Commit graph

1453 commits

Author SHA1 Message Date
Jouni Malinen
b204753115 tests: WPS HTTP protocol tests
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-05-03 18:26:50 +03:00
Oren Givon
2380d80493 tests: TDLS link status test
Add a test case for checking TDLS link status.

Signed-off-by: Oren Givon <oren.givon@intel.com>
2015-05-03 17:24:38 +03:00
Jouni Malinen
c53a3f29cd tests: IBSS RSN regression test for IBSS_RSN prior IBSS setup
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-05-03 17:15:45 +03:00
Jouni Malinen
f0174bff85 tests: Fix EAP-SIM/AKA protocol tests to use full header
Couple of the EAP-SIM/AKA protocol test cases were leaving out the
Reserved field. This was not intentional since these test cases were
targeting a specific Subtype processing instead of verifying truncated
header case (which is covered separately). Add the Reserved field to
allow the implementation to add an explicit, earlier check for this.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-05-03 16:32:59 +03:00
Jouni Malinen
cb346b49d2 tests: Extend D-Bus test cases to cover separate P2P Device operations
Number of the P2P test cases through D-Bus commands were not prepared
for there being a separate group interface when the P2P Device concept
is used.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-29 20:44:23 +03:00
Jouni Malinen
798c7951cf tests: ProxyARP with na_mcast_to_ucast=1
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-27 12:33:43 +03:00
Michael Braun
bbe9eddce0 tests: Change vlan_id back and forth
Enhance test ap_vlan_wpa2_radius_id_change to change the VLAN-ID
back as a last step. This ensures that the wpa_group for VLAN-ID 1
did not enter FATAL_FAILURE state during the test.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2015-04-26 16:56:22 +03:00
Jouni Malinen
f80fd58de6 tests: Check vlan_id information in STA output
In addition, this adds some delay between the authentication and data
connectivity test through the newly added VLAN and by doing so, makes
ap_vlan_wpa2_radius_id_change a bit more robust. It was possible for the
EAPOL-Key message 4/4 not having yet been processed by hostapd at the
time the data test started.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-04-26 15:59:19 +03:00
Michael Braun
bfcc073caf tests: Verify dynamic_vlan=required is honored with macaddr_acl=2
dynamic_vlan=required also applies to macaddr_acl=2 (RADIUS), especially
when used with WPA-PSK.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2015-04-25 10:28:19 +03:00
Jouni Malinen
2272f5aada tests: WPS AP iteration on no Selected Registrar and error case
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-24 17:55:33 +03:00
Jouni Malinen
cfbdb9958f tests: Increase wait timeout in autogo_m2d
The time before trying to associate with an AP that does not advertise
Selected Registrar TRUE is going to be incremented, so increase the
autogo_m2d timeout to avoid reporting incorrect errors due to missing
M2D events.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-24 17:55:32 +03:00
Jouni Malinen
9bbce25772 tests: D-Bus AddNetwork for AP mode
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-04-24 01:22:15 +03:00
Jouni Malinen
5bf30c6715 tests: wpa_supplicant INTERFACE_ADD/REMOVE with large number of vifs
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-24 01:22:15 +03:00
Jouni Malinen
f371869a96 tests: P2P protocol tests for too long variable length fields
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-22 11:44:19 +03:00
Michael Braun
515b176e9c tests: Verify RSN preauth with dynamic VLANs
This change add two new tests to verify hostapd operation when used with
VLANs. Both are based on pmksa_cache_preauth and enable dynamic VLANs,
pmksa_cache_preauth_vlan_used additionally uses a station with VID 1.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2015-04-13 17:08:10 +03:00
Jouni Malinen
1d0a917f36 tests: D-Bus BSS interface and WPS Type values
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-13 15:09:23 +03:00
Jouni Malinen
138bf11852 tests: INTERFACE_ADD/REMOVE with vif without creation/removal
This is also a regression test for INTERFACE_ADD parsing.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-04-04 11:02:22 +03:00
Jouni Malinen
febf575200 tests: EAP-TTLS with TLS session ticket enabled
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-01 12:57:11 +03:00
Jouni Malinen
0d33f5040f tests: EAP-PEAP/MSCHAPv2 with domain name
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-29 22:06:06 +03:00
Jouni Malinen
53f4ed68ee tests: WPA2-PSK AP with passphrase only in memory
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-28 11:08:31 +02:00
Jouni Malinen
b898a6ee72 tests: WPA2-Enterprise connection using EAP-pwd and NTHash
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-28 09:45:25 +02:00
Jouni Malinen
ce591c74bf tests: Make parallel-vm.py FAIL parser more robust
It looks like it was possible to receive an incomplete FAIL line and
break out from test execution due to a parsing error. Handle this more
robustly and log the error.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-26 22:20:35 +02:00
Jouni Malinen
25f2cb618c tests: INTERFACE_ADD/REMOVE with vif addition/removal
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-26 22:20:35 +02:00
Jouni Malinen
8278138e67 tests: Verify OSEN BSS flag in scan results
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-25 16:05:35 +02:00
Jouni Malinen
05121d3564 tests: Change proxyarp_open LL src MAC check to match requirements
Now that there is a kernel patch for IPv6 ProxyARP that is capable of
using the non-AP STAs MAC address as the link layer source address in
NA, validate that behavior rather than the temporary check for BSSID.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-24 20:33:33 +02:00
Jouni Malinen
a539d3f71f tests: Automatic reconnection on re-enabling temporarily disabled network
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-22 20:54:07 +02:00
Jouni Malinen
