs is a bit too long for such scenarios and creates a bad user
experience.

Signed-hostap: Eyal Shapira <eyal@wizery.com>
2012-08-10 16:28:38 +03:00
Jouni Malinen
3df2f4fe99 P2P: Remove unused P2P_SCAN_SPECIFIC
This is not used anymore after the commit
e6ecfc4fd3.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-06-30 20:20:29 +03:00
Sunil Dutt Undekari
5bda43cdee P2P: Reject p2p_find when in provisioning
A p2p_find during provisioning shall not allow the enrollee to
pick the network, hence disable p2p_find during provisioning.

Signed-hostap: Sunil Dutt Undekari <duttus@codeaurora.org>
2012-06-25 14:05:49 +03:00
Aarthi Thiruvengadam
c66cf68d5c P2P: Fix fallback to GO Negotiation to avoid PD-before-join timeout
The wpas_p2p_pd_before_join_timeout could be left behind if the PD
Request in p2p_connect-auto case does not succeed. This timeout can
result in unexpected operations since it could trigger join operation
while going through GO Negotiation. Fix this by canceling the timeout
when falling back to GO Negotiation.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-06-20 21:38:31 +03:00
Jouni Malinen
73ccd08378 P2P: Fix group formation timeout on GO during WPS step
Commit 361cdf3400 changed the way the
group formation timeout is used on P2P client. However, it resulted in
clearing the timeout on the GO when the GO started beaconing. This is
not correct since the timeout is supposed to be maintained until at
least the completion of the WPS provisioning step. Fix this regression
by clearing the timeout here only in the case we are not GO in group
formation phase.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-06-08 18:22:03 +03:00
Jouni Malinen
5b37633364 P2P: Fix scan_res_handler setting for p2p_scan
The previous version set scan_res_handler unconditionally and then
cleared it if scan request failed. This can result in incorrect clearing
of the handler to NULL for a previously started scan that has not yet
completed. This can make p2p_find command fail to use the
start-after-scan-completion mechanism in some cases. Fix this by setting
scan_res_handler properly after having verified that the driver command
for starting the scan was successful.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
2012-06-06 17:07:46 +03:00
Sunil Dutt Undekari
84286a227b P2P: Improve p2p_prov_disc-auto robustness
Perform addition additional scan runs on the operating channel of the GO
(if known from previous scan results) and fall back to initiate the PD
for GO Negotiation if these additional scans do not detect the peer as
GO.

Signed-hostap: Sunil Dutt Undekari <duttus@codeaurora.org>
2012-06-06 15:46:05 +03:00
Nirav Shah
ad85320234 P2P: Fix P2P Group Formation timeout registration (use parent iface)
Commit 361cdf3400 extended the use of
group formation timeout for the way handshake, but the registration was
done on the group_interface while the cancellation was done on the
parent interface. Fix the registration to set the eloop timeout on
parent to address potential issues when using a separate group
interface.

Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
2012-06-04 21:58:34 +03:00
Jouni Malinen
b80eb89d8e P2P: Improve handling of p2p_connect-auto fallback
Commit aa9bb7644b improved robustness
of p2p_connect-auto mechanism by using older scan results to help in
determination whether the peer was operating a GO. Improve this by
accepting new GO information from scan-for-WPS-provisioning results
even if the GO is not yet ready for WPS.

In addition, fix an issue where Provision Discovery exchange timeout
could have left offchannel TX operation in progress when the fallback
was used.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-14 22:55:43 -04:00
Jouni Malinen
3bc462cb88 P2P: Add option for Provision Discovery before GO Negotiation
This is a workaround for interoperability issues with some deployed P2P
implementations that require a Provision Discovery exchange to be used
before GO Negotiation. The new provdisc parameter for the p2p_connect
command can be used to request this behavior without having to run a
separate p2p_prov_disc command.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-11 16:25:47 +03:00
Jouni Malinen
ab28911dbf P2P: Deinitialize global P2P context on P2P mgmt interface removal
The P2P implementation assumes that the first wpa_s interface instance
is used to manage P2P operations and the P2P module maintains a pointer
to this interface in msg_ctx. This can result in issues (e.g., use of
freed memory) when the management interface is removed. Fix this by
deinitializing global P2P data if the interface that created it is
removed. This will disable P2P until the next interface is added.

Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
2012-05-10 10:49:22 +03:00
Jouni Malinen
6f251b6bb5 P2P: Store SSID of the group in p2p_group data
This can be used with P2P management operations that need to verify
whether the local device is operating a specific group based on
P2P Group ID attribute from a peer.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-08 17:38:57 +03:00
Jouni Malinen
aa9bb7644b P2P: Allow older scan results to improve p2p_connect-auto robustness
Previusly the peer was assumed to not be operating a GO if the BSS entry
for it was not updated in the single scan run started by
p2p_connect-auto. This is not very robust since a scan may miss the peer
if either a Probe Request or Probe Response frame is lost. Improve
robustness by assuming the peer is still operating the GO and starting
the join operation. If the GO is not found during PD-for-join or the
single-channel scans during the join, fall back to GO Negotiation.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-08 17:38:57 +03:00
Wei-Jen Lin
1298c14594 Allow pbc_in_m1 workaround to be enabled in wpa_supplicant AP mode
This workaround for Windows 7 WPS probing mechanism was previously
allowed only with hostapd, but the same interoperability issue can
happen with wpa_supplicant AP/GO mode. Allow the workaround to be
enabled in wpa_supplicant configuration for these uses.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-03 16:51:04 +03:00
Wei-Jen Lin
f571b593ba P2P: Clone max_sta_num parameter for group interfaces
This is needed to allow the max_sta_num parameter set in the main
configuration file to apply to dynamically created P2P group
interfaces.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
2012-05-03 16:41:15 +03:00
Jouni Malinen
23c84252a4 P2P: Add option to force SSID/passphrase for GO Negotiation
An existing persistent group information can now be used to force GO
Negotiation to use the previously used SSID/passphrase from a persistent
group if we become a GO. This can be used as an alternative to inviting
a new P2P peer to join the group (i.e., use GO Negotiation with GO
intent 15 instead of starting an autonomous GO and using invitation),
e.g., in case a GO Negotiation Request is received from a peer while we
are not running as a GO. The persistent group to use for parameters is
indicated with persistent=<network id> parameter to p2p_connect.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-27 18:25:30 +03:00
Jouni Malinen
0918c4bf3b P2P: Add p2p_prov_disc auto mechanism
wpa_supplicant can now be requested to automatically figure out whether
the indicated peer is operating as a GO and if so, use join-a-group
style PD instead of pre-GO Negotiation PD.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-26 17:13:03 +03:00
Jouni Malinen
25a94f525c P2P: Fix PD Failure event to show peer device address
The p2p_dev_addr parameter in the P2P-PROV-DISC-FAILURE event (added in
commit f65a239ba4) was supposed to the P2P
Device Address of the peer, not the local device.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-26 17:09:02 +03:00
Masashi Honma
78039295e6 P2P: Remove unused variable
The "type" variable is not used in wpas_p2p_deinit_global().
So this patch removes it.

Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
2012-04-21 18:21:30 +03:00
Deepthi Gowri
f65a239ba4 P2P: Add provision discovery failure event
Add provisional discovery failure ctrl_iface event
(P2P-PROV-DISC-FAILURE) to indicate to the application layer in case of
PD failure.

Signed-off-by: Deepthi Gowri <deepthi@codeaurora.org>
2012-04-17 19:44:13 +03:00
Jouni Malinen
5f482d55fd P2P: Allow immediate group idle timeout configuration
A special value p2p_group_idle=-1 can now be used to configure the P2P
group idle mechanism to terminate a P2P client group immediately on any
disconnection after the completion of the initial 4-way handshake.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-13 17:03:27 +03:00
Jouni Malinen
361cdf3400 P2P: Extend use of group formation timeout until end of 4-way handshake
Instead of relying on the P2P group idle timeout before the group
connection has been fully established, re-start the group formation
timeout in the end of the WPS provisioning step and clear it at the
successful completion of the initial 4-way handshake. This allows the
P2P group idle timeout to be set to a small value without triggering it
during the initial scan and connection attempt.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-13 17:01:15 +03:00
Jouni Malinen
205e6474a1 P2P: Fix p2p_connect join scan handler in error cases
wpa_drv_scan() may fail for the initial p2p_connect join scan request,
e.g., if the driver happened to be scanning at the time the new
operation was initialized. Previously, a special scan result handler was
registered regardless of whether the new scan was started. This could
result in partial scan results (e.g., from p2p_find social scan) from
being used as full results for join (or now more importantly for
p2p_connect auto) purposes. Fix this by registering the new scan result
handler only if wpa_drv_scan() returns success.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-13 16:13:14 +03:00
Jouni Malinen
b31be3a0fd P2P: Add automatic GO Negotiation vs. join-a-group selection
p2p_connect command can now be used with an optional "auto" parameter
to request wpa_supplicant to determine automatically whether to use
join-a-group operation (if the peer is operating as a GO) or group
formation. This makes it easier for external programs to handle
connection type selection by offloading this to wpa_supplicant. The
previously used p2p_connect join commands can be replaced with
p2p_connect auto to use this new mechanism.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-13 16:04:36 +03:00
Jouni Malinen
86ae2e8a42 P2P: Fix shared freq check and support AP mode validation
The previous commit did not use the correct pointer in all operations
and was specific to station mode interfaces. Fix and extend it to work
with AP/GO interfaces, too.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-04-08 20:42:45 +03:00
Jouni Malinen
4b15620609 P2P: Abort join-group operation if concurrent group cannot be supported
If the driver does not indicate support for multi-channel concurrency,
abort join-group operation if the end result would result in use of
multiple operating frequencies with the same radio.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-04-08 20:12:05 +03:00
Nirav Shah
103b8f4dea P2P: Disconnect P2P group on supplicant deinit
When a supplicant is deinited and shutting, disconnect from P2P groups.
This fixes a memory leak on variable dbus_groupobj_path on exiting
supplicant.

Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
2012-04-06 18:41:06 +03:00
Angie Chinchilla
eb6f8c2bd4 P2P: Fix crash for failure case when WSC PIN is entered incorrectly
When forming a P2P group using WSC PIN method, if the PIN is entered
incorrectly the P2P client supplicant instance will crash as a result
of cleanup happening on data that is still in use in a case where a
separate P2P group interface is used.

For example, here is the path for the first crash:
eap_wsc_process():
- creates struct wpabuf tmpbuf; on the stack
- sets data->in_buf = &tmpbuf;
- calls wps_process_msg()
- which calls wps_process_wsc_msg()
- which, in case WPS_M4: calls wps_fail_event()
- which calls wps->event_cb()
- wps->event_cb = wpa_supplicant_wps_event()
- wpa_supplicant_wps_event()
- wpa_supplicant_wps_event_fail()
- which calls wpas_clear_wps()
- which calls wpas_notify_network_removed()
- which calls wpas_p2p_network_removed()
- which calls wpas_p2p_group_formation_timeout()
- which calls wpas_group_formation_completed()
- which calls wpas_p2p_group_delete()
- which calls wpa_supplicant_remove_iface()
- which calls wpa_supplicant_deinit_iface()
- which calls wpa_supplicant_cleanup()
- which calls eapol_sm_deinit()
- ... which eventually uses the ptr data->in_buf to free tmpbuf, our
stack variable and then the supplicant crashes

If you fix this crash, you'll hit another. Fix it and then a segfault.
The way we're cleaning up and deleting data from under ourselves here
just isn't safe, so make the teardown portion of this async.

Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
intended-for: hostap-1
2012-04-06 18:22:03 +03:00
Jouni Malinen
3fc14102f8 P2P: Remove client group on Deauthentication reason code 3
The GO can indicate that the P2P Group session is ending by sending a
Deauthentication frame with reason code 3 (Deauthenticated because
sending STA is leaving) based on P2P specification section 3.2.9. Use
this reason code to remove the P2P client group without waiting for the
group idle timeout.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-03 16:45:28 +03:00
Eliad Peller
3c29244eb7 P2P: Add deinit_p2p_cli op to clear P2P client driver state
On P2P group removal, the GO is deinitialized correctly (and the vif
mode is set back to sta in case of nl80211), but the P2P client mode
wasn't deinitialized, and the nl80211 vif stays in P2P client mode.

Add a new deinit_p2p_cli op (similar to deinit_ap), which currently only
sets the interface back to station mode.

Signed-hostap: Eliad Peller <eliad@wizery.com>
intended-for: hostap-1
2012-04-01 21:41:23 +03:00
Johannes Berg
2d43d37ff2 DBus: Add ability to report probe requests
Some applications require knowing about probe requests to identify
devices. This can be the case in AP mode to see the devices before they
connect, or even in P2P mode when operating as a P2P device to identify
non-P2P peers (P2P peers are identified via PeerFound signals).

As there are typically a lot of probe requests, require that an
interested application subscribes to this signal so the bus isn't always
flooded with these notifications. The notifications in DBus are then
unicast only to that application.

A small test script is also included.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2012-04-01 21:14:48 +03:00
Johannes Berg
baf513d695 Pass signal strength through, fix units
The signal strength is currently never used as the only driver reporting
it is nl80211 which uses IEEE80211_RADIOTAP_DB_ANTSIGNAL which is never
populated by the kernel. The kernel will (soon) populate
IEEE80211_RADIOTAP_DBM_ANTSIGNAL instead though, so use that.

Also, since it was never really populated, we can redefine the signal
field to be in dBm units only.

My next patch will also require knowing the signal strength of probe
requests throughout the code (where available), so add it to the
necessary APIs.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2012-04-01 18:48:12 +03:00
Jouni Malinen
21d996f775 P2P: Add support for preferred channel list
p2p_pref_chan configuration parameter can now be used to set the
list of preferred channel for P2P GO Negotiation. This will be used
in the priority order if the peer does not support the channel we
are trying to use as the GO (configured operating channel or the
best 2.4 GHz/5 GHz channel) for the case where a forced channel is
not used.

p2p_pref_chan=<op class:channel>,...

For example:
p2p_pref_chan=81:1,81:2,81:3,81:4,81:5,81:6

This would configure 2.4 GHz channels 1-6 as the preferred ones with
channel 1 the most preferred option.

These configuration parameters can be set in wpa_supplicant.conf and
dynamically updated with "wpa_cli set <param> <value>".

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-03-29 21:28:34 +03:00
Jouni Malinen
8c472816fd P2P: Do not use group idle timeout during provisioning
Use the normal group formation timeout during the provisioning phase to
avoid terminating this process too early due to group idle timeout.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-03-27 18:04:06 +03:00