This seems to be needed in some cases to avoid issues in test cases that
assume there are no other ERs running.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes the script check the environment for the current python
interpreter in use instead of assuming that the python executable points
to a python 2 interpreter.
Signed-off-by: Roger Zanoni <roger.zanoni@openbossa.org>
Only run-tests.py is actually executed, so there is no need to specify
the interpreter in all the helper files and test script files.
Signed-off-by: Jouni Malinen <j@w1.fi>
CONFIG_MODULE_TESTS=y build option can now be used to build in module
tests into hostapd and wpa_supplicant binaries. These test cases will be
used to get better testing coverage for various details that are
difficult to test otherwise through the control interface control. A
single control interface command is used to executed these tests within
the hwsim test framework. This commit adds just the new mechanism, but no
module tests are yet integrated into this mechanism.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify cases both with multiple peers (one of which not advertising any
services) and with multiple SD queries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like some of the discovery_* test cases have been failing every
now and then on the virtual server and the one second timeout could have
been a bit too short to cover some possible timing cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Enable hostapd control interface for the RADIUS server instance and
verify that the RADIUS server MIB counters are incremented.
Signed-off-by: Jouni Malinen <j@w1.fi>
This improves accuracy of the code coverage reports with hostapd-as-AS
and hlr_auc_gw getting analyzed separately.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a password that uses one, two, and three octet encoding
for UTF-8 characters. The value is tested against a pre-configured
hash to verify that utf8_to_ucs2() function works correctly.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like get_status() has failed in some test runs because of a
STATUS command returning an line without '=' on it. Instead of stopping
there on exception, report the unexpected line in the log and ignore it
to allow test to continue.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that NFC connection handover can be used in a case where
hostapd has an enabled password token.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Verify that PD Request followed by GO Negotiation Request is enough to
learn the Listen frequency of the peer.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
To test the code under the influence of time jumps, add the option
(--timewarp) to the VM tests to reset the clock all the time, which
makes the wall clock time jump speed up 20x, causing gettimeofday()
to be unreliable for timeout calculations.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Since wlantest is a separate process that is not synchronized with rest
of the test components, there can be some latency in it having the STA
entries and counters updated. There is a race condition between this
happening and then test script clearing or fetching data. Make this race
condition less likely to cause bogus test failures by adding some wait
between these operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
In addition to running the FLUSH command again, the pending monitor
interface events need be cleared in case the driver was running a scan
when reset() is called. This avoids issues, e.g., with discovery_dev_id
failing due to an unexpected P2P-DEVICE-FOUND event that was generated
by the pending scan operation that had not yet complete when the first
dump_monitor() call in reset() happened.
Signed-hostap: Jouni Malinen <j@w1.fi>