24b3b32316 tests: Remove debug print from ap_wpa2_psk_incorrect_passphrase
This development time debug print was forgotten into the test script.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-22 20:36:01 +02:00
Jouni Malinen
8aba435b16 tests: Make ap_vlan_wpa2_radius_id_change more robust
Wait for the 4-way handshake completion instead of assuming it gets done
in 0.1 seconds.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-20 17:51:18 +02:00
Jouni Malinen
898c959a6f tests: P2P_SERVICE_DEL asp all
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-20 15:56:59 +02:00
Jouni Malinen
5f6ce5b503 tests: INTERWORKING_SELECT blocking SCAN
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-20 15:56:59 +02:00
Jouni Malinen
97c6d0d873 tests: AP-STA-POSSIBLE-PSK-MISMATCH
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-19 13:18:44 +02:00
Jouni Malinen
a14a5f244a tests: Disable and re-enable hostapd interface
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-19 12:57:37 +02:00
Jouni Malinen
47af258687 tests: GET ip_addr_go
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-15 21:03:39 +02:00
Jouni Malinen
211bb7c5ea tests: WPA2-PSK-FT AP over DS and unexpected response
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-15 16:36:37 +02:00
Jouni Malinen
de52a2e259 tests: Fix parallel-vm.py test case name parsing
The 'params' argument was not used at all. Use it as an alternative
means for setting the list of test cases to execute.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-14 12:12:01 +02:00
Jouni Malinen
4f76eb81e9 tests: Add --valgrind argument to parallel-vm.py
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-14 12:09:23 +02:00
Jouni Malinen
eb9c155498 tests: P2P autonomous GO and many clients (P2P IE fragmentation)
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-14 10:58:17 +02:00
Jouni Malinen
d0cd00de6f tests: Verify wpa_supplicant AP mode events
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-14 10:14:47 +02:00
Jouni Malinen
f584b5a196 tests: Document dependency on python-crypto
Crypto.Cipher module is now needed to be able to run the 4-way handshake
protocol tests.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-07 23:47:02 +02:00
Jouni Malinen
e0c46c8e44 tests: Protocol testing for EAPOL-Key supplicant processing
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-07 17:18:33 +02:00
Jouni Malinen
0860b2199f tests: Make ap_acs_40mhz more robust
Explicitly clear cached scan results on the AP interface before starting
ACS. This avoids issues where conflicting BSS entries from previously
executed test cases could affect channel selection.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-07 17:02:40 +02:00
Jouni Malinen
68baa82cd2 tests: Add --short option for parallel-vm.py
This can be used to filter out test cases that take significantly longer
time to execute (15 seconds or longer). While this reduces testing
coverage, this can be useful to get a pretty quick coverage in
significantly faster time.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-07 12:23:39 +02:00
Johannes Berg
d2002f8334 tests: Allow running with arbitrary working directory
It's somewhat annoying that you can only run parallel-vm.py as
./parallel-vm.py, not from elsewhere by giving the full path,
so fix that by resolving the paths correctly in the scripts where
needed.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-03-07 12:23:07 +02:00
Johannes Berg
4f06261bd9 tests: parallel-vm.py: Use argparse module
Instead of hand-writing a (positional) parser, use the argparse module.
This also gets us nice help output.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-03-07 12:23:04 +02:00
Jouni Malinen
4e979d9de6 tests: Make ap_remove_during_acs* more robust
These test cases need to use the previous-AP-on-correct-band workaround
similarly to test_ap_acs.py test cases for now to work with
mac80211_hwsim limitations on channel survey.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-07 00:00:08 +02:00
Jouni Malinen
d970337da7 tests: Make suite_b* test cases more robust
Explicitly clear the cfg80211 BSS cache at the beginning of these test
cases to avoid matching BSS flags against incorrect AP.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-06 23:18:46 +02:00
Jouni Malinen
45de328602 tests: More thorough cache clearing in ap_hs20_hidden_ssid_in_scan_res
It looked like cfg80211 BSS entry for the zero-length SSID could remain
after this test case. Stop the AP and scan twice with flush-cache option
to make this less likely to occur and cause issues to following test
cases.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-06 23:17:12 +02:00
Jouni Malinen
9cc223c2f5 tests: Make offchannel_tx_roc_gas more robust
It was possible for this test case to fail if cfg80211 BSS cache
included an entry for the same BSSID on another channel from an earlier
test case. Fix this by epxlicitly flushing the cache. In addition, use
scan_for_bss() to make the test less likely to fail in case of heavy CPU
load.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-06 17:03:06 +02:00
Jouni Malinen
46dea617ae tests: WPS PIN and iterate through APs without selected registrar
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-06 15:37:02 +02:00
Jouni Malinen
50c3825c6d tests: DFS with wpa_supplicant AP mode
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-05 17:25:16 +02:00
Jouni Malinen
19ec6070ff tests: Fix workaround for limited channel survey in mac80211_hwsim
The way the current channel survey is implemented in mac80211_hwsim
requires for the ACS test cases to be run immediately after the same
radio has been on the expected operating band. This was worked around in
one of the test cases and errors ignored in couple. Extend this
workaround to cover all the test cases.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-03 16:01:52 +02:00
Jouni Malinen
9416e47f47 tests: Fix ap_vlan_wpa2_radius_id_change exception
This was supposed to be Exception("string") not "string".

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-03 15:40:19 +02:00
Johannes Berg
cba262e39b tests: Fix python typo
Clearly that should spell Exception.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-03-03 15:38:01 +02:00
Jouni Malinen
00c35673fd tests: Allow --shuffle-tests to be used with parallel-vm.py
This can be used to get more random sequence of test case execution
into use when running multiple VMs.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-03 09:47:25 +02:00
Jouni Malinen
fb7e0998b0 tests: P2P GO start with only 5 GHz band allowed
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-02 17:01:15 +02:00
Jouni Malinen
96cbb7b561 tests: Skip radius_acct_unreachable3 when not running under VM
It looks like the IP routing table changes used here to trigger
unreachability and following reachability of the server do not work very
well with full IP routing configuration, so run this test case only when
executed under vm-run.sh.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-02 16:30:13 +02:00
Jouni Malinen
bfc048b48f tests: P2P autonomous GO with large number of GO instances
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 22:36:53 +02:00
Jouni Malinen
58980654af tests: RADIUS server failure cases
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 22:36:52 +02:00
Jouni Malinen
5d695df5d1 tests: hostapd and get_station in multi-BSS configuration
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 22:36:52 +02:00
Jouni Malinen
5ff53fd6dd tests: RADIUS failover and failed attempt to return to primary server
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 22:36:52 +02:00
Jouni Malinen
7c5658c661 tests: RADIUS client address specified
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 22:36:52 +02:00
Jouni Malinen
1b5664f0fb tests: RADIUS Accounting server unreachable and multiple STAs
This verifies behavior on reaching RADIUS_CLIENT_MAX_ENTRIES.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 22:36:52 +02:00
Jouni Malinen
48d9065f7d tests: RADIUS Accounting server initially unreachable, but then available
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 22:36:52 +02:00
Jouni Malinen
ec1c483de0 tests: Not ready for GO Negotiation (listen/search)
These test cases verify that P2P_FIND and P2P_LISTEN operation continues
after having replied to GO Negotiation Request frame for which we are
not yet ready (i.e., GO Negotiation Response with status=1).

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 22:36:52 +02:00
Jouni Malinen
7041c16d5a tests: Open mode connection and SELECT_NETWORK to change network
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 15:56:11 +02:00
Jouni Malinen
6acca70536 tests: cfg80211 P2P Device and P2P_* command on incorrect interface
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 12:07:23 +02:00
Jouni Malinen
5de945fcc0 tests: cfg80211 P2P Device misuses
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 11:24:41 +02:00
Jouni Malinen
6d0b447464 tests: P2P_FIND with freq parameter to scan a single channel
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-28 22:06:24 +02:00
Jouni Malinen
dcd378ed2e tests: Make grpform_no_wsc_done more robust
It was possible for this test case to start a new group formation on
dev[1] while the first round was still going through the process of
processing group termination indication. That could result in the second
round failing unexpectedly.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-28 16:57:03 +02:00
Jouni Malinen
abeea374a4 tests: RADIUS server connect() failing during startup
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-28 15:45:17 +02:00
Jouni Malinen
8412dd52d1 tests: Increase default VM memory from 128M to 192M
It looks like the 128M default memory size for the hwsim test setup was
not large enough to cover all the needs anymore. Some of the test cases
using tshark could hit OOM with that size. Increase the default
allocation to 192M to avoid this type of issues.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-25 19:02:43 +02:00
Jouni Malinen
0f74bd41c5 tests: 4-way handshake and the first msg 4/4 getting lost
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-23 15:36:49 +02:00
Jouni Malinen
52352802ee tests: Linux packet socket workaround and EAPOL RX in operational state
This verifies that the packet socket workaround does not get disabled if
EAPOL frames are processed during operation state (i.e., when processing
reauthentication/rekeying on a functional association).

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-22 16:06:23 +02:00
Jouni Malinen
528a7d22d0 tests: VHT/HT preference in BSS selection
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-22 11:47:28 +02:00
Jouni Malinen
cfb5576d93 tests: Rename dmesg files to a unique name
This allows multiple dmesg files to be saved if a test case is executed
multiple times similarly to the other logfiles.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-21 16:07:53 +02:00
Johannes Berg
d0007ac9d7 tests: Add test to check disconnect in powersave
The kernel had two bugs (one in hwsim and one more important one in
mac80211) in this area, add a test to make sure we can disconnect
without any kernel issues while in powersave.

Also make sure that the TIM bit gets set and cleared again (by checking
with tshark.)

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-02-21 16:07:52 +02:00
Jouni Malinen
04bb845273 tests: Re-association to same BSS to toggle PMF status
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-19 16:37:12 +02:00
Jouni Malinen
4bcedaa400 tests: Re-sign expired test certificates
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-19 14:18:57 +02:00
Jouni Malinen
792eafa047 tests: Make wpas_mesh_password_mismatch more robust
It seems to be possible for dev2 (the one with incorrect password) to
stop retries before either dev0 or dev1 reports the authentication
failure event. For now, allow the test case pass if either dev0 or dev1
reports the event rather than requiring both to report this. The
expected behavior can be fine-tuned in the future if the reporting
behavior is modified to be more consistent.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-12 15:50:52 +02:00
Jouni Malinen
f245b45075 tests: Fix ap_{open,wpa2_psk}_wpas_in_bridge cleanup
Due to a copy-paste error, these test cases left 4addr mode enabled on
wlan5. This resulted in number of connect_cmd_* test cases failing if
executed after the wpas_in_bridge tests.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-11 16:50:06 +02:00
Jouni Malinen
1c9838b388 tests: Remove temporary config file in wpas_config_file
The new wpa_supplicant configuration file writing style leaves behind
the temporary file (<filename>.tmp) if renaming fails. Clean that up in
the test case execution.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-11 14:57:30 +02:00
Jouni Malinen
eb88a5ba74 tests: hostapd and external ifconfig down + up
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-11 10:31:12 +02:00
Jouni Malinen
380f3a8ba1 tests: Make autogo_join_auto_go_neg more robust
This test cases used to fail if dev1 had seen dev0 as a GO in an earlier
test case, e.g., when running it after autogo_fail. Fix this by clearing
scan results on dev1 at the beginning of the test case.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-10 12:09:07 +02:00
Jouni Malinen
c5b535ed1d tests: hostapd and start_disabled=1
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-09 19:57:46 +02:00
Jouni Malinen
7ebc7e8fa6 tests: wpa_supplicant DUMP/GET global parameter
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-08 22:49:58 +02:00
Jouni Malinen
2265376271 tests: INTERWORKING_ADD_NETWORK
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-08 22:49:58 +02:00
Jouni Malinen
9177b0a8c9 tests: Successful P2P_CONNECT-auto cases
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-08 13:59:57 +02:00
Jouni Malinen
d2b84e430c tests: P2P_CONNECT-auto not finding GO
This is a regression test for an earlier bug that resulted in using
freed memory after a P2P group interface was removed as part of
fallback-to-GO-Negotiation in P2P_CONNECT-auto.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-08 13:35:49 +02:00
Jouni Malinen
874057da4e tests: Make wpas_ctrl_many_networks more robust under valgrind
It is possible for a low powered CPU to take excessively long time to
delete 1000 network blocks when running under valgrind. This would have
resulted in the test case failing and the following reset operation
timing out which would then stop the test sequence completely.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-08 13:25:35 +02:00
Jouni Malinen
f77d6d4bd8 tests: Mesh authentication failure events
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-08 13:25:35 +02:00
Jouni Malinen
a0b3f8e2ff tests: Remove forgottend debug print from p2ps_connect_adv_go_persistent
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-07 16:29:22 +02:00
Jouni Malinen
c62bd5e44d tests: Remove forgotten debug print from grpform_pbc_overlap
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-07 15:38:29 +02:00
Ilan Peer
d821e2f294 tests: Use the global control interface in test_nfc_p2p.py
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-02-07 15:37:13 +02:00
David Spinadel
bbcbbd3701 tests: Modify autogo_bridge test to use group interface
1. Add get_group_ifname() to wpasupplicant.py
2. Use the function to get the interface name for the bridge.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2015-02-07 15:37:13 +02:00
Ilan Peer
4ef05faf43 tests: Modify test_p2p_discovery to use global and group interfaces
Modify the tests in test_p2p_discovery to use the global
control interface and group interface.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-02-07 15:37:13 +02:00
Ilan Peer
da749dc579 tests: Use the group control interface in p2p_channel_avoid
Use the group control interface to wait for P2P-REMOVE-AND-REFORM-GROUP
as the event is a group event.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-02-07 15:37:13 +02:00
Ilan Peer
d4f2ba749e tests: Use group control interface in autogo
P2P-PRESENCE-RESPONSE is a group event, and thus need
to use the group control interface.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-02-07 15:37:13 +02:00
Ilan Peer
75826fc6e6 tests: Use global control interface in wpas_ctrl_global
Use the global control interface to set/get the status of the
P2P Device.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-02-07 15:37:13 +02:00
Jouni Malinen
c4668009d0 tests: Remove unnecessary use of sudo from test cases
run-tests.py is running as root, so sudo does not need to be used
anymore from within each test case.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-07 15:37:13 +02:00
Jouni Malinen
b638f70316 tests: Replace subprocess.call for rm with os.remove()
There is no need to use sudo and external rm to remove files now that
run-tests.py is required to run as root.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-07 15:37:13 +02:00
Jouni Malinen
592015c3c1 tests: Fix wpas_config_file after implementation change
The new wpa_supplicant configuration writing design (rename instead of
write to original file) did not fail with the symlink-to-self case, so
replace this with the config file being replaced with a directory. In
addition, get rid of unnecessary use of subprocess since run-tests.py is
running as root nowadays.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-07 15:37:13 +02:00
Jouni Malinen
4cfc46934d tests: IBSS with WEP and TKIP
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-06 21:43:50 +02:00
Jouni Malinen
65013c9331 tests: ACS with acs_chan_bias parameter
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-06 18:02:33 +02:00
Ilan Peer
1cb3ad7362 tests: Use global control interface in test_p2p_concurrency
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-02-05 13:48:40 +02:00
Ilan Peer
2a9eb1494c tests: Use global control interface in test_p2p_service
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-02-05 13:48:40 +02:00
Ilan Peer
e9986d8b0b tests: Modify test_p2p_discovery to use global control interface
1. Modify discovery_stop to use global control interface when calling
   P2P_FLUSH.
2. Modify p2p_listen_and_offchannel_tx to use the global control
   interface when waiting for P2P PD event.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-02-05 13:48:40 +02:00
Eliad Peller
a918e48af1 tests: Add printk tracer to trace-cmd
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
2015-02-05 13:48:40 +02:00
Ben
d715738578 tests: Modify tests in test_ap_pmf to use own_addr()
Some of the tests used p2p_dev_addr() that can be different from
own_addr() if a dedicated P2P Device interface is used.

Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
2015-02-05 13:48:40 +02:00
Ben
3d8c7953e3 tests: Modify tests in test_hapd_ctrl to use own_addr()
Some of the tests used p2p_dev_addr() that can be different from
own_addr() if a dedicated P2P Device interface is used.

Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
2015-02-05 13:48:40 +02:00
Ben
1d21a5bee5 tests: Fix ap_wps_per_station_psk to use own_addr()
The test used p2p_dev_addr() that can be different from own_addr()
if a dedicated P2P Device interface is used.

Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
2015-02-05 13:48:40 +02:00
Ben
18945a8c8e tests: Fix ap_wpa2_psk_file to use own_addr
The test used p2p_dev_addr() that can be different from own_addr()
if a dedicated P2P Device interface is used.

Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
2015-02-05 13:48:40 +02:00
Matti Gottlieb
83e1bab022 tests: Fix destination address in ap_hs20_remediation_required_ctrl
Fix the destination address that is sent in the WNM-Notification to be
the BSS address opposed to the P2P address.

Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
2015-02-05 13:48:40 +02:00
Ilan Peer
36f2818784 tests: Use get_bss() with ifname in autogo
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-02-05 13:48:40 +02:00
Ilan Peer
fb9cf82eb3 tests: Add option to specify ifname to get_bss()
This is needed for cases that the group interface differs from the main
interface, i.e., when a dedicated P2P Device interface is used.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-02-05 13:48:40 +02:00
Ilan Peer
5270b2fbb7 tests: Use the global control interface in test_p2p_grpform
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-02-05 13:48:35 +02:00
Ilan Peer
c282b9b40e tests: Use global_request for SET commands in test_p2p_grpform
When the 'SET' command is used to configure parameters related to P2P
operation use the global control interface and not the per interface one
as otherwise the setting will only have effect on the interface and will
work if a dedicated P2P_DEVICE is used.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-02-05 13:38:10 +02:00
Ilan Peer
cef63d6b2f tests: Update group ifname in p2p_go_invite_auth
Once the connection is established need to call group_form_result() on
the invited device, as otherwise the group interface name is not updated
and the connectivity test is done with the main interface instead of the
group interface.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-02-05 13:38:10 +02:00
Ilan Peer
098a687ffb tests: Use global control interface in discovery_dev_id
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-02-05 13:38:10 +02:00
Ilan Peer
acd620258d tests: Modify autogo_legacy to use the group interface
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-02-05 13:38:10 +02:00
Ilan Peer
b0d697be91 tests: Use global control interface in wait_go_ending_session()
P2P_EVENT_GROUP_REMOVED is a global event, so use
wait_global_event() instead of wait_event().

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-02-05 12:50:44 +02:00
Jouni Malinen
644b24c6bb tests: Verify SD TX callback processing after P2P find is stopped
These are far from perfect since timing is quite difficult to match for
the case that behaved incorrectly. Anyway, it looks loke
p2p_service_discovery_peer_not_listening was able to hit the error now
and then, so this should be sufficient as a regression test case.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-04 20:47:14 +02:00
Jouni Malinen
c4f34de90d tests: P2PS and persistent group
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 17:00:56 +02:00
Jouni Malinen
12a793a606 tests: Increase grpform_ext_listen coverage
Include actual extended listen period in the test and confirm that the
device was available on a social channel during such period by using
non-social operating channel.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 16:43:02 +02:00
Jouni Malinen
2acd2985c6 tests: P2P_PROV_DISC error case
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 16:30:27 +02:00
Jouni Malinen
9406905384 tests: P2P listen channel optimization
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 16:22:59 +02:00
Jouni Malinen
2e6085c27b tests: OBSS scanning report processing
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 13:26:27 +02:00
Rajiv Ranjan
5095a6b6fc tests: P2P services
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:42:24 +02:00
Jouni Malinen
364e28c982 tests: Restore p2ps config_method in dbus_get_set_wps
This test case is modifying the list of enabled config_method values and
needs to restore "p2ps" option that is included by default. Without
this, P2PS executed after dbus_get_set_wps could fail.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Jouni Malinen
f4cd0f6454 tests: EAP-PEAP/MSCHAPv2 password failure
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-01 17:37:35 +02:00
Jouni Malinen
54f2cae2e6 tests: Make *_key_lifetime_in_memory more robust
It was possible for the GTK-found-in-memory case to be triggered due to
a retransmission of EAPOL-Key msg 3/4 especially when running test cases
under heavy load (i.e., timeout on hostapd due to not receiving the 4/4
response quickly enough). Make this false failure report less likely by
waiting a bit longer after the connection has been completed before
fetching the process memory.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-31 18:06:06 +02:00
Jouni Malinen
a1512a0cc7 tests: wpa_supplicant and station interface in a bridge
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-31 17:28:08 +02:00
Jouni Malinen
db5f6b2ca3 tests: RSN pre-authentication OOM in wpa_supplicant
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-31 13:45:52 +02:00
Jouni Malinen
7afa678033 tests: RSN pre-authentication timeout
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-31 13:35:31 +02:00
Jouni Malinen
d2432b8b7e tests: PMKSA cache size limit in wpa_supplicant
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-31 13:26:46 +02:00
Jouni Malinen
19879b4572 tests: Invalid NFC NDEF record handling
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-31 02:00:02 +02:00
Jouni Malinen
55c430b63c tests: Add capture file validation for IPv6 in proxyarp_open
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-30 21:55:46 +02:00
Jouni Malinen
efd0a6fbf1 tests: Add capture file validation for IPv4 in proxyarp_open
Verify that the expected frames were seend and unexpected frames
weren't.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-30 18:55:22 +02:00
Jouni Malinen
210a4f6a13 tests: Add another bridge port to proxyarp_open
Use another AP instance as a separate bridge port in the proxyarp_open
test cases to increase testing coverage for kernel proxyarp
functionality.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-30 18:55:22 +02:00
Jouni Malinen
87f0ede914 tests: Add brctl showmacs output to proxyarp_open test cases
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-30 18:55:22 +02:00
Jouni Malinen
9934ee1967 tests: Run the proxyarp_open test case both with and without ebtables
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-30 18:55:22 +02:00
Jouni Malinen
2076846cc4 tests: Fix tshark refactoring
Commit 2e1d7386e2 ('tests: Refactor tshark
running') added a helper function for running tshark. However, it did
not use the filter argument correctly, added an extra -Tfields on the
command line, and failed to use global variable. In practice, this ended
up disabling all the tshark sniffer checks. Fix that by using the filter
argument from the caller and marking the _tshark_filter_arg global.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-30 18:55:22 +02:00
Jouni Malinen
3a4bace428 tests: RADIUS server changing VLAN ID assignment
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-30 01:11:56 +02:00
Jouni Malinen
3b86e9d52c tests: PMKSA caching OOM error cases
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-30 00:14:57 +02:00
Jouni Malinen
915135e055 tests: hostapd OOM loop tests for WPA2-PSK and WPA2-EAP connection
These verify number of previously uncovered error paths.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-29 22:33:25 +02:00
Jouni Malinen
cdebd24db6 tests: OLBC AP table error cases
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-29 21:11:41 +02:00
Jouni Malinen
496a7a6ff9 tests: hostapd OOM loop targeting RADIUS accounting
The hostapd_oom_wpa2_eap test case did not always catch these code
paths, so add a variant of that test case explicitly targeting RADIUS
functions.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-29 20:52:30 +02:00
Jouni Malinen
2c528e9690 tests: cfg80211 DEL_STATION issued externally to hostapd
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-29 16:26:31 +02:00
Jouni Malinen
4a4cd04cad tests: RADIUS MAC ACL and accounting enabled
This ends up using the special User-Name = STA MAC address case for
Accounting-Request. In addition, add Chargeable-User-Identity for one of
the STAs.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-29 15:55:48 +02:00
Jouni Malinen
ef318402f6 tests: EAP-MSCHAPv2 server out-of-memory cases
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-28 16:17:25 +02:00
Jouni Malinen
95a15d793e tests: EAP-GTC server error cases
In addition, no-password-configured coverage extended to EAP-MD5 and
EAP-MSCHAPv2 as well.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-28 15:59:36 +02:00